Skip to content

Mechanical Engineering MCQ Questions

0
Answered
0
Correct
0%
Accuracy
Q101 Easy

In relation to mechanics of materials, which of the following options correctly defines a stress?

Stress = 2 x Force x Area
Stress = Force/Area
Stress = 2 x Force/Area
Stress = Area/2 x Force
Q102 Easy

What type of deformation may take place when large amounts of tensile strain are localized in a small area of a material?

Crinkling
Smashing
Necking
Crunching
Q103 Easy

In a heat exchanger application, what value does the term "temperature delta" refer to?

The resultant temperture of the heat exchange process
The heat energy lost through system operation
The difference in temperature between supply and return on one side of the system
The difference in temperature between the two sides exchanging heat energy
Q104 Easy

The difference between mechanical and chemical weathering is ____.

The length of time each takes to break
That only chemical weathering involves water
The way they affect the makeup of a rock
All of the above
Q105 Easy

What can be done to increase the capacity of a plate frame heat exchanger?

Install additional plates
Increase motor horsepower
Increase temperature delta
Increase motor rpm
Q106 Easy

Newton's law of cooling states that the rate of heat loss of a body is proportional to:

the absolute temperature of the body
the absolute temperature of the surrounding
the difference in temperatures between the body and its surroundings
Q107 Easy

Why are fan assemblies usually designed with spring isolators?

To increase airflow
To eliminate noise
To minimize vibration
To reduce friction
Q108 Easy

In manufacturing, a(n) __________ is used to produce large quantities of a few types of products.

Assembly-line layout
Process layout
Modular layout
Fixed-position layout
Q109 Easy

Within which angular range is the shear stress maximum if a body is subjected to tensile stress in one plane?

45º and 135º
50º and 175º
40º and 130º
55º and 180º
Q110 Easy

What does ASME stand for?

Association for Service of Mechanical Equipment
American Standards for Mechanical Equipment
American Society of Mechanical Engineers
Association of Science and Materials Engineering
Q111 Easy

In which type of welding is a mixture of Iron oxide and Aluminum used?

Metal inert gas welding
Tungsten inert gas welding
Submerged arc welding
Thermit welding
Q112 Easy

What is another name for a gear traing's torque ratio?

linkage constant
mechanical advantage
speed factor
Q113 Easy

Calculate the strain in a material whose original length before undergoing strain is 10 centimeters and the length after undergoing strain is 100 centimeters.

9
110
90
0.1
Q114 Easy

In __________, materials are physically or chemically changed to produce a product.

Utilitarian production
Assembly process.
Process manufacturing
All of these
Q115 Easy

What is the purpose of simple machines such as pulleys and levers?

To create mechanical advantage.
To establish geometric ratios
To lift heavy objects
Levers and pulleys are not considered simple machines.
Q116 Easy

Which type of thread is used in bench vices in manufacturing units?

Acme thread
Buttress thread
Knuckle thread
Square thread
Q117 Easy

What is the purpose of vehicle dynamics in automotive engineering?

To analyze fuel efficiency and emissions
To optimize vehicle handling and performance
To design safety systems and crash protection
To improve passenger comfort and interior design
Q118 Easy

What are the axes in Mohr's circle diagram?

X - axis : Normal Stress, Y - axis : Normal Strain
X - axis : Tensile Stress, Y - axis : Shear Stress
X - axis : Normal Stress, Y - axis : Shear Stress
X - axis : Stress, Y - axis : Strain
Q119 Easy

What is the SI unit for thermal resistance?

Kelvins per ohm
Ohms
joules per Kelvin
Kelvins per Watt
Q120 Easy

________ is the percent of design capacity a facility is actually expected to maintain.

Effective capacity
Process control
Motion studies
Electronic data interchange
Q121 Easy

What type of gear is used to transmit power at constant velocity ratio between two shafts the axes of which intersect at an angle?

Helical gear
Bevel gear
Worm gear
Rack and pinion gear
Q122 Easy

In which, among the following systems, does no heat or work cross its boundary?

Closed system
Isolated system
Open system
Q123 Easy

Creep is the tendency of a solid to:

deform permanently under mechanical stress
undergo elastic deformation
fracture under extreme loads
deform due to electromagnetic forces
Q124 Easy

What is an upward force exerted by a fluid that opposes the weight of an immersed object?

buoyancy
capillary action
surface tension
Q125 Easy

What is the force that prevents a material from being torn apart?

Adhesive strength
Tensile strength
Shear strength
Cohesive strength
Q126 Easy

The radius of a shaft is 5 millimeters. The shear stress on that shaft is 50 newtons per square millimeter and the polar moment of inertia is 10 (millimeters)4. Calculate the twisting moment on that shaft.

100 newton millimeters
200 newton millimeters
150 newton millimeters
250 newton millimeters
Q127 Easy

How many revolutions of crankshaft does it take to complete one working cycle in a four stroke engine?

2
4
6
8
Q128 Easy

What is the rotational force exerted by a spinning shaft?

Radial velocity
Momentum
Inertia
Torque
Q129 Easy

According to Bernoulli's principle, what happens in an ideal fluid with a decrease in pressure?

increase in speed
increase in volume
decrease in speed
Q130 Easy

The compression ratio of a diesel engine is:

10 to 15
15 to 25
40 to 50
50 to 60
Q131 Easy

Which among the following types of chips is usually produced during the machining of brittle materials?

Discontinuous chips
Continuous chips with no built up edges
Continuous chips with built up edges
Q132 Easy

What is the maximum allowable working pressure for a low pressure steam boiler?

5 psi
50 psi
15 psi
1 psi
Q133 Easy

How do we describe the process for determining the magnitudes of the components of a vector directed in two dimensions?

Vector Resolution
Vector Assesment
Vector calculus
Vector Calculation
Q134 Easy

Calculate the frictional power of an engine if the indicated power is 10 watts and the brake power is 5 watts.

5 watts
2 watts
0.5 watts
15 watts
Q135 Easy

Calculate the economic order quantity of a plant in which the total raw material utilized per year is 1600 tonnes,procurement cost per order is $1000 and the annual inventory carrying cost per item is $10.

428.68
565.68
636.68
700.68
Q136 Easy

What force describes the principle of Newton's second Law of Motion that objects naturally resist changes to their course of motion?

Inertia
Acceleration
Balance
Momentum
Q137 Easy

The ability of a material to embed small particles of dust, grit etc. is known as ___________.

conformability
bondability
embeddability
compressibility
Q138 Easy

Calculate the mechanical efficiency of an engine whose brake power is 20 watts and indicated power is 40 watts.

40%
50%
60%
70%
Q139 Easy

Calculate the moment of a 20 newtons force at 10 meters perpendicular distance from the point about which the moment is required.

200 newton meters
100 newton meters
150 newton meters
250 newton meters
Q140 Easy

Which law of thermodynamics captures the idea that higher temperature materials will always gravitate toward cooler temperatures?

The second law of Thermodynamics
The third law of Thermodynamics
The first law of Thermodynamics
The fourth law of Thermodyamics
Q141 Easy

What is the purpose of computer-aided engineering (CAE) in automotive design?

To simulate and analyze vehicle performance and behavior
To manufacture automotive components using 3D printing
To develop marketing strategies for vehicle sales
To perform routine maintenance and repairs on vehicles
Q142 Easy

Calculate the value of crippling load of a specimen, given that the crushing stress is 160 newtons per square meter, cross sectional area is 80 square millimeters, Rankine

7000
6400
8000
8500
Q143 Easy

What is the value of entropy of a substance at absolute zero temperature?

0
1
∞
-1
Q144 Easy

A process in which gas is heated such that the product of its pressure and volume remains constant is known as

isochoric process
isobaric process
isothermal process
hyperbolic process
Q145 Easy

What is the result of continous cyclic loads on a metal object?

Increased pliability
Hardened metal
Metal fatigue
Softened metal
Q146 Easy

Due to which of the following properties does molding sand adhere to the sides of the molding box?

Permeability
Plasticity
Adhesiveness
Cohesiveness
Q147 Easy

Calculate the coefficient of friction of a body whose limiting friction of which is 10 newtons and the value of the normal reaction is 5.

2
50
0.5
15
Q148 Easy

True or False: Silicon can be used to make microelectromechanical systems.

True
False
Q149 Easy

The shear stress is a maximum where the velocity is __________.

Small
The same
Acceleration
One half
Q150 Easy

What must happen to fuel oil at the burner for efficient combustion?

Desintigration
Oxygen depletion
Atomization
Conical spraying
Showing 150 of 195 questions

Teachers: using these Mechanical Engineering questions with a class? Tell us about your class.

Report a mistake

What's wrong?