Skip to content
Core Engineering

Mechanical Engineering interview questions and answers

80 questions. About 3 h 10 min to read them all.

By TestLab · Updated

Plan for an interview
80 questions

Track what you know and what to revise.

Sign in to track progress

You can open a few full answers without signing in. Sign in to read all

1

What is the zeroth law of thermodynamics?

The zeroth law of thermodynamics states that if two bodies are each in thermal equilibrium with a third body, they are in thermal equilibrium with each other. Thermal equilibrium means no net heat flows between them when they are in contact, so they are at the same temperature. This law makes temperature a measurable property and is the basis of every thermometer.

Read full answer

Applies toMechanical engineering (thermodynamics)

Meaning

  • If body A = body C in temperature and body B = body C in temperature, then A = B.

  • The third body © is the thermometer: it is brought into equilibrium with A and B in turn.

  • It was named “zeroth” because it was recognised as fundamental after the first and second laws had already been numbered.

Temperature Scales

Scale Ice point Steam point (1 atm) Relation
Celsius (°C) 0 100 —
Kelvin (K) 273.15 373.15 K = °C + 273.15
Fahrenheit (°F) 32 212 °F = 1.8 × °C + 32
Rankine (°R) 491.67 671.67 °R = °F + 459.67

The Kelvin scale is the absolute (thermodynamic) scale used in all thermodynamic equations.

Worked Example

Answer: 37 °C = 310.15 K = 98.6 °F. A clinical thermometer reads 37 °C when it reaches equilibrium with a person’s body.

  • K = 37 + 273.15 = 310.15 K

  • °F = 1.8 × 37 + 32 = 98.6 °F

The thermometer (body C) reads the person’s temperature only after it reaches thermal equilibrium with them, which is why it is held for a minute or so.

Types of Thermometers (Thermometric Properties)

Thermometer Property that changes with temperature
Liquid-in-glass Volume of mercury or alcohol
Constant-volume gas thermometer Pressure of gas
Thermocouple Seebeck EMF between two metals
RTD (e.g. Pt100) Electrical resistance (100 Ω at 0 °C)
Thermistor Resistance (semiconductor)
Pyrometer / IR thermometer Thermal radiation

Applications

  • Calibrating and using temperature sensors in industry (RTDs, thermocouples in boilers, furnaces and engines).

  • Defining temperature for all thermodynamic analysis of engines, refrigerators and heat exchangers.

2

State the first law of thermodynamics.

The first law of thermodynamics is the law of conservation of energy applied to thermodynamic systems: energy can neither be created nor destroyed, only converted from one form to another. For a closed system, the heat supplied equals the increase in internal energy plus the work done by the system: Q = ΔU + W. For a cycle, the net heat transfer equals the net work done: ∮δQ = ∮δW.

Read full answer

Applies toMechanical engineering (thermodynamics)

Forms of the First Law

Closed system (non-flow process): Q − W = ΔU (sign convention: Q positive when heat is added, W positive when work is done by the system)

Open system, steady flow (SFEE) per unit mass flow: q − w = (h₂ − h₁) + (V₂² − V₁²)/2 + g(z₂ − z₁)

where h is specific enthalpy (h = u + pv).

Worked Example 1: Closed System

Answer: internal energy rises by 300 kJ. A gas in a cylinder receives 500 kJ of heat and does 200 kJ of work on the piston.

ΔU = Q − W = 500 − 200 = 300 kJ

Worked Example 2: Steam Turbine (SFEE)

Answer: 6 MW of power. Steam enters a turbine at 10 kg/s with h₁ = 3,200 kJ/kg and leaves with h₂ = 2,600 kJ/kg. Heat loss and changes in kinetic and potential energy are negligible.

W = ṁ(h₁ − h₂) = 10 × (3,200 − 2,600) = 6,000 kW = 6 MW

Applying SFEE to Common Devices

Device Simplified energy equation
Turbine (adiabatic) w = h₁ − h₂
Compressor/pump w_in = h₂ − h₁
Boiler/heat exchanger q = h₂ − h₁
Nozzle V₂ = √(2(h₁ − h₂) + V₁²)
Throttle valve h₁ = h₂

Corollaries

  • Internal energy is a property (depends only on state).

  • Energy of an isolated system is constant.

  • A perpetual motion machine of the first kind (producing work without any energy input) is impossible.

Limitation

The first law tells us how much energy is converted but not the direction of processes or how much heat can be turned into work; that is the role of the second law.

3

State the Kelvin-Planck and Clausius statements of the second law.

The second law of thermodynamics sets the direction of natural processes and the limits on converting heat into work. The Kelvin-Planck statement: it is impossible for any device operating in a cycle to receive heat from a single reservoir and produce an equal amount of work; in other words, no heat engine can be 100% efficient, since some heat must be rejected to a colder reservoir. The Clausius statement: it is impossible to construct a device that, operating in a cycle, transfers heat from a colder body to a hotter body with no other effect, so a refrigerator needs work input.

Read full answer

Applies toMechanical engineering (thermodynamics)

Kelvin-Planck Statement (Heat Engines)

  • A heat engine must exchange heat with at least two reservoirs: it takes Q_H from a hot source and rejects Q_L to a cold sink.

  • Thermal efficiency: η = W / Q_H = 1 − Q_L / Q_H < 1.

  • A device that violates it is a perpetual motion machine of the second kind (PMM2).

Clausius Statement (Refrigerators and Heat Pumps)

  • Heat flows naturally from hot to cold; moving it from cold to hot needs external work.

  • COP of a refrigerator: Q_L / W, which is finite.

Equivalence

The two statements are equivalent: violating one implies violating the other. For example, a “work-free” refrigerator combined with a normal heat engine would act as a single-reservoir engine, violating Kelvin-Planck.

Worked Example: Checking an Inventor’s Claim

Answer: the claim is impossible, since 75% exceeds the Carnot limit of 70%. An inventor claims an engine working between 1,000 K and 300 K has an efficiency of 75%.

  • Maximum possible (Carnot) efficiency = 1 − T_L / T_H = 1 − 300 / 1,000 = 70%

  • Claimed 75% > 70% → violates the second law

Consequences of the Second Law

  • Introduces entropy and the principle that entropy of an isolated system never decreases.

  • Sets the Carnot efficiency as the upper limit for heat engines.

  • Defines the absolute thermodynamic temperature scale.

  • Explains why real processes are irreversible (friction, heat transfer across finite temperature differences, mixing).

Practical Meaning

  • Power plants must reject heat to condensers and cooling towers; thermal efficiencies of about 33–45% (coal) or about 55–62% (combined cycle) reflect this limit plus real losses.

  • Refrigerators and air conditioners need electrical power to move heat out of a cold space.

4

What is entropy?

Entropy (S) is a thermodynamic property that measures the degree of molecular disorder or randomness of a system, and quantifies how much of its energy is unavailable for doing work. For a reversible process, the change in entropy equals the heat transferred divided by the absolute temperature: dS = δQ_rev / T. Its unit is J/K (specific entropy in J/kg·K).

Read full answer

Applies toMechanical engineering (thermodynamics)

Key Principles

  • Entropy is a state property (depends only on the state, not the path).

  • Clausius inequality: ∮ δQ / T ≤ 0 (equals zero for reversible cycles).

  • Increase of entropy principle: for an isolated system, ΔS ≥ 0; it stays constant for reversible processes and increases for irreversible ones.

  • Entropy can decrease locally (e.g. when a system is cooled), but the total entropy of system plus surroundings always increases in real processes.

Entropy Change Formulas

Process ΔS
Phase change at constant T Q / T = m·L / T
Heating a solid or liquid (constant c) m·c·ln(T₂ / T₁)
Ideal gas (general) m[c_v·ln(T₂/T₁) + R·ln(V₂/V₁)] or m[c_p·ln(T₂/T₁) − R·ln(p₂/p₁)]
Reversible adiabatic (isentropic) 0

Worked Example 1: Melting Ice

Answer: ΔS ≈ 1.223 kJ/K. 1 kg of ice melts at 0 °C (latent heat 334 kJ/kg).

ΔS = 334 / 273.15 ≈ 1.223 kJ/K

Worked Example 2: Heating Water

Answer: ΔS ≈ 0.779 kJ/K. 1 kg of water (c = 4.186 kJ/kg·K) is heated from 20 °C to 80 °C.

ΔS = 4.186 × ln(353.15 / 293.15) = 4.186 × 0.1862 ≈ 0.779 kJ/K

Uses in Engineering

  • T-s and h-s (Mollier) diagrams for analysing steam turbines, refrigeration cycles and gas turbines.

  • Isentropic efficiency of turbines and compressors: comparing actual work with ideal (constant-entropy) work.

  • Entropy generation analysis to find where losses occur and how much work is lost (lost work = T₀ × S_gen).

Interview Tip

Give both views: the macroscopic definition (dS = δQ_rev/T) and the physical meaning (disorder and unavailable energy), then state that the entropy of an isolated system never decreases.

5

What is the difference between a reversible and an irreversible process?

A reversible process is an idealised process that can be reversed exactly, returning both the system and its surroundings to their original states, with no net change anywhere. It proceeds through a series of equilibrium states (quasi-static) with no friction or other dissipative effects. An irreversible process cannot be reversed without leaving some change in the surroundings; all real processes are irreversible because of friction, heat transfer across finite temperature differences, unrestrained expansion and mixing.

Read full answer

Applies toMechanical engineering (thermodynamics)

Comparison

Aspect Reversible Irreversible
Existence Idealisation All real processes
Speed Infinitely slow (quasi-static) Finite rate
States Passes through equilibrium states Non-equilibrium intermediate states
Entropy generation Zero Positive
Work output (expansion) Maximum possible Less than maximum
Work input (compression) Minimum possible More than minimum
On p-v diagram Can be drawn as a continuous line Path not exactly defined (shown dashed)

Causes of Irreversibility

  • Friction (mechanical and fluid).

  • Heat transfer across a finite temperature difference.

  • Unrestrained (free) expansion.

  • Mixing of different substances.

  • Electrical resistance (I²R heating), hysteresis.

  • Chemical reactions such as combustion.

Worked Example: Entropy Generated by Heat Transfer

Answer: entropy generated ≈ 1.667 kJ/K and lost work ≈ 500 kJ. 1,000 kJ of heat flows directly from a reservoir at 600 K to one at 300 K; the surroundings are at 300 K.

  1. ΔS (hot) = −1,000 / 600 ≈ −1.667 kJ/K

  2. ΔS (cold) = +1,000 / 300 ≈ +3.333 kJ/K

  3. S_gen = 3.333 − 1.667 = 1.667 kJ/K (positive, so irreversible)

  4. Lost work = T₀ × S_gen = 300 × 1.667 ≈ 500 kJ: a Carnot engine between these reservoirs could have produced 500 kJ of work (50% efficiency) from this heat.

Internally vs Externally Reversible

  • Internally reversible: no irreversibility inside the system (e.g. frictionless).

  • Externally reversible: heat exchange with the surroundings at infinitesimal temperature differences.

Why It Matters

Reversible processes set the upper limit of performance (e.g. Carnot efficiency, isentropic turbine work). Engineers measure real equipment against them using isentropic efficiency and second-law (exergy) efficiency.

6

What is the Carnot cycle, and why is no engine more efficient than it?

The Carnot cycle is an ideal, fully reversible heat engine cycle working between two thermal reservoirs at temperatures T_H and T_L. It consists of two reversible isothermal processes and two reversible adiabatic (isentropic) processes. Its efficiency, η = 1 − T_L / T_H, is the highest possible for any engine between those temperatures. This follows from Carnot’s theorem: an engine more efficient than a reversible one would violate the second law.

Read full answer

Applies toMechanical engineering (thermodynamics)

The Four Processes

Process Description Heat/work
1 → 2 Reversible isothermal expansion at T_H Heat Q_H absorbed from source; work done
2 → 3 Reversible adiabatic expansion Temperature falls T_H → T_L; work done
3 → 4 Reversible isothermal compression at T_L Heat Q_L rejected to sink; work input
4 → 1 Reversible adiabatic compression Temperature rises T_L → T_H; work input

On a T-s diagram, the cycle is a rectangle: net work = (T_H − T_L) × Δs.

Efficiency

η_Carnot = W_net / Q_H = 1 − Q_L / Q_H = 1 − T_L / T_H (temperatures in kelvin)

Worked Example

Answer: 50% efficiency, 400 kJ of work and 400 kJ rejected. A Carnot engine works between 600 K and 300 K and receives 800 kJ of heat.

  1. η = 1 − 300 / 600 = 0.50 (50%)

  2. W = 0.5 × 800 = 400 kJ

  3. Q_L = 800 − 400 = 400 kJ

Why No Engine Is More Efficient (Carnot’s Theorem)

  1. Suppose engine X is more efficient than a reversible engine R between the same reservoirs.

  2. Run R backwards as a refrigerator, driven by part of X’s work.

  3. X produces more work than R needs, for the same heat exchanged with the hot reservoir.

  4. The combined system would then produce net work while exchanging heat with only the cold reservoir, violating the Kelvin-Planck statement.

  5. Therefore no engine can be more efficient than a reversible engine, and all reversible engines between the same two temperatures have the same efficiency.

Why the Carnot Cycle Is Not Used in Practice

  • Isothermal heat transfer is extremely slow.

  • Isentropic processes need perfectly frictionless, insulated machines.

  • Very large cylinder volumes and low net work per cycle (with gases).

  • With steam, compressing a wet mixture is impractical.

Real cycles (Rankine, Brayton, Otto, Diesel) are compared with the Carnot cycle as a benchmark. To raise efficiency, raise T_H (better materials) or lower T_L (better condensers).

7

What is the efficiency of a Carnot engine working between 527°C and 27°C?

Answer: the Carnot efficiency is 62.5%. Convert the temperatures to kelvin, then apply η = 1 − T_L / T_H.

Read full answer

Applies toMechanical engineering (thermodynamics)

Step-by-Step Solution

  1. Convert to kelvin (using 273 for simplicity):

  2. T_H = 527 + 273 = 800 K

  3. T_L = 27 + 273 = 300 K

  4. Apply the Carnot formula:

  5. η = 1 − T_L / T_H = 1 − 300 / 800 = 1 − 0.375 = 0.625

  6. Efficiency = 62.5%

(Using 273.15: η = 1 − 300.15 / 800.15 ≈ 62.49%, which rounds to the same answer.)

What It Means

If the engine receives 1,000 kJ of heat from the source: - Work output = 0.625 × 1,000 = 625 kJ - Heat rejected to the sink = 1,000 − 625 = 375 kJ

This is the maximum any engine could achieve between these temperatures; a real engine would achieve much less because of friction and other irreversibilities.

Common Mistake

Using Celsius directly: 1 − 27/527 ≈ 94.9%, which is wrong. Thermodynamic formulas always need absolute temperatures (kelvin).

How to Increase the Efficiency

Change New efficiency
Raise T_H to 1,000 K (727 °C), T_L = 300 K 1 − 300/1,000 = 70%
Lower T_L to 250 K, T_H = 800 K 1 − 250/800 = 68.75%

Lowering T_L by 50 K raises efficiency more than raising T_H by 50 K would (1 − 300/850 ≈ 64.7%), but in practice T_L is limited by the environment (cooling water or air temperature).

Related Results

  • Refrigerator COP between the same temperatures: T_L / (T_H − T_L) = 300 / 500 = 0.6.

  • Heat pump COP: T_H / (T_H − T_L) = 800 / 500 = 1.6.

8

What is the difference between the Otto cycle and the Diesel cycle?

The Otto cycle is the ideal air-standard cycle for spark-ignition (petrol) engines: heat is added at constant volume. The Diesel cycle is the ideal cycle for compression-ignition (diesel) engines: heat is added at constant pressure. For the same compression ratio, the Otto cycle is more efficient, but diesel engines use much higher compression ratios, so in practice they achieve higher efficiency.

Read full answer

Applies toMechanical engineering (thermodynamics and IC engines)

Processes

Step Otto cycle Diesel cycle
1 → 2 Isentropic compression Isentropic compression
2 → 3 Constant-volume heat addition Constant-pressure heat addition
3 → 4 Isentropic expansion Isentropic expansion
4 → 1 Constant-volume heat rejection Constant-volume heat rejection

Efficiency Formulas

  • Otto: η = 1 − 1 / r^(γ−1)

  • Diesel: η = 1 − [1 / r^(γ−1)] × [(ρ^γ − 1) / (γ(ρ − 1))]

r = compression ratio, ρ = cut-off ratio (V₃/V₂), γ = 1.4 for air. The bracketed term in the Diesel formula is always greater than 1, so Diesel efficiency is lower at the same r.

Worked Example

Answer: Otto at r = 8 ≈ 56.5%; Diesel at r = 18 and ρ = 2 ≈ 63.2%; Otto at r = 18 would be ≈ 68.5%.

  1. Otto, r = 8: 8^0.4 ≈ 2.297 → η = 1 − 1/2.297 ≈ 56.5%

  2. Diesel, r = 18, ρ = 2:

  3. 18^0.4 ≈ 3.178

  4. (2^1.4 − 1) / (1.4 × 1) = (2.639 − 1) / 1.4 ≈ 1.171

  5. η = 1 − 1.171 / 3.178 ≈ 1 − 0.368 ≈ 63.2%

  6. Otto at r = 18 (for comparison): η = 1 − 1/3.178 ≈ 68.5% (impossible in practice, because petrol would knock)

Comparison

Aspect Otto Diesel
Engine type Petrol (SI) Diesel (CI)
Heat addition Constant volume Constant pressure
Typical compression ratio About 8–12 About 14–22
Efficiency at same r Higher Lower
Actual efficiency Lower (limited r) Higher
Ignition Spark plug Heat of compression

Dual (Mixed) Cycle

Real high-speed diesel engines are better modelled by the dual cycle, with heat added partly at constant volume and partly at constant pressure.

9

What is the difference between a 2-stroke and a 4-stroke engine?

A 4-stroke engine completes its cycle (intake, compression, power, exhaust) in four piston strokes, i.e. two crankshaft revolutions, giving one power stroke every two revolutions. A 2-stroke engine completes the cycle in two strokes, i.e. one revolution, giving one power stroke every revolution, by combining intake and exhaust with compression and expansion using ports and scavenging.

Read full answer

Applies toMechanical engineering (IC engines)

Comparison

Aspect 2-stroke 4-stroke
Power strokes One per revolution One per two revolutions
Valves Usually ports (no valve train) Inlet and exhaust valves, camshaft
Power-to-weight ratio Higher Lower
Fuel efficiency Lower (fresh charge lost in scavenging) Higher
Emissions Higher HC (unburnt fuel), oil burnt with fuel Lower
Lubrication Oil mixed with fuel (petrol 2-strokes) Separate sump and oil pump
Torque smoothness Smoother (more power strokes) Needs heavier flywheel
Construction and cost Simple, cheap More complex
Wear and life Faster wear Longer life
Cooling Harder (more frequent combustion) Easier
Typical uses Older scooters and motorcycles, chainsaws, outboard motors, very large marine diesel engines Cars, motorcycles, trucks, generators

Worked Example: Indicated Power

Answer: about 18.85 kW for the 4-stroke and about 37.7 kW (theoretical) for a 2-stroke of the same size. A single-cylinder engine has bore 100 mm, stroke 120 mm, indicated mean effective pressure 8 bar and speed 3,000 rpm.

  1. Piston area A = π/4 × 0.1² ≈ 0.007854 m²

  2. Swept volume = A × L = 0.007854 × 0.12 ≈ 0.000942 m³ (942 cc)

  3. Power strokes per second (4-stroke) = 3,000 / 2 / 60 = 25

  4. IP = p_m × L × A × n = 8 × 10⁵ × 0.000942 × 25 ≈ 18,850 W ≈ 18.85 kW

  5. 2-stroke: 50 power strokes per second → about 37.7 kW in theory; in practice, poorer scavenging gives a much smaller gain (often about 1.3–1.5 times).

Why 2-Strokes Declined in Vehicles

Emission norms (BS-II onwards in India) made small petrol 2-strokes uncompetitive due to high HC emissions and oil smoke. However, large slow-speed 2-stroke diesel engines (with uniflow scavenging) remain the most efficient engines for ship propulsion, reaching about 50% efficiency.

10

What is the difference between a petrol (SI) engine and a diesel (CI) engine?

A petrol (spark-ignition, SI) engine draws in a premixed air-fuel mixture, compresses it moderately (compression ratio about 8–12) and ignites it with a spark plug, working on the Otto cycle. A diesel (compression-ignition, CI) engine compresses only air to a high pressure and temperature (compression ratio about 14–22), then injects fuel, which ignites by itself from the heat of compression, working on the Diesel (or dual) cycle. Diesels are more efficient and produce more torque; petrol engines are lighter, smoother and rev higher.

Read full answer

Applies toMechanical engineering (IC engines)

Comparison

Aspect Petrol (SI) Diesel (CI)
Ideal cycle Otto Diesel / dual
Fuel Petrol (high self-ignition temperature, volatile) Diesel (low self-ignition temperature)
Mixture formation Outside or inside cylinder (carburettor, port or direct injection) Fuel injected into hot compressed air
Ignition Spark plug Heat of compression
Compression ratio About 8–12 About 14–22
Load control Throttle (quantity of mixture) Amount of fuel injected (no throttle)
Thermal efficiency About 25–35% About 35–45%
Weight Lighter Heavier (stronger build)
Speed range Higher rpm Lower rpm, more low-end torque
Noise and vibration Lower Higher
Emissions concern CO, HC, NOx (three-way catalytic converter) NOx and particulate matter (SCR, DPF)
Cost Lower Higher

Worked Example: Brake Thermal Efficiency From BSFC

Answer: about 38.5% for the diesel and about 29.2% for the petrol engine. A diesel engine has a brake specific fuel consumption (BSFC) of 220 g/kWh with fuel calorific value 42,500 kJ/kg; a petrol engine has 280 g/kWh with 44,000 kJ/kg.

  • η = 3,600 / (BSFC in kg/kWh × CV in kJ/kg)

  • Diesel: 3,600 / (0.220 × 42,500) = 3,600 / 9,350 ≈ 38.5%

  • Petrol: 3,600 / (0.280 × 44,000) = 3,600 / 12,320 ≈ 29.2%

Why Diesels Are More Efficient

  • Higher compression ratio → higher expansion ratio.

  • No throttling losses at part load.

  • Lean overall air-fuel ratio.

Typical Uses

  • Petrol: two-wheelers, small cars, generators, lawn mowers.

  • Diesel: trucks, buses, tractors, locomotives, ships, large generators, earth-moving equipment.

Emission Norms

In India, BS-VI (from April 2020) brought both closer: petrol engines use direct injection and catalytic converters, while diesels need DPF (diesel particulate filter) and SCR with urea (AdBlue/DEF) to meet NOx and PM limits.

11

What is compression ratio, and why do diesel engines have a higher one?

Compression ratio ® is the ratio of the total cylinder volume when the piston is at bottom dead centre to the clearance volume when it is at top dead centre: r = (V_s + V_c) / V_c. A higher compression ratio raises thermal efficiency. Diesel engines need a much higher ratio (about 14–22) because they rely on the heat of compression to ignite the fuel, while petrol engines are limited to about 8–12 by knocking.

Read full answer

Applies toMechanical engineering (IC engines)

Formula

  • Swept volume V_s = (π/4) × D² × L

  • r = (V_s + V_c) / V_c = 1 + V_s / V_c

Worked Example 1: Calculating r

Answer: r ≈ 10. An engine has bore 80 mm, stroke 90 mm and clearance volume 50 cc.

  1. V_s = (π/4) × 8² × 9 cm³ ≈ 50.27 × 9 ≈ 452.4 cc

  2. r = (452.4 + 50) / 50 ≈ 10.05

Worked Example 2: Temperature at End of Compression

Answer: about 953 K (680 °C) in a diesel at r = 18, versus about 754 K (481 °C) for air at r = 10. Air at 300 K is compressed isentropically (γ = 1.4).

  • Diesel, r = 18: T₂ = 300 × 18^0.4 ≈ 300 × 3.178 ≈ 953 K

  • r = 10: T₂ = 300 × 10^0.4 ≈ 300 × 2.512 ≈ 754 K

Diesel fuel’s self-ignition temperature is only about 210–250 °C, so the air at the end of compression is hot enough to ignite the injected fuel reliably, even in cold weather and at idle (real temperatures are somewhat lower than ideal because of heat loss, which is why higher ratios help cold starting).

Why Petrol Engines Cannot Use High Ratios

  • The air-petrol mixture is already in the cylinder during compression.

  • Too high a ratio heats the end gas enough to self-ignite before the flame reaches it, causing knock.

  • Petrol’s octane number sets the practical limit (about 10–12 with direct injection and knock sensors; some modern engines reach about 13–14).

Why Diesels Benefit

  • Only air is compressed, so there is no knock risk during compression.

  • Higher r gives higher efficiency (more expansion of gases).

  • Limits on diesel r: peak pressure (heavier construction), NOx emissions, and friction losses at very high r.

Effect on Efficiency (Otto, γ = 1.4)

r η = 1 − 1/r^0.4
6 51.2%
8 56.5%
10 60.2%
12 63.0%
12

What is knocking in SI engines, and how is it prevented?

Knocking (detonation) in a spark-ignition engine is the auto-ignition of the unburnt end-gas ahead of the flame front, before the normal flame reaches it. The sudden, uncontrolled combustion creates pressure waves that hit the cylinder walls, producing a metallic pinging sound, power loss, overheating and possible damage to pistons, rings and spark plugs. It is prevented by using higher-octane fuel, lowering the compression ratio or retarding ignition timing, improving cooling and designing combustion chambers for fast, controlled burning.

Read full answer

Applies toMechanical engineering (IC engines)

How Knock Happens

  1. Spark ignites the mixture; a flame front travels across the chamber.

  2. Burning gases expand and compress the remaining unburnt mixture (end gas).

  3. If the end gas reaches its self-ignition temperature for long enough before the flame arrives, it ignites spontaneously.

  4. Rapid pressure rise and pressure waves cause knock.

Effects

  • Loud metallic noise.

  • Loss of power and efficiency.

  • Overheating of the piston crown, valves and spark plug.

  • Damage: pitted or holed pistons, broken rings, head gasket failure.

Factors and Remedies

Factor Increases knock Prevention
Fuel octane number Low octane Use higher-octane fuel (RON 95, 98, ethanol blends)
Compression ratio High r Lower r, or use knock sensors to adjust timing
Ignition timing Too advanced Retard timing
Intake temperature and pressure Hot, high boost Intercooling, lower boost
Engine temperature Hot cylinder walls Good cooling system
Combustion chamber Long flame travel, hot spots Compact chamber, central spark plug, squish, swirl, turbulence
Mixture strength Near-stoichiometric to slightly lean at high load Slightly richer mixture at full load
Deposits Carbon deposits raise effective r and form hot spots Clean combustion chambers

Worked Example: What Octane Number Means

Answer: an RON 91 fuel resists knock like a mixture of 91% iso-octane and 9% n-heptane. Iso-octane is assigned 100 and n-heptane 0; a fuel’s octane number is the percentage of iso-octane in the reference blend that knocks at the same intensity in a standard CFR test engine.

In India, regular petrol is about RON 91, premium grades about 95–100, and E20 (20% ethanol) blends have a higher octane rating because ethanol’s octane is about 108.

Modern Knock Control

Engines use knock sensors (piezoelectric accelerometers on the block). When knock is detected, the ECU retards ignition timing for that cylinder, then gradually advances it again. This lets engines run close to the knock limit for best efficiency.

Knock vs Pre-Ignition

Pre-ignition is ignition before the spark by a hot spot; knock happens after the spark, in the end gas. Pre-ignition can lead to severe knock.

13

What is the function of a carburettor and a fuel injector?

A carburettor and a fuel injector both supply fuel to an engine and mix it with air in the right proportion. A carburettor uses the pressure drop of air flowing through a venturi to draw fuel from a float chamber, mechanically metering the mixture. A fuel injector is an electronically controlled valve that sprays fuel under pressure into the intake port or directly into the cylinder, with the quantity set precisely by the engine control unit (ECU) using sensor data.

Read full answer

Applies toMechanical engineering (IC engines)

Carburettor Working

  1. Air flows through a venturi; its velocity rises and pressure falls (Bernoulli).

  2. The pressure difference draws fuel from the float chamber through a jet.

  3. The fuel atomises and mixes with air.

  4. A throttle valve controls the mixture quantity (engine power).

  5. Extra circuits: choke (rich mixture for cold start), idle circuit, accelerator pump, economiser.

Fuel Injection Types

Type Where fuel is injected Use
Throttle body injection (TBI) At the throttle body (single point) Early injection cars
Multi-point fuel injection (MPFI) Into each intake port Most petrol cars and BS-VI motorcycles
Gasoline direct injection (GDI) Directly into the cylinder at high pressure Modern efficient petrol engines
Common rail direct injection (CRDI) Directly into diesel cylinders at very high pressure (about 1,600–2,500 bar) Modern diesel engines

Worked Example: Fuel Flow Needed

Answer: about 2.1 g/s, or about 7.5 kg/h of petrol. A 1.2-litre four-stroke petrol engine runs at 3,000 rpm with volumetric efficiency 85%, air density 1.2 kg/m³ and stoichiometric air-fuel ratio 14.7:1.

  1. Air volume per second = 0.0012 m³ × (3,000 / 2 / 60) = 0.0012 × 25 = 0.03 m³/s

  2. Actual air volume = 0.03 × 0.85 = 0.0255 m³/s

  3. Air mass = 0.0255 × 1.2 ≈ 0.0306 kg/s

  4. Fuel = 0.0306 / 14.7 ≈ 0.00208 kg/s ≈ 2.1 g/s ≈ 7.5 kg/h

Comparison

Aspect Carburettor Fuel injection
Metering Mechanical (venturi, jets) Electronic (ECU, sensors)
Accuracy Approximate, changes with altitude and temperature Precise, adapts automatically
Cold starting Choke needed Automatic enrichment
Fuel economy Lower Higher
Emissions Higher; hard to meet modern norms Low, works with catalytic converters (closed loop with O₂ sensor)
Cost and maintenance Low cost, simple to tune Higher cost, needs diagnostic tools

Why Carburettors Were Phased Out

Indian BS-VI emission norms (2020) effectively required fuel injection for new two-wheelers and cars, because carburettors cannot control the mixture precisely enough for catalytic converters and OBD requirements.

14

What is a turbocharger, and how is it different from a supercharger?

A turbocharger and a supercharger both force more air into an engine (forced induction) so that more fuel can be burnt, increasing power from the same engine size. A turbocharger is driven by a turbine powered by exhaust gases, using energy that would otherwise be wasted. A supercharger is driven mechanically by the crankshaft (belt or gears), so it responds instantly but takes some engine power to run.

Read full answer

Applies toMechanical engineering (IC engines)

Comparison

Aspect Turbocharger Supercharger
Drive Exhaust gas turbine Crankshaft (belt, chain or gears)
Energy source Waste exhaust energy Engine power (parasitic loss)
Efficiency Higher overall Lower
Response Turbo lag at low rpm (reduced by twin-scroll, VGT, small turbos) Instant boost
Boost at low rpm Low Good
Heat High (hot turbine side) Lower
Complexity Needs oil and cooling supply, wastegate Simpler installation
Typical use Most modern diesel and downsized petrol cars, trucks, generators, ships Performance cars, some older racing engines

Key Components (Turbocharger)

  • Turbine (exhaust side) and compressor (intake side) on a common shaft, spinning at up to about 100,000–250,000 rpm.

  • Wastegate or variable geometry turbine (VGT) to control boost.

  • Intercooler to cool compressed air (raises density, reduces knock).

  • Blow-off valve (petrol) to relieve pressure when the throttle closes.

Worked Example: Effect of Boost and Intercooling

Answer: air density rises about 1.55 times without intercooling and about 1.88 times with intercooling to 320 K. Intake air at 1 bar and 300 K is compressed to 2 bar (absolute) with compressor efficiency 75% (γ = 1.4).

  1. Ideal outlet temperature: T₂s = 300 × 2^0.286 ≈ 300 × 1.219 ≈ 365.7 K

  2. Actual: T₂ = 300 + (365.7 − 300) / 0.75 ≈ 300 + 87.6 ≈ 387.6 K

  3. Density ratio without intercooler = (2 / 1) × (300 / 387.6) ≈ 1.55

  4. With intercooler to 320 K: (2 / 1) × (300 / 320) ≈ 1.88

So intercooling gives about 21% more air mass for the same boost, as well as reducing knock risk in petrol engines.

Benefits of Turbocharging

  • Downsizing: a smaller turbo engine can match a larger naturally aspirated one, saving fuel.

  • Better performance at high altitude.

  • Higher torque at low and medium rpm in modern designs.

Electric Superchargers and E-Turbos

Newer systems use an electric motor to spin the compressor (or assist the turbocharger shaft), eliminating lag, especially in 48 V mild-hybrid and racing applications.

15

What is the Rankine cycle?

The Rankine cycle is the ideal thermodynamic cycle for steam power plants. Water is pumped to high pressure, heated in a boiler into steam, expanded in a turbine to produce work, and condensed back to water in a condenser. It is a practical alternative to the Carnot cycle because the working fluid is pumped as a liquid (needing very little work) and heat is added at constant pressure.

Read full answer

Applies toMechanical engineering (thermodynamics and power plants)

The Four Processes

Process Component Description
1 → 2 Turbine Isentropic expansion of steam, producing work
2 → 3 Condenser Constant-pressure heat rejection; steam condenses to saturated liquid
3 → 4 Feed pump Isentropic compression of liquid to boiler pressure
4 → 1 Boiler (and superheater) Constant-pressure heat addition to form superheated steam

Formulas

  • Turbine work: W_t = h₁ − h₂

  • Pump work: W_p = h₄ − h₃ ≈ v·(p₄ − p₃)

  • Heat supplied: Q_in = h₁ − h₄

  • Efficiency: η = (W_t − W_p) / Q_in

  • Steam rate = 3,600 / W_net (kg/kWh)

Worked Example

Answer: efficiency ≈ 35.3% and steam rate ≈ 3.38 kg/kWh. Steam enters the turbine at 40 bar and 400 °C (h₁ ≈ 3,214 kJ/kg, s₁ ≈ 6.769 kJ/kg·K) and the condenser is at 0.1 bar (h_f ≈ 191.8, h_fg ≈ 2,392.8 kJ/kg, s_f ≈ 0.649, s_fg ≈ 7.501 kJ/kg·K, v_f ≈ 0.00101 m³/kg).

  1. Dryness after expansion: x₂ = (6.769 − 0.649) / 7.501 ≈ 0.816

  2. h₂ = 191.8 + 0.816 × 2,392.8 ≈ 2,144 kJ/kg

  3. W_t = 3,214 − 2,144 = 1,070 kJ/kg

  4. W_p = 0.00101 × (4,000 − 10) ≈ 4.0 kJ/kg → h₄ ≈ 195.8 kJ/kg

  5. W_net = 1,070 − 4 = 1,066 kJ/kg

  6. Q_in = 3,214 − 195.8 ≈ 3,018 kJ/kg

  7. η = 1,066 / 3,018 ≈ 35.3%; steam rate = 3,600 / 1,066 ≈ 3.38 kg/kWh

Ways to Improve Efficiency

  • Higher boiler pressure and temperature (supercritical and ultra-supercritical plants above 221 bar and about 600 °C).

  • Lower condenser pressure (better vacuum).

  • Reheat: expand steam partly, reheat it, then expand further (also improves dryness at turbine exit).

  • Regenerative feed heating: bleed steam heats feedwater, raising mean temperature of heat addition.

Practical Concern

Exhaust steam dryness should not fall much below about 0.88–0.90, as water droplets erode turbine blades; superheating and reheating keep it dry enough.

16

What is the Brayton cycle?

The Brayton (Joule) cycle is the ideal thermodynamic cycle for gas turbines used in aircraft jet engines and gas-based power plants. Air is compressed isentropically, heated at constant pressure in a combustion chamber, expanded isentropically through a turbine, and (in the ideal closed cycle) cooled at constant pressure. Its efficiency depends mainly on the pressure ratio: η = 1 − 1 / r_p^((γ−1)/γ).

Read full answer

Applies toMechanical engineering (thermodynamics and gas turbines)

Processes

Process Component Description
1 → 2 Compressor Isentropic compression
2 → 3 Combustion chamber Constant-pressure heat addition
3 → 4 Turbine Isentropic expansion
4 → 1 Exhaust / cooler Constant-pressure heat rejection

Worked Example

Answer: efficiency ≈ 48.2%, net work ≈ 398 kJ/kg and back work ratio ≈ 0.41. Air enters the compressor at 300 K, pressure ratio r_p = 10, turbine inlet temperature 1,400 K (γ = 1.4, c_p = 1.005 kJ/kg·K).

  1. Temperature ratio = 10^0.2857 ≈ 1.931

  2. T₂ = 300 × 1.931 ≈ 579.2 K; T₄ = 1,400 / 1.931 ≈ 725.1 K

  3. Compressor work = 1.005 × (579.2 − 300) ≈ 280.6 kJ/kg

  4. Turbine work = 1.005 × (1,400 − 725.1) ≈ 678.3 kJ/kg

  5. Net work = 678.3 − 280.6 ≈ 397.7 kJ/kg

  6. Heat supplied = 1.005 × (1,400 − 579.2) ≈ 824.9 kJ/kg

  7. η = 397.7 / 824.9 ≈ 48.2% (check: 1 − 1/1.931 ≈ 48.2%)

  8. Back work ratio = 280.6 / 678.3 ≈ 0.41: about 41% of turbine work drives the compressor, so component efficiencies matter greatly

Improvements

  • Regeneration: exhaust heat preheats compressed air (useful when T₄ > T₂).

  • Intercooling between compressor stages: reduces compression work.

  • Reheating between turbine stages: increases turbine work.

  • Higher turbine inlet temperature: advanced alloys, blade cooling and thermal barrier coatings (modern turbines exceed about 1,500–1,600 °C).

  • Combined cycle: hot exhaust (about 550–650 °C) raises steam for a Rankine cycle, giving overall efficiencies of about 55–62%.

Applications

Aircraft engines (turbojet, turbofan, turboprop), gas-based power plants (open and combined cycle), marine propulsion, and gas compressor drives in pipelines.

17

What do the boiler, condenser and cooling tower do in a thermal plant?

In a thermal power plant, the boiler burns fuel to turn feedwater into high-pressure, high-temperature steam for the turbine. The condenser condenses the exhaust steam from the turbine back into water under vacuum, so it can be pumped back to the boiler and the turbine can expand steam to a very low pressure. The cooling tower removes the heat absorbed by the condenser cooling water, rejecting it to the atmosphere mainly by evaporation, so the cooling water can be reused.

Read full answer

Applies toMechanical engineering (thermal power plants)

Comparison

Aspect Boiler Condenser Cooling tower
Function Generates steam Condenses turbine exhaust steam Cools the condenser cooling water
Heat flow Heat added (from fuel) Heat removed from steam to cooling water Heat rejected from water to air
Pressure High (e.g. 170–250+ bar) Vacuum (about 0.08–0.1 bar abs) Atmospheric
Main parts Furnace, water walls, drum (subcritical), superheater, reheater, economiser, air preheater Shell and tube heat exchanger, hotwell, air extraction (ejectors or vacuum pumps) Fill media, fans (induced/forced draft) or natural draft shell, drift eliminators, basin
Fluid Water/steam Steam (shell side), cooling water (tube side) Cooling water and ambient air

Why the Condenser Matters

  • Lower exhaust pressure increases turbine work and cycle efficiency.

  • Recovers pure condensate (expensive treated water) for reuse.

  • Removes non-condensable gases that would raise pressure and cause corrosion.

Worked Example: Cooling Water Needed

Answer: about 5,500 kg/s of cooling water, and roughly 300–345 m³/h of water lost to evaporation. A condenser receives 100 kg/s of exhaust steam, each kg releasing about 2,300 kJ as it condenses; the cooling water temperature rise (range) is 10 °C.

  1. Heat rejected = 100 × 2,300 = 230,000 kW = 230 MW

  2. Cooling water flow = 230,000 / (4.186 × 10) ≈ 5,494 kg/s (about 19,800 m³/h)

  3. Evaporation if all this heat left by evaporation (latent heat ≈ 2,400 kJ/kg) ≈ 230,000 / 2,400 ≈ 96 kg/s ≈ 345 m³/h. In practice, part of the heat leaves as sensible heat to the air, so actual evaporation is somewhat lower; blowdown and drift add to make-up water needs.

Types of Cooling Towers

  • Natural draft (hyperbolic concrete shells): large plants, no fans.

  • Mechanical draft (induced or forced draft fans): compact, common in industry.

  • Dry (air-cooled) condensers: used where water is scarce, with an efficiency penalty.

Interview Tip

Tie them together: boiler makes steam → turbine uses it → condenser turns it back to water → cooling tower rejects the condenser heat. Then explain why vacuum in the condenser improves efficiency.

18

What are the three modes of heat transfer?

Heat is transferred in three ways: conduction, the transfer of heat through a material by molecular vibration and free electrons, without bulk motion; convection, transfer between a surface and a moving fluid by combined conduction and fluid motion; and radiation, transfer by electromagnetic waves, which needs no medium and works even in a vacuum.

Read full answer

Applies toMechanical engineering (heat transfer)

Governing Laws

Mode Law Equation
Conduction Fourier’s law Q = k·A·ΔT / L
Convection Newton’s law of cooling Q = h·A·(T_s − T_∞)
Radiation Stefan-Boltzmann law Q = ε·σ·A·(T_s⁴ − T_surr⁴)

k = thermal conductivity (W/m·K), h = convective heat transfer coefficient (W/m²·K), ε = emissivity, σ = 5.67 × 10⁻⁸ W/m²·K⁴.

Worked Examples

Answer: conduction 700 W, convection 500 W, radiation ≈ 612 W.

  1. Conduction through a 10 m² brick wall 0.2 m thick (k = 0.7 W/m·K) with 20 °C difference: Q = 0.7 × 10 × 20 / 0.2 = 700 W

  2. Convection from a 1 m² surface at 70 °C to air at 20 °C with h = 10 W/m²·K: Q = 10 × 1 × 50 = 500 W

  3. Radiation from a 1 m² surface at 100 °C (373 K), ε = 0.9, to surroundings at 20 °C (293 K): Q = 0.9 × 5.67 × 10⁻⁸ × (373⁴ − 293⁴) = 0.9 × 5.67 × 10⁻⁸ × 1.199 × 10¹⁰ ≈ 612 W

Everyday and Engineering Examples

Mode Examples
Conduction Heat through engine cylinder walls, insulation, frying pan handle
Convection Radiator in a car, air conditioning coils, boiling water, cooling fins with fans
Radiation Sun heating the earth, furnace walls, boiler radiant section, IR heaters

Combined Modes

Most real problems involve more than one mode, for example: - A boiler: radiation and convection from flue gases to tubes, conduction through tube walls, convection (boiling) to water. - A building wall: convection outside, conduction through layers, convection inside, plus solar radiation.

These are combined using the thermal resistance approach (resistances in series and parallel), with an overall heat transfer coefficient U.

19

What is Fourier's law of heat conduction?

Fourier’s law states that the rate of heat conduction through a material is proportional to the area normal to the heat flow and to the temperature gradient in that direction: Q = −k·A·(dT/dx). The negative sign shows that heat flows from higher to lower temperature. The constant k is the material’s thermal conductivity (W/m·K).

Read full answer

Applies toMechanical engineering (heat transfer)

For a Plane Wall (Steady State, Constant k)

Q = k·A·(T₁ − T₂) / L

This can be written as Q = ΔT / R, where R = L / (k·A) is the conduction thermal resistance (K/W), analogous to electrical resistance (Ohm’s law).

Composite Walls

  • Layers in series: R_total = Σ L_i / (k_i·A)

  • Including convection on both sides: R_total = 1/(h_i·A) + Σ L/(k·A) + 1/(h_o·A)

Worked Example: Effect of Insulation

Answer: heat loss falls from 70 W/m² to about 13 W/m², an 81% reduction. A 0.2 m brick wall (k = 0.7 W/m·K) has a 20 °C temperature difference across it. A 50 mm layer of insulation (k = 0.04 W/m·K) is added (convection resistances ignored for simplicity). Per 1 m²:

  1. Brick only: R = 0.2 / 0.7 ≈ 0.286 K/W → Q = 20 / 0.286 = 70 W

  2. With insulation: R = 0.286 + 0.05 / 0.04 = 0.286 + 1.25 = 1.536 K/W → Q = 20 / 1.536 ≈ 13.0 W

  3. Reduction ≈ (70 − 13) / 70 ≈ 81%

Cylinder (Pipe) Conduction

For a pipe of length L with inner radius r₁ and outer radius r₂:

Q = 2π·k·L·(T₁ − T₂) / ln(r₂ / r₁)

For insulating small pipes and wires, adding insulation can initially increase heat loss until the critical radius r_c = k / h is exceeded.

Assumptions

  • One-dimensional heat flow.

  • Steady state (temperatures do not change with time).

  • Homogeneous, isotropic material.

  • Constant thermal conductivity (or use an average value).

For transient conduction, the heat diffusion equation is used: ∂T/∂t = α·∇²T, where α = k / (ρ·c_p) is thermal diffusivity.

Applications

Insulation design for buildings, pipes and cold stores; heat sinks; furnace walls; engine cylinder design; thermal analysis of electronics.

20

What is thermal conductivity?

Thermal conductivity (k) is a material property that measures how well a material conducts heat. It is the rate of heat flow through a unit area of a material of unit thickness when there is a unit temperature difference across it. Its SI unit is W/m·K. Metals have high conductivity (good conductors), while gases, foams and fibrous materials have low conductivity (good insulators).

Read full answer

Applies toMechanical engineering (heat transfer and materials)

Definition (From Fourier’s Law)

k = Q·L / (A·ΔT)

Typical Values (Near Room Temperature)

Material k (W/m·K)
Diamond About 1,000–2,000
Silver About 429
Copper About 385–400
Aluminium About 205–237
Carbon steel About 45–54
Stainless steel About 15–16
Concrete About 1.0–1.8
Brick About 0.6–0.8
Glass About 0.8–1.0
Water About 0.6
Wood About 0.1–0.2
Glass wool / rock wool About 0.03–0.045
PUF (polyurethane foam) About 0.02–0.03
Air (still) About 0.026

Worked Example

Answer: copper conducts 16 kW and steel 2 kW. Heat flows through a 5 mm thick plate of area 0.1 m² with a 2 °C temperature difference.

  • Copper (k = 400): Q = 400 × 0.1 × 2 / 0.005 = 16,000 W

  • Carbon steel (k = 50): Q = 50 × 0.1 × 2 / 0.005 = 2,000 W

Copper conducts eight times as much heat, which is why heat exchanger tubes, radiators and heat sinks use copper or aluminium.

Factors Affecting Thermal Conductivity

  • Material structure: free electrons in metals carry heat efficiently; in non-metals, lattice vibrations (phonons) carry heat.

  • Temperature: k of most pure metals decreases with temperature; for gases and many insulators it increases.

  • Purity and alloying: alloys conduct less than pure metals (stainless steel vs carbon steel).

  • Density and porosity: trapped air lowers k (insulation materials).

  • Moisture: wet insulation conducts much more heat, so vapour barriers are important.

Applications

  • High k: heat exchangers, engine cooling fins, electronic heat sinks, cooking utensils.

  • Low k: building insulation, refrigerator walls (PUF), pipe lagging, furnace linings, thermal protection systems.

21

What is the difference between natural and forced convection?

Natural (free) convection is heat transfer in which fluid motion is caused only by buoyancy forces: fluid near a hot surface becomes less dense and rises, and cooler fluid replaces it. Forced convection is heat transfer in which fluid is moved over the surface by an external device such as a fan, pump or blower (or by vehicle motion). Forced convection gives much higher heat transfer coefficients.

Read full answer

Applies toMechanical engineering (heat transfer)

Comparison

Aspect Natural convection Forced convection
Cause of flow Density differences (buoyancy) Fan, pump, blower, wind
Velocity Low Higher, controllable
Typical h (air) About 2–25 W/m²·K About 25–250 W/m²·K
Typical h (water) About 50–1,000 W/m²·K About 100–20,000 W/m²·K
Governing numbers Grashof (Gr), Rayleigh (Ra = Gr·Pr) Reynolds (Re), Prandtl (Pr)
Correlation form Nu = C·(Gr·Pr)ⁿ Nu = C·Reᵐ·Prⁿ (e.g. Dittus-Boelter: Nu = 0.023·Re^0.8·Pr^0.4)
Energy use None for fluid motion Fan or pump power needed
Examples Room heater, transformer oil cooling (ONAN), passive heat sinks, hot water rising in a solar heater Car radiator, AC coils, CPU fan, boiler economiser, air-cooled condensers

Worked Example

Answer: 250 W with natural convection and 2,500 W with forced convection. A 1 m² surface at 80 °C is exposed to air at 30 °C, with h = 5 W/m²·K (still air) or 50 W/m²·K (fan-blown air).

  • Natural: Q = 5 × 1 × (80 − 30) = 250 W

  • Forced: Q = 50 × 1 × 50 = 2,500 W

A tenfold increase in h gives ten times the heat transfer for the same surface and temperature difference, which is why fans are added to heat sinks and radiators.

Dimensionless Numbers

  • Nusselt (Nu = hL/k): ratio of convective to conductive heat transfer.

  • Grashof (Gr = gβΔT·L³/ν²): ratio of buoyancy to viscous forces.

  • Reynolds (Re = VL/ν): ratio of inertia to viscous forces.

  • Prandtl (Pr = ν/α): ratio of momentum to thermal diffusivity.

Mixed Convection

When both effects are comparable (roughly Gr/Re² ≈ 1), as in low-speed flows over hot surfaces, both must be considered.

Design Choice

Natural convection is silent, reliable and needs no power, but needs larger surfaces. Forced convection allows compact equipment but needs energy and maintenance for fans and pumps.

22

What is a heat exchanger? How do parallel and counter flow differ?

A heat exchanger is a device that transfers heat between two or more fluids at different temperatures, usually separated by a solid wall so they do not mix. In parallel flow, both fluids enter at the same end and flow in the same direction. In counter flow, they enter at opposite ends and flow in opposite directions. Counter flow is more effective: it gives a higher mean temperature difference, so it needs less area, and the cold fluid can leave hotter than the hot fluid’s outlet.

Read full answer

Applies toMechanical engineering (heat transfer)

Types of Heat Exchangers

Type Examples
Double pipe (tube in tube) Small duties, oil coolers
Shell and tube Power plant condensers, refinery coolers, feedwater heaters
Plate heat exchanger (PHE) Dairy, HVAC, food processing (compact, easy cleaning)
Finned tube / compact Car radiators, AC evaporators and condensers
Regenerators Rotary air preheaters, Cowper stoves
Direct contact Cooling towers, deaerators

Parallel vs Counter Flow

Aspect Parallel flow Counter flow
Flow direction Same Opposite
Temperature difference Large at inlet, small at outlet More uniform along the length
LMTD Lower Higher
Cold fluid outlet Always below hot fluid outlet Can exceed hot fluid outlet
Area needed More Less
Thermal stress at inlet Higher Lower
Use When rapid initial cooling or limited wall temperature is needed Most industrial applications

Worked Example

Answer: counter flow needs about 2.88 m² and parallel flow about 3.58 m² (about 25% more). Hot oil cools from 150 °C to 90 °C while water heats from 30 °C to 70 °C; Q = 100 kW and U = 500 W/m²·K.

Counter flow: - ΔT₁ = 150 − 70 = 80 °C; ΔT₂ = 90 − 30 = 60 °C - LMTD = (80 − 60) / ln(80/60) ≈ 20 / 0.2877 ≈ 69.5 °C - A = 100,000 / (500 × 69.5) ≈ 2.88 m²

Parallel flow: - ΔT₁ = 150 − 30 = 120 °C; ΔT₂ = 90 − 70 = 20 °C - LMTD = (120 − 20) / ln(120/20) ≈ 100 / 1.792 ≈ 55.8 °C - A = 100,000 / (500 × 55.8) ≈ 3.58 m²

Design Considerations

Fouling (scale and deposits add resistance, so a fouling factor is included), pressure drop and pumping power, cleaning access, material compatibility (corrosion), and thermal expansion.

23

What is LMTD?

LMTD (log mean temperature difference) is the effective average temperature difference between the hot and cold fluids in a heat exchanger. Because the temperature difference changes along the length of the exchanger, a simple arithmetic mean is inaccurate; the logarithmic mean gives the correct driving force for heat transfer: Q = U·A·LMTD.

Read full answer

Applies toMechanical engineering (heat transfer)

Formula

LMTD = (ΔT₁ − ΔT₂) / ln(ΔT₁ / ΔT₂)

  • Counter flow: ΔT₁ = T_h,in − T_c,out; ΔT₂ = T_h,out − T_c,in

  • Parallel flow: ΔT₁ = T_h,in − T_c,in; ΔT₂ = T_h,out − T_c,out

  • If ΔT₁ = ΔT₂, LMTD = ΔT (the formula gives 0/0, so use the limit).

For shell and tube or cross-flow exchangers, multiply the counter-flow LMTD by a correction factor F (F ≤ 1, from charts).

Worked Example

Answer: LMTD ≈ 65.5 °C and the required area is about 3.84 m². Steam condenses at 120 °C and heats 2 kg/s of water from 20 °C to 80 °C (c_p = 4.186 kJ/kg·K), with U = 2,000 W/m²·K.

  1. Q = 2 × 4.186 × (80 − 20) ≈ 502.3 kW

  2. ΔT₁ = 120 − 20 = 100 °C; ΔT₂ = 120 − 80 = 40 °C (same for parallel and counter flow because the steam temperature is constant)

  3. LMTD = (100 − 40) / ln(100/40) = 60 / 0.9163 ≈ 65.5 °C

  4. A = 502,300 / (2,000 × 65.5) ≈ 3.84 m²

Using the arithmetic mean (70 °C) would underestimate the area (about 3.59 m²), so the exchanger would fall short of the duty.

Why Logarithmic?

In a heat exchanger, the temperature difference decays approximately exponentially along the length. Integrating dQ = U·ΔT·dA under that condition gives the logarithmic mean.

LMTD vs Effectiveness-NTU Method

Method Best used when
LMTD All four inlet and outlet temperatures are known (sizing problems)
ε-NTU Outlet temperatures are unknown (rating an existing exchanger)

Assumptions

  • Steady state, constant U and specific heats.

  • No heat loss to the surroundings.

  • No phase change in the middle of the exchanger (unless at constant temperature, as above).

24

What is a black body, and what is the Stefan-Boltzmann law?

A black body is an idealised surface that absorbs all incident radiation at every wavelength and direction (absorptivity = 1) and, at a given temperature, emits the maximum possible radiation (emissivity = 1). The Stefan-Boltzmann law states that the total radiant energy emitted per unit area of a black body is proportional to the fourth power of its absolute temperature: E_b = σ·T⁴, where σ = 5.67 × 10⁻⁸ W/m²·K⁴.

Read full answer

Applies toMechanical engineering (heat transfer, radiation)

Key Laws of Radiation

Law Statement
Stefan-Boltzmann E_b = σ·T⁴ (black body); E = ε·σ·T⁴ (real/grey body)
Wien’s displacement λ_max × T = 2,898 µm·K
Kirchhoff’s law For a body in thermal equilibrium, emissivity = absorptivity (ε = α) at each wavelength
Planck’s law Gives spectral distribution of black body emission

Net Radiation Between a Body and Its Surroundings

Q = ε·σ·A·(T_s⁴ − T_surr⁴) (small grey body in large surroundings)

Worked Example

Answer: a black body at 1,000 K emits about 56.7 kW/m², with peak emission near 2.9 µm.

  1. E_b = 5.67 × 10⁻⁸ × 1,000⁴ = 5.67 × 10⁻⁸ × 10¹² = 56,700 W/m²

  2. λ_max = 2,898 / 1,000 ≈ 2.9 µm (infrared)

  3. A real oxidised steel surface with ε = 0.8 emits 0.8 × 56.7 ≈ 45.4 kW/m²

  4. Doubling T to 2,000 K increases emission 16 times (2⁴), to about 907 kW/m²

A human body at about 310 K peaks at 2,898 / 310 ≈ 9.3 µm, which is why thermal cameras work in the 8–14 µm band.

Real Surfaces

Surface Approximate emissivity
Polished aluminium 0.03–0.05
Polished copper 0.03–0.05
Oxidised steel 0.7–0.9
Brick, concrete 0.85–0.95
Paint (any colour, IR) 0.85–0.95
Human skin About 0.98

Practical Approximations of a Black Body

  • A small hole in a large cavity (nearly all radiation entering is absorbed).

  • Lamp black and special black coatings (emissivity about 0.95–0.98).

Applications

Furnace and boiler design, solar collectors (selective coatings with high absorptivity, low emissivity), radiation shields, spacecraft thermal control, IR thermometers and thermal imaging (which need correct emissivity settings).

25

What is the vapour compression refrigeration cycle?

The vapour compression refrigeration (VCR) cycle is the most widely used refrigeration cycle, found in refrigerators, air conditioners and chillers. A refrigerant absorbs heat from the cold space by evaporating at low pressure, is compressed to high pressure and temperature, rejects heat to the surroundings while condensing, and passes through an expansion device that drops its pressure before it returns to the evaporator.

Read full answer

Applies toMechanical engineering (refrigeration and air conditioning)

Four Components and Processes

Process Component What happens
1 → 2 Compressor Low-pressure vapour compressed (ideally isentropic) to high-pressure superheated vapour; work input
2 → 3 Condenser Heat rejected; vapour desuperheats and condenses to high-pressure liquid
3 → 4 Expansion valve / capillary tube Throttling at constant enthalpy (h₃ = h₄); pressure and temperature fall
4 → 1 Evaporator Low-pressure liquid-vapour mixture absorbs heat from the space and evaporates

Key Formulas (Per kg of Refrigerant)

  • Refrigerating effect: RE = h₁ − h₄

  • Compressor work: W = h₂ − h₁

  • Heat rejected: Q_c = h₂ − h₃

  • COP = RE / W

  • Refrigerant mass flow = cooling capacity / RE

  • 1 TR (ton of refrigeration) = 3.517 kW

Worked Example

Answer: COP ≈ 4.67, mass flow ≈ 0.025 kg/s and compressor power ≈ 0.75 kW per TR. A cycle has h₁ = 395 kJ/kg (evaporator exit), h₂ = 425 kJ/kg (compressor exit) and h₃ = h₄ = 255 kJ/kg (illustrative values for a typical refrigerant).

  1. RE = 395 − 255 = 140 kJ/kg

  2. W = 425 − 395 = 30 kJ/kg

  3. COP = 140 / 30 ≈ 4.67

  4. For 1 TR: ṁ = 3.517 / 140 ≈ 0.0251 kg/s

  5. Power = 0.0251 × 30 ≈ 0.75 kW per TR (ideal; real systems need more because of compressor inefficiency)

Practical Features

  • Subcooling the liquid after the condenser increases refrigerating effect.

  • Superheating the vapour at evaporator exit protects the compressor from liquid.

  • Expansion devices: capillary tubes (domestic), thermostatic expansion valves (TXV), electronic expansion valves (EEV, inverter systems).

  • Compressors: reciprocating, rotary, scroll, screw, centrifugal.

Applications

Household refrigerators, split and window ACs, cold storages, chillers for buildings, vehicle air conditioning, and heat pumps.

26

What is COP (coefficient of performance)?

COP (coefficient of performance) measures the performance of refrigerators, air conditioners and heat pumps: the ratio of useful heat moved to the work (energy) input. For a refrigerator, COP_R = Q_L / W (heat removed from the cold space per unit work); for a heat pump, COP_HP = Q_H / W (heat delivered to the warm space per unit work). Unlike efficiency, COP is usually greater than 1.

Read full answer

Applies toMechanical engineering (refrigeration and heat pumps)

Key Relations

  • Q_H = Q_L + W, so COP_HP = COP_R + 1 (for the same operating conditions)

  • Carnot (maximum) COP:

  • COP_R,max = T_L / (T_H − T_L)

  • COP_HP,max = T_H / (T_H − T_L)

Worked Example 1: Carnot Limit

Answer: maximum COP = 5.36. An AC has its evaporator at −5 °C (268 K) and its condenser at 45 °C (318 K).

  • COP_R,max = 268 / (318 − 268) = 268 / 50 = 5.36

  • COP_HP,max = 318 / 50 = 6.36 (= 5.36 + 1)

Worked Example 2: Real Air Conditioner

Answer: COP ≈ 3.3. A 1.5-ton split AC delivers 5.275 kW of cooling while drawing 1.6 kW.

COP = 5.275 / 1.6 ≈ 3.3 (equivalent to an EER of 3.3 W/W)

Factors Affecting COP

  • Temperature lift: COP falls as the difference between evaporator and condenser temperatures increases. Setting an AC to 24 °C instead of 20 °C improves COP noticeably.

  • Condenser cleanliness and airflow: dirty coils raise condensing temperature and reduce COP.

  • Compressor efficiency: inverter compressors run efficiently at part load.

  • Refrigerant and system design.

Ratings Used in India

  • EER = cooling capacity (W) / power input (W) at one rating condition.

  • ISEER (Indian seasonal energy efficiency ratio) = total annual cooling / total annual energy, used in BEE star labels for ACs (typical 5-star inverter split ACs have ISEER above about 5).

Interview Tip

Explain why COP can exceed 1: a heat pump moves heat rather than creating it, so it can deliver several kW of heat for each kW of electricity, within the Carnot limit.

27

What refrigerants are used today, and why were CFCs phased out?

CFCs (chlorofluorocarbons) such as R-11 and R-12 were phased out under the Montreal Protocol (1987) because the chlorine they release in the stratosphere destroys the ozone layer, which shields the earth from harmful UV radiation. They were replaced first by HCFCs (like R-22, also being phased out), then by HFCs (R-134a, R-410A, R-32), which do not deplete ozone but have high global warming potential (GWP). The Kigali Amendment (2016) now phases down HFCs, pushing the industry towards low-GWP refrigerants: R-32, HFOs (R-1234yf, R-1234ze), and natural refrigerants (R-290 propane, R-600a isobutane, R-744 CO₂, R-717 ammonia).

Read full answer

Applies toMechanical engineering (refrigeration and air conditioning)

Refrigerant Generations

Generation Examples ODP GWP (100-year, approx.) Status
CFC R-11, R-12 High (about 1) About 4,750–10,900 Banned
HCFC R-22 Low (0.055) About 1,810 Being phased out (India’s full phase-out by 2030)
HFC R-134a 0 About 1,430 Being phased down (Kigali)
HFC blend R-410A 0 About 2,090 Being phased down
HFC (lower GWP) R-32 0 About 675 Widely used in split ACs
HFO R-1234yf, R-1234ze 0 Below 1 to about 7 Car ACs, chillers
Natural R-290 (propane), R-600a (isobutane) 0 About 3 Refrigerators, some ACs (flammable)
Natural R-744 (CO₂) 0 1 Supermarkets, heat pumps (high pressure)
Natural R-717 (ammonia) 0 0 Industrial cold storage (toxic)

Worked Example: Impact of a Leak

Answer: a 1 kg leak of R-410A equals about 2,090 kg of CO₂, while the same leak of R-32 equals about 675 kg and of R-290 about 3 kg.

CO₂-equivalent = mass leaked × GWP.

Choosing a Refrigerant

Consider ODP and GWP, thermodynamic performance (COP, capacity), safety class (ASHRAE 34: A1 non-toxic non-flammable, A2L mildly flammable like R-32, A3 highly flammable like R-290, B2L toxic mildly flammable like ammonia), operating pressure, compatibility with oils and materials, cost and availability.

Indian Context

India’s ACs largely use R-32 and R-410A, refrigerators largely R-600a, and India’s HCFC Phase-out Management Plan and India Cooling Action Plan guide the move to low-GWP, efficient cooling.

Interview Tip

Mention both ozone depletion (Montreal) and global warming (Kigali), and name R-32 and R-290/R-600a as current examples.

28

What is the difference between a refrigerator and a heat pump?

A refrigerator and a heat pump both use the same thermodynamic cycle (usually vapour compression) to move heat from a cold region to a hot region using work input. The difference is the purpose: a refrigerator aims to remove heat from a cold space (keep it cold), while a heat pump aims to deliver heat to a warm space (keep it warm). So their performance is measured differently: COP_R = Q_L / W and COP_HP = Q_H / W = COP_R + 1.

Read full answer

Applies toMechanical engineering (refrigeration and heat pumps)

Comparison

Aspect Refrigerator / AC Heat pump
Useful effect Heat removed from cold space (Q_L) Heat supplied to warm space (Q_H)
COP Q_L / W Q_H / W = COP_R + 1
Cold reservoir Space being cooled Outdoor air, ground or water
Hot reservoir Outdoor/room air Space or water being heated
Examples Fridge, freezer, split AC (cooling mode) Heat pump water heater, reverse-cycle AC in heating mode, ground-source heat pump

Worked Example

Answer: the heat pump uses about 2.86 kW of electricity, saving about 7.14 kW (71%) compared with an electric resistance heater. A heat pump with COP 3.5 delivers 10 kW of heat.

  1. Electrical input = 10 / 3.5 ≈ 2.86 kW

  2. Heat taken from the outdoor air = 10 − 2.86 ≈ 7.14 kW

  3. A resistance heater (COP = 1) would need 10 kW

Reverse-Cycle Air Conditioners

A four-way reversing valve swaps the roles of the indoor and outdoor coils, so the same unit cools in summer and heats in winter. Common in hot-and-cold climates (e.g. North India “hot and cold” inverter ACs).

Applications of Heat Pumps

  • Hot water: heat pump water heaters (about 3–4 times more efficient than electric geysers).

  • Space heating in cold regions.

  • Industrial heating up to about 80–120 °C (drying, process water, dairy).

  • Simultaneous heating and cooling (e.g. hotels: chilled water and hot water from one machine).

Limitations

Heat pump COP falls as outdoor temperature drops (larger temperature lift), so air-source units may need backup heaters in very cold climates; ground-source units are more stable.

29

What is the difference between dry bulb, wet bulb and dew point temperature?

Dry bulb temperature (DBT) is the ordinary air temperature measured by a thermometer shielded from radiation and moisture. Wet bulb temperature (WBT) is the temperature shown by a thermometer whose bulb is covered with a wet wick and exposed to moving air; evaporation cools it, so it is lower than DBT unless the air is saturated. Dew point temperature (DPT) is the temperature at which air becomes saturated when cooled at constant pressure and moisture content, so water vapour starts to condense.

Read full answer

Applies toMechanical engineering (psychrometry and air conditioning)

Relationship

  • For unsaturated air: DBT > WBT > DPT

  • For saturated air (100% RH): DBT = WBT = DPT

  • Wet bulb depression = DBT − WBT (larger in dry air)

  • Dew point depression = DBT − DPT

Worked Example

Answer: RH ≈ 61% and dew point ≈ 21.6 °C. Air at sea level has DBT = 30 °C and WBT = 24 °C. Saturation pressures are 4.246 kPa at 30 °C and 2.985 kPa at 24 °C.

  1. Vapour pressure (Carrier/psychrometer equation): p_v ≈ p_sat(WBT) − 0.000662 × p × (DBT − WBT) = 2.985 − 0.000662 × 101.325 × 6 ≈ 2.985 − 0.402 ≈ 2.58 kPa

  2. RH = 2.58 / 4.246 ≈ 61%

  3. Dew point: the temperature where p_sat = 2.58 kPa, which lies between 21 °C (2.487 kPa) and 22 °C (2.645 kPa) → about 21.6 °C

In practice, these values are read directly from a psychrometric chart.

Measurement

  • DBT and WBT: sling psychrometer or aspirated psychrometer (air speed about 3–5 m/s over the wet bulb).

  • DPT: chilled mirror hygrometer, or calculated from DBT and RH by digital sensors.

Engineering Uses

Quantity Use
DBT Sensible heat load, comfort, thermostat control
WBT Cooling tower performance (approach to WBT), evaporative cooler limits, heat stress
DPT Condensation on cold surfaces (ducts, pipes, walls), dehumidification, compressed air dryers

Practical Examples

  • A cooling tower cannot cool water below the ambient wet bulb temperature; good towers get within about 3–5 °C of it (approach).

  • Chilled water pipes at 7 °C will “sweat” in rooms with DPT above 7 °C unless insulated with a vapour barrier.

  • Desert coolers work well in dry climates (large wet bulb depression) and poorly in humid ones.

30

What is relative humidity?

Relative humidity (RH, φ) is the ratio of the actual partial pressure of water vapour in air to the saturation vapour pressure at the same temperature, expressed as a percentage: φ = p_v / p_sat × 100%. It tells how close the air is to being saturated: 100% RH means the air holds as much water vapour as it can at that temperature, and condensation begins.

Read full answer

Applies toMechanical engineering (psychrometry and HVAC)

Related Terms

  • Specific humidity (humidity ratio, ω): mass of water vapour per kg of dry air: ω = 0.622 × p_v / (p − p_v)

  • Absolute humidity: mass of water vapour per m³ of air.

  • Degree of saturation: ω / ω_sat (close to RH at normal conditions).

Effect of Temperature

Saturation pressure rises steeply with temperature, so: - Heating air without adding moisture lowers RH. - Cooling air without removing moisture raises RH until it reaches 100% at the dew point.

Worked Example

Answer: RH = 60% at 25 °C, rising to about 92% if cooled to 18 °C; specific humidity ≈ 0.0119 kg/kg. Room air at 25 °C has a vapour pressure of 1.9 kPa (p_sat at 25 °C = 3.169 kPa; at 18 °C = 2.064 kPa; total pressure 101.325 kPa).

  1. RH = 1.9 / 3.169 ≈ 60%

  2. Cooled to 18 °C with the same moisture: RH = 1.9 / 2.064 ≈ 92%

  3. ω = 0.622 × 1.9 / (101.325 − 1.9) ≈ 1.182 / 99.43 ≈ 0.0119 kg water per kg dry air (about 11.9 g/kg)

Comfort and Industrial Ranges

Application Typical RH
Human comfort About 40–60%
Data centres About 40–60% (ASHRAE allows a wider dew-point range)
Hospitals (operating theatres) About 50–60%
Textile mills About 50–85% (higher to reduce yarn breakage and static)
Pharmaceutical clean rooms Often 30–50%

Effects of Wrong RH

  • Too high: discomfort, mould, corrosion, condensation, poor drying of products.

  • Too low: dry skin and eyes, static electricity, shrinkage and cracking of wood and paper.

Control Methods

  • Dehumidification by cooling coils (cool below dew point, then reheat if needed), desiccant dehumidifiers.

  • Humidification by steam humidifiers, evaporative pads or atomisers.

31

What is Bernoulli's equation, and what are its assumptions?

Bernoulli’s equation states that, along a streamline in steady, incompressible, frictionless flow, the sum of pressure energy, kinetic energy and potential energy per unit weight of fluid is constant: p/(ρg) + V²/(2g) + z = constant. Each term is a “head” in metres. It is the energy conservation principle for flowing fluids and underlies flow meters, pitot tubes, nozzles and many pipe-flow calculations.

Read full answer

Applies toMechanical engineering (fluid mechanics)

Terms

  • p/(ρg): pressure head

  • V²/(2g): velocity head

  • z: elevation (datum) head

  • Sum: total head (H)

For real flow between points 1 and 2 with losses and pumps or turbines: p₁/ρg + V₁²/2g + z₁ + h_pump = p₂/ρg + V₂²/2g + z₂ + h_turbine + h_loss

Assumptions

  1. Steady flow (no change with time).

  2. Incompressible fluid (constant density).

  3. Inviscid (frictionless) flow: no viscous losses.

  4. Along a streamline (or irrotational flow for the whole field).

  5. No shaft work or heat transfer between the points.

Worked Example: Venturimeter

Answer: about 50 litres per second. Water flows through a venturimeter with inlet diameter 200 mm and throat diameter 100 mm. The pressure difference is 20 kPa and the discharge coefficient is 0.98.

  1. A₁ = π/4 × 0.2² ≈ 0.03142 m²; A₂ = π/4 × 0.1² ≈ 0.007854 m²; A₁/A₂ = 4

  2. Continuity: V₁ = V₂ / 4

  3. Bernoulli: V₂² − V₁² = 2Δp/ρ = 2 × 20,000 / 1,000 = 40 → V₂²(1 − 1/16) = 40 → V₂ ≈ 6.53 m/s

  4. Ideal Q = 0.007854 × 6.53 ≈ 0.0513 m³/s

  5. Actual Q = 0.98 × 0.0513 ≈ 0.0503 m³/s ≈ 50 L/s

Applications

  • Flow meters: venturimeter, orifice meter, flow nozzle.

  • Pitot tube: measures velocity from stagnation pressure (V = √(2Δp/ρ)); used in aircraft speed indicators.

  • Carburettor venturi, atomisers and spray guns.

  • Siphons, flow from tanks (Torricelli: V = √(2gh)).

  • Aerofoil lift (pressure difference explanation, together with momentum principles).

Limitations

Not valid for highly viscous flow, flow with significant friction (unless losses are added), compressible gas flow at high speed (Mach above about 0.3), or across pumps and turbines without work terms.

32

What is the difference between laminar and turbulent flow?

In laminar flow, fluid moves in smooth, parallel layers with no mixing between them; viscous forces dominate and the flow is orderly and predictable. In turbulent flow, fluid particles move irregularly with eddies and strong mixing; inertia forces dominate. The Reynolds number decides which occurs: in pipes, flow is generally laminar below Re ≈ 2,000, turbulent above about 4,000, and transitional in between.

Read full answer

Applies toMechanical engineering (fluid mechanics)

Comparison

Aspect Laminar Turbulent
Reynolds number (pipe) Below about 2,000 Above about 4,000
Particle motion Smooth layers, straight paths Random, eddies, cross-mixing
Velocity profile in pipe Parabolic; V_max = 2 × V_avg Flatter; V_max ≈ 1.2 × V_avg
Friction factor f = 64 / Re (Darcy), independent of roughness Depends on Re and relative roughness (Moody chart, Colebrook)
Head loss Proportional to V Roughly proportional to V^1.75–V²
Heat and mass transfer Low High (good mixing)
Examples Oil in small pipes, blood in capillaries, slow honey flow Water in household pipes, rivers, air over vehicles, smoke far from a cigarette

Worked Example

Answer: the flow is laminar at 0.04 m/s (Re = 2,000, f = 0.032) and turbulent at 1 m/s (Re = 50,000). Water (ν = 1.0 × 10⁻⁶ m²/s) flows in a 50 mm pipe.

  1. At V = 0.04 m/s: Re = 0.04 × 0.05 / 10⁻⁶ = 2,000 → laminar (just at the limit); f = 64 / 2,000 = 0.032

  2. At V = 1 m/s: Re = 1 × 0.05 / 10⁻⁶ = 50,000 → turbulent

Most practical water flows in pipes are turbulent.

Head Loss (Darcy-Weisbach)

h_f = f × (L/D) × V² / (2g)

Practical Importance

  • Pipe design: turbulent flow needs more pumping power, but mixes better.

  • Heat exchangers: turbulence (baffles, fins, high velocity) increases heat transfer.

  • Lubrication: bearings rely on laminar oil films.

  • Aerodynamics: laminar boundary layers have lower skin friction; turbulent ones resist separation (dimples on golf balls).

  • Chemical mixing: turbulent flow mixes fluids quickly.

33

What is Reynolds number, and what does it tell you?

Reynolds number (Re) is a dimensionless number that is the ratio of inertia forces to viscous forces in a flowing fluid: Re = ρVD / µ = VD / ν. It tells you whether the flow will be laminar (low Re, viscous forces dominate) or turbulent (high Re, inertia dominates), and it is used to choose friction factors, heat transfer correlations and to scale models.

Read full answer

Applies toMechanical engineering (fluid mechanics)

Terms

  • ρ = density (kg/m³), V = mean velocity (m/s), D = characteristic length (pipe diameter, m)

  • µ = dynamic viscosity (Pa·s), ν = µ/ρ = kinematic viscosity (m²/s)

  • For non-circular ducts, use hydraulic diameter D_h = 4A / P (A = flow area, P = wetted perimeter).

Flow Regimes

Situation Laminar Transitional Turbulent
Pipe flow Re < 2,000 (about 2,300) 2,000–4,000 Re > 4,000
Flat plate boundary layer Re_x < about 5 × 10⁵ — Above about 5 × 10⁵
Open channel (Re based on hydraulic radius) Below about 500 500–2,000 Above about 2,000

Worked Example

Answer: water flow is turbulent (Re = 200,000), the oil flow is laminar (Re = 2,000), and water becomes laminar only below about 0.02 m/s.

  1. Water (ν ≈ 1.0 × 10⁻⁶ m²/s) in a 100 mm pipe at 2 m/s: Re = 2 × 0.1 / 10⁻⁶ = 200,000 → turbulent

  2. Oil (ν = 1.0 × 10⁻⁴ m²/s) in the same pipe at 2 m/s: Re = 2 × 0.1 / 10⁻⁴ = 2,000 → laminar

  3. Critical velocity for water in this pipe: V = Re × ν / D = 2,000 × 10⁻⁶ / 0.1 = 0.02 m/s

What Reynolds Number Tells You

  • Flow regime (laminar or turbulent).

  • Friction factor in pipes: f = 64/Re for laminar; Moody chart or Colebrook equation for turbulent.

  • Heat transfer: Nusselt number correlations (e.g. Dittus-Boelter for Re > 10,000).

  • Drag coefficient on spheres, cylinders and vehicles.

  • Similarity in model testing: wind tunnel and towing tank models must match Re (often along with Mach or Froude numbers) to represent full-size behaviour.

Interview Tip

Give the formula, the meaning (inertia vs viscous), the pipe flow limits (2,000 / 4,000), and one example calculation; that covers what most interviewers ask.

34

What is viscosity? How do dynamic and kinematic viscosity differ?

Viscosity is a fluid’s resistance to flow, or more precisely its resistance to shear deformation, caused by internal friction between fluid layers. Dynamic (absolute) viscosity (µ) relates shear stress to the velocity gradient (τ = µ·du/dy, Newton’s law of viscosity) and is measured in Pa·s. Kinematic viscosity (ν) is dynamic viscosity divided by density (ν = µ / ρ), measured in m²/s; it describes how quickly momentum diffuses through the fluid.

Read full answer

Applies toMechanical engineering (fluid mechanics)

Units

Quantity SI unit CGS unit Conversion
Dynamic viscosity µ Pa·s (N·s/m²) Poise (P) 1 P = 0.1 Pa·s; 1 cP = 1 mPa·s
Kinematic viscosity ν m²/s Stokes (St) 1 St = 10⁻⁴ m²/s; 1 cSt = 10⁻⁶ m²/s

Typical Values (About 20 °C)

Fluid µ (Pa·s) ν (m²/s)
Air 1.8 × 10⁻⁵ 1.5 × 10⁻⁵
Water 1.0 × 10⁻³ 1.0 × 10⁻⁶ (1 cSt)
Engine oil (SAE 30, approx.) 0.1–0.3 1–3 × 10⁻⁴
Glycerine About 1.4 About 1.1 × 10⁻³
Honey About 2–10 —

Worked Example

Answer: oil ν ≈ 114 cSt, and the shear stress on the plate is 50 Pa. Engine oil has µ = 0.1 Pa·s and ρ = 880 kg/m³. A plate moves at 0.5 m/s over a 1 mm oil film.

  1. ν = 0.1 / 880 ≈ 1.136 × 10⁻⁴ m²/s ≈ 114 cSt

  2. Velocity gradient = 0.5 / 0.001 = 500 s⁻¹

  3. τ = 0.1 × 500 = 50 Pa (a 1 m² plate needs 50 N to keep moving)

Effect of Temperature

  • Liquids: viscosity decreases as temperature rises (molecular cohesion weakens). Engine oil thins when hot, which is why multigrade oils (e.g. 10W-40) are used.

  • Gases: viscosity increases with temperature (more molecular collisions).

Newtonian vs Non-Newtonian Fluids

  • Newtonian: µ constant regardless of shear rate (water, air, most oils).

  • Non-Newtonian: µ changes with shear rate, e.g. paints and ketchup (shear-thinning), cornflour slurry (shear-thickening), toothpaste (Bingham plastic).

Measurement

Capillary viscometers (Ostwald), falling-ball viscometers, rotational viscometers (Brookfield), Saybolt and Redwood viscometers (older oil industry practice).

35

What is cavitation in pumps?

Cavitation in a pump is the formation of vapour bubbles in the liquid where local pressure falls below the liquid’s vapour pressure (usually at the impeller eye, where pressure is lowest), followed by their violent collapse when they move into higher-pressure regions. The collapsing bubbles produce noise, vibration, loss of head and efficiency, and pitting erosion of the impeller and casing.

Read full answer

Applies toMechanical engineering (fluid machinery)

How It Happens

  1. Liquid accelerates into the impeller eye; pressure drops.

  2. If pressure drops below the vapour pressure at that temperature, the liquid boils locally, forming bubbles.

  3. Bubbles travel into higher-pressure zones of the impeller.

  4. They implode, creating micro-jets and shock waves with very high local pressures, which erode metal over time.

Symptoms

  • Crackling noise, “pumping gravel” sound.

  • Vibration.

  • Drop in head, flow and efficiency.

  • Pitted, spongy-looking impeller surfaces (especially at the vane inlet).

Causes

  • Insufficient NPSH available (NPSHa < NPSHr).

  • High suction lift, long or narrow suction pipes, clogged strainers.

  • Hot liquid (high vapour pressure).

  • Operating far to the right of the best efficiency point (high flow).

  • High altitude (lower atmospheric pressure).

Worked Example: Maximum Theoretical Suction Lift

Answer: about 10.1 m in theory for cold water at sea level, but much less in practice. Water at 20 °C has vapour pressure 2.34 kPa; atmospheric pressure is 101.325 kPa.

Maximum lift = (p_atm − p_v) / (ρg) = (101.325 − 2.34) × 1,000 / (1,000 × 9.81) ≈ 10.09 m

After subtracting friction losses, velocity head and the pump’s NPSH required, practical suction lifts are usually limited to about 6–7 m. Hot water or high altitude reduce this further.

Prevention

  • Increase NPSHa: lower the pump or raise the supply tank (flooded suction), shorten and enlarge suction pipes, reduce bends, keep strainers clean.

  • Cool the liquid or pressurise the suction vessel.

  • Operate near the best efficiency point; avoid throttling on the suction side.

  • Select a pump with lower NPSHr (larger eye, inducer, lower speed).

  • Use cavitation-resistant materials (stainless steel, bronze) for impellers.

Related

Cavitation also occurs in hydraulic turbines (assessed with Thoma’s cavitation factor), ship propellers and control valves.

36

What is the difference between a centrifugal pump and a reciprocating pump?

A centrifugal pump is a rotodynamic pump: a rotating impeller adds velocity to the liquid, and the casing converts it to pressure, giving a smooth, continuous flow that varies with the system head. A reciprocating pump is a positive displacement pump: a piston or plunger moving back and forth traps fixed volumes of liquid and forces them out, giving a pulsating flow that stays nearly constant whatever the pressure. Centrifugal pumps suit high flow at moderate head; reciprocating pumps suit low flow at high pressure.

Read full answer

Applies toMechanical engineering (fluid machinery)

Comparison

Aspect Centrifugal Reciprocating
Principle Centrifugal force (kinetic energy → pressure) Positive displacement
Flow Continuous, smooth Pulsating (air vessels smooth it)
Flow vs pressure Flow falls as head rises (H-Q curve) Nearly constant flow regardless of pressure
Discharge Large Small
Pressure (head) Low to medium (multistage for high) High
Priming Required (unless self-priming design) Usually self-priming
Viscous liquids Poor performance Handles well
Suspended solids Handles (with suitable impeller) Valves can be damaged
Efficiency Good at design point Good, including at part load
Size and weight Compact for given flow Bulky
Maintenance Low Higher (valves, packing, crank)
Safety Can run briefly against closed valve Needs relief valve (pressure builds dangerously)
Uses Water supply, HVAC, irrigation, process plants, boiler feed (multistage) Hydraulic testing, dosing, high-pressure washing, oil field mud pumps

Worked Example 1: Centrifugal Pump Power

Answer: about 21 kW of shaft power. A pump delivers 0.05 m³/s (50 L/s) of water against a total head of 30 m with overall efficiency 70%.

P = ρgQH / η = 1,000 × 9.81 × 0.05 × 30 / 0.7 = 14,715 / 0.7 ≈ 21.0 kW

Worked Example 2: Reciprocating Pump Discharge

Answer: about 5.3 L/s theoretical. A single-acting pump has bore 150 mm, stroke 300 mm and runs at 60 rpm.

  1. A = π/4 × 0.15² ≈ 0.01767 m²

  2. Q = A × L × N / 60 = 0.01767 × 0.3 × 60 / 60 ≈ 0.0053 m³/s

  3. If actual discharge is 0.0050 m³/s, slip = (0.0053 − 0.0050) / 0.0053 ≈ 5.7%

Selection Rule

High flow, moderate head, clean or slightly dirty liquid → centrifugal. Low flow, very high pressure, metering or viscous liquid → reciprocating (or other positive displacement types such as gear, screw or diaphragm pumps).

37

What is NPSH?

NPSH (net positive suction head) is the absolute pressure head at the pump suction, above the liquid’s vapour pressure head. NPSH available (NPSHa) depends on the system (tank level, atmospheric pressure, liquid temperature, suction losses). NPSH required (NPSHr) is set by the pump design and given by the manufacturer. To avoid cavitation, NPSHa must exceed NPSHr with a safe margin.

Read full answer

Applies toMechanical engineering (fluid machinery)

NPSH Available

NPSHa = (p_s − p_v) / (ρg) ± h_s − h_f

  • p_s = absolute pressure on the liquid surface (atmospheric for an open tank)

  • p_v = vapour pressure of the liquid at pumping temperature

  • h_s = static height of liquid surface above (+, flooded) or below (−, suction lift) the pump centreline

  • h_f = friction losses in the suction line

Worked Example

Answer: NPSHa ≈ 4.9 m with cold water (safe against NPSHr = 3.5 m) but only about 0.5 m at 80 °C, so the pump would cavitate. A pump lifts water from an open tank 4 m below it, with 1 m of suction friction loss. The vapour pressure is 4.25 kPa at 30 °C and 47.4 kPa at 80 °C (take ρg = 9,810 N/m³).

  1. At 30 °C: (101.325 − 4.25) / 9.81 ≈ 9.90 m → NPSHa = 9.90 − 4 − 1 ≈ 4.9 m

  2. Margin over NPSHr = 4.9 − 3.5 = 1.4 m (ratio about 1.4, acceptable)

  3. At 80 °C: (101.325 − 47.4) / 9.81 ≈ 5.50 m → NPSHa = 5.50 − 4 − 1 ≈ 0.5 m → cavitation

Remedy for hot water: use a flooded suction (put the tank above the pump) or pressurise the tank.

NPSH Required

  • Determined by test: the NPSH at which the pump’s head drops by 3% (NPSH3) at a given flow.

  • Increases with flow rate, so check NPSHr at the maximum expected flow.

  • Recommended margins: often at least 0.5–1 m or a ratio NPSHa/NPSHr of about 1.1–1.5 or more, depending on the application and standards (e.g. ANSI/HI 9.6.1).

Ways to Increase NPSHa

  • Raise the liquid level or lower the pump.

  • Use larger, shorter suction pipes with fewer fittings.

  • Reduce liquid temperature.

  • Pressurise the suction vessel.

  • Keep strainers and foot valves clean.

Ways to Reduce NPSHr

  • Lower pump speed, larger impeller eye, double-suction impellers, inducers.

38

What is the difference between an impulse turbine and a reaction turbine?

In an impulse turbine, all the available head is converted into kinetic energy in nozzles before the water (or steam) strikes the runner, so the pressure stays the same (atmospheric for water turbines) as the jet passes over the blades; the force comes only from the change in jet momentum. In a reaction turbine, the pressure drops partly in fixed guide vanes and partly in the moving runner, so the runner is fully submerged and both pressure and kinetic energy produce force. Examples: the Pelton wheel is an impulse turbine; Francis and Kaplan turbines are reaction turbines.

Read full answer

Applies toMechanical engineering (fluid machinery and power plants)

Comparison

Aspect Impulse Reaction
Energy at runner inlet Only kinetic Pressure + kinetic
Pressure across runner Constant Decreases
Water flow Free jet; runner not full Runner full of water
Degree of reaction 0 Between 0 and 1 (often about 0.5 in steam turbines)
Draft tube Not needed Needed (recovers energy at exit)
Casing Prevents splashing only Must be watertight and pressure-tight
Head High Medium (Francis) to low (Kaplan)
Flow Low Medium to high
Specific speed (single jet Pelton) About 10–35 Francis about 60–300; Kaplan about 300–1,000
Examples (water) Pelton wheel, Turgo Francis, Kaplan, propeller
Examples (steam) De Laval, Curtis stages Parsons turbine

Specific Speed for Selection

N_s = N·√P / H^(5/4) (N in rpm, P in kW, H in m)

Worked Example

Answer: N_s ≈ 28 suits a Pelton wheel; N_s ≈ 249 suits a Francis turbine.

  1. High head site: P = 10,000 kW, H = 400 m, N = 500 rpm

  2. H^1.25 = 400 × 400^0.25 ≈ 400 × 4.472 ≈ 1,789

  3. N_s = 500 × √10,000 / 1,789 = 50,000 / 1,789 ≈ 28 → Pelton (impulse)

  4. Medium head site: P = 10,000 kW, H = 40 m, N = 250 rpm

  5. H^1.25 = 40 × 40^0.25 ≈ 40 × 2.515 ≈ 100.6

  6. N_s = 250 × 100 / 100.6 ≈ 249 → Francis (reaction)

Indian Examples

Pelton wheels in high-head Himalayan plants; Francis turbines in many medium-head dams (e.g. large river projects); Kaplan turbines in low-head run-of-river and barrage plants.

39

What are stress and strain?

Stress is the internal resisting force per unit area that develops in a material when an external load acts on it: σ = P / A, measured in N/m² (Pa), usually MPa (N/mm²). Strain is the deformation per unit original length: ε = δL / L, which is dimensionless. Stress describes how intensely a material is loaded, and strain describes how much it deforms.

Read full answer

Applies toMechanical engineering (strength of materials)

Types of Stress

Type Cause Formula
Tensile Pulling load σ = P / A
Compressive Pushing load σ = P / A
Shear Forces parallel to the surface τ = F / A
Bending Bending moment σ = M·y / I
Torsional shear Twisting τ = T·r / J
Thermal Restrained temperature change σ = E·α·ΔT

Types of Strain

  • Linear (normal) strain: ε = δL / L

  • Lateral strain: change in width / original width

  • Shear strain: angular distortion γ (radians)

  • Volumetric strain: δV / V

Worked Example

Answer: stress ≈ 159 MPa, strain ≈ 0.0008 and elongation ≈ 1.59 mm. A steel rod 20 mm in diameter and 2 m long carries a tensile load of 50 kN (E = 200 GPa).

  1. A = π/4 × 20² ≈ 314.2 mm²

  2. σ = 50,000 / 314.2 ≈ 159.2 MPa

  3. ε = σ / E = 159.2 / 200,000 ≈ 7.96 × 10⁻⁴

  4. δL = ε × L = 7.96 × 10⁻⁴ × 2,000 ≈ 1.59 mm

Engineering Stress vs True Stress

  • Engineering stress uses the original area; true stress uses the actual (reduced) area during deformation.

  • Engineering strain uses original length; true strain = ln(L / L₀).

  • They are almost equal for small strains but differ greatly after necking in a tensile test.

Thermal Stress Example

A steel rail fixed at both ends heated by 30 °C (α = 12 × 10⁻⁶ /°C): σ = 200,000 × 12 × 10⁻⁶ × 30 = 72 MPa (compressive), which is why expansion gaps or long welded rails with controlled stress-free temperatures are used.

Why It Matters

Designers keep working stresses below allowable values (yield or ultimate strength divided by a factor of safety) and check that strains (deflections) are acceptable.

40

What is Hooke's law, and what is Young's modulus?

Hooke’s law states that, within the elastic limit (strictly, the proportional limit), stress is directly proportional to strain: σ = E·ε. The constant of proportionality E is Young’s modulus (modulus of elasticity), which measures a material’s stiffness: its resistance to elastic deformation. A higher E means less deformation under the same stress.

Read full answer

Applies toMechanical engineering (strength of materials)

Related Elastic Constants

Constant Relation Meaning
Young’s modulus E σ / ε (normal stress and strain) Stiffness in tension/compression
Shear modulus (modulus of rigidity) G τ / γ Stiffness in shear
Bulk modulus K Volumetric stress / volumetric strain Resistance to volume change
Poisson’s ratio µ (or ν) Lateral strain / longitudinal strain Lateral contraction

Relations: E = 2G(1 + µ) = 3K(1 − 2µ)

Typical Values of E

Material E (GPa)
Steel About 200–210
Cast iron About 100–170
Aluminium alloys About 69–72
Copper About 110–130
Titanium alloys About 110–120
Concrete About 25–35
Wood (along grain) About 9–15
Rubber About 0.01–0.1

Worked Example: Finding E From a Tensile Test

Answer: E ≈ 204 GPa (consistent with steel). A specimen 10 mm in diameter with 50 mm gauge length extends by 0.0625 mm under 20 kN, within the elastic range.

  1. A = π/4 × 10² ≈ 78.54 mm²

  2. σ = 20,000 / 78.54 ≈ 254.6 MPa

  3. ε = 0.0625 / 50 = 0.00125

  4. E = 254.6 / 0.00125 ≈ 203,700 MPa ≈ 204 GPa

Elongation Formula

From Hooke’s law: δL = P·L / (A·E), used to calculate elongation of rods, bolts and cables.

Limitations of Hooke’s Law

  • Valid only up to the proportional limit.

  • Many materials (rubber, polymers, concrete, cast iron) are non-linear even at low stress.

  • Time-dependent behaviour (creep, viscoelasticity) is not covered.

Engineering Use

E controls deflection and stiffness: beams, shafts, machine frames and springs are often designed for stiffness (limiting deflection) as much as for strength. Note that alloying and heat treatment change strength greatly but barely change E for steels.

41

Explain the stress-strain curve for mild steel.

The stress-strain curve for mild steel, obtained from a tensile test, shows how the material behaves as load increases until fracture. It has a straight elastic region obeying Hooke’s law, a distinct yield point where the steel deforms plastically without much increase in stress, a strain hardening region where stress rises to the ultimate tensile strength (UTS), and a necking region where the cross-section narrows locally until fracture. Mild steel’s clear yield point and large elongation make it ductile and predictable.

Read full answer

Applies toMechanical engineering (strength of materials and materials testing)

Key Points on the Curve

Point / region Meaning
A: Proportional limit End of the straight line; stress ∝ strain (Hooke’s law)
B: Elastic limit Maximum stress with full recovery on unloading (very close to A)
C: Upper yield point Stress at which yielding begins
D: Lower yield point Stress drops and stays nearly constant while strain grows (yield plateau, Lüders bands)
D → E: Strain hardening Dislocation interactions increase strength; stress rises with strain
E: Ultimate tensile strength Maximum engineering stress
E → F: Necking Local reduction in area; engineering stress falls
F: Fracture point Specimen breaks (cup-and-cone fracture)

On a true stress-true strain curve, stress keeps rising until fracture, because the actual (smaller) area is used.

Typical Values for Mild Steel (e.g. IS 2062 E250)

  • Yield strength: about 250 MPa

  • UTS: about 410 MPa

  • E: about 200 GPa

  • Elongation at fracture: about 20–25% or more

Worked Example: Tensile Test Results

Answer: yield ≈ 255 MPa, UTS ≈ 433 MPa, elongation 24% and reduction in area 64%. A specimen of 10 mm diameter and 50 mm gauge length yields at 20 kN, reaches a maximum load of 34 kN, and after fracture has a gauge length of 62 mm and a neck diameter of 6 mm.

  1. A₀ = π/4 × 10² ≈ 78.54 mm²

  2. Yield strength = 20,000 / 78.54 ≈ 254.6 MPa

  3. UTS = 34,000 / 78.54 ≈ 432.9 MPa

  4. % elongation = (62 − 50) / 50 × 100 = 24%

  5. Final area = π/4 × 6² ≈ 28.27 mm² → reduction in area = (78.54 − 28.27) / 78.54 × 100 ≈ 64%

Comparison With Other Materials

  • High-strength steels and aluminium: no distinct yield point, so a 0.2% proof stress (offset method) is used.

  • Cast iron and glass: brittle, nearly linear to fracture with very little plastic strain.

Use in Design

Designers usually limit working stress to yield strength divided by a factor of safety, because permanent deformation is usually unacceptable; UTS and elongation indicate reserve strength and ductility (important for earthquake-resistant structures and formability).

42

What is the difference between yield strength and ultimate tensile strength?

Yield strength is the stress at which a material begins to deform plastically (permanently). Below it, the material returns to its original shape when unloaded. Ultimate tensile strength (UTS) is the maximum stress the material can withstand in tension before necking begins and it moves towards fracture. Yield strength is usually the basis for design, since permanent deformation normally counts as failure, while UTS shows the material’s maximum load capacity.

Read full answer

Applies toMechanical engineering (strength of materials and machine design)

Comparison

Aspect Yield strength (σ_y) Ultimate tensile strength (σ_u)
Meaning Onset of permanent deformation Maximum engineering stress
Position on curve End of elastic region Peak of the curve
After this point Plastic deformation begins Necking and then fracture
Used for Design of ductile parts (most machine and structural design) Brittle materials design; material specification; fatigue estimates
Determination Yield point or 0.2% offset (proof stress) Maximum load / original area

Typical Values

Material Yield (MPa) UTS (MPa) Yield/UTS ratio
Mild steel (IS 2062 E250) 250 410 0.61
Fe 500D rebar 500 565 (min) About 0.88
Bolt grade 8.8 640 800 0.8
Aluminium 6061-T6 About 275 About 310 0.89
Grey cast iron No clear yield About 150–350 —

Bolt grade numbers encode both: for 8.8, UTS = 8 × 100 = 800 MPa, and yield = 0.8 × 800 = 640 MPa.

Worked Example

Answer: the bar yields at 25 kN and can carry at most 41 kN. A mild steel bar (σ_y = 250 MPa, σ_u = 410 MPa) has a cross-sectional area of 100 mm².

  • Yield load = 250 × 100 = 25,000 N (25 kN)

  • Maximum load = 410 × 100 = 41,000 N (41 kN)

  • With a factor of safety of 1.5 on yield, the allowable load = 25 / 1.5 ≈ 16.7 kN

Why the Yield-to-UTS Ratio Matters

  • A lower ratio (more gap between yield and UTS) means more warning and energy absorption before failure, which is desirable for structures in earthquake zones. This is why IS 1786 “D” grade rebars (e.g. Fe 500D) specify a minimum UTS/yield ratio (at least 1.10 for Fe 500D) and higher elongation.

  • High-strength materials often have a ratio close to 1, so they give little warning before fracture.

43

What is a factor of safety?

The factor of safety (FOS) is the ratio of the failure (limiting) stress or load to the working (allowable) stress or load: FOS = failure stress / working stress. It provides a margin for uncertainties in loads, material properties, manufacturing defects, analysis assumptions and wear, so that a part does not fail in service. For ductile materials, failure stress is usually the yield strength; for brittle materials, it is the ultimate strength.

Read full answer

Applies toMechanical engineering (machine design)

Formulas

  • Ductile materials: σ_allow = σ_y / FOS

  • Brittle materials: σ_allow = σ_u / FOS

  • Margin of safety = FOS − 1

Typical Values

Application Typical FOS
Aircraft structures (with precise analysis and testing) About 1.5
Structural steel (on yield, via load and material factors) About 1.5–1.7 overall
General machine parts, steady loads (ductile) About 2–3
Shock or impact loads About 3–5 or more
Brittle materials (cast iron) About 4–8
Lifting equipment (wire ropes, hooks) About 5–10 (as per standards)
Pressure vessels Set by codes (ASME, IS 2825)

Factors Influencing FOS Selection

  • Uncertainty in loads (static, variable, shock).

  • Variability in material properties and quality control.

  • Consequences of failure (risk to life, cost).

  • Accuracy of the analysis method and stress concentrations.

  • Environmental conditions (corrosion, temperature) and wear over time.

  • Codes and standards governing the application.

Worked Example

Answer: an 18 mm diameter rod. A tie rod carries a steady tensile load of 30 kN; the material has σ_y = 250 MPa and the required FOS is 2.

  1. σ_allow = 250 / 2 = 125 MPa

  2. Required area A = 30,000 / 125 = 240 mm²

  3. d = √(4 × 240 / π) ≈ √305.6 ≈ 17.48 mm → choose 18 mm

  4. Check actual FOS with 18 mm: A = 254.5 mm², σ = 117.9 MPa → FOS = 250 / 117.9 ≈ 2.12 ✓

Limit State Design

Modern codes (e.g. IS 800 for steel, IS 456 for concrete) use partial safety factors: loads are multiplied by load factors (e.g. 1.5) and material strengths are divided by material factors (e.g. γ_m0 = 1.10 for steel yield, γ_m = 1.5 for concrete). The overall effect is similar to a factor of safety but is applied more rationally.

Too High vs Too Low

  • Too low: risk of failure.

  • Too high: heavy, costly, inefficient designs (critical in aircraft and vehicles).

44

What is Poisson's ratio?

Poisson’s ratio (ν or µ) is the ratio of lateral (transverse) strain to longitudinal (axial) strain when a material is loaded in one direction within its elastic range: ν = −ε_lateral / ε_longitudinal. When a bar is stretched, it becomes longer and thinner; Poisson’s ratio describes how much thinner. For most metals it is about 0.25–0.35 (steel ≈ 0.3).

Read full answer

Applies toMechanical engineering (strength of materials)

Typical Values

Material Poisson’s ratio
Steel About 0.27–0.30
Aluminium About 0.33
Copper About 0.34
Cast iron About 0.21–0.26
Concrete About 0.15–0.20
Rubber About 0.49–0.5 (nearly incompressible)
Cork About 0 (useful for bottle stoppers)
Auxetic materials Negative

Theoretical range for isotropic materials: −1 < ν ≤ 0.5.

Relations With Other Elastic Constants

  • E = 2G(1 + ν)

  • E = 3K(1 − 2ν)

  • Volumetric strain of a bar under axial load: ε_v = ε(1 − 2ν)

Worked Example

Answer: diameter reduces by about 0.0048 mm and the volume increases by about 100 mm³. A steel rod (E = 200 GPa, ν = 0.3) 20 mm in diameter and 1 m long carries 50 kN in tension.

  1. A ≈ 314.16 mm² → σ ≈ 159.2 MPa

  2. Longitudinal strain ε = 159.2 / 200,000 ≈ 7.96 × 10⁻⁴ → elongation ≈ 0.796 mm

  3. Lateral strain = 0.3 × 7.96 × 10⁻⁴ ≈ 2.39 × 10⁻⁴ → diameter decrease ≈ 20 × 2.39 × 10⁻⁴ ≈ 0.0048 mm

  4. Volumetric strain = 7.96 × 10⁻⁴ × (1 − 0.6) ≈ 3.18 × 10⁻⁴

  5. Original volume = 314.16 × 1,000 ≈ 314,160 mm³ → volume increase ≈ 100 mm³

Why It Matters

  • 3D stress analysis: strains in one direction depend on stresses in the other directions (generalised Hooke’s law: ε_x = [σ_x − ν(σ_y + σ_z)] / E).

  • Press fits and thick cylinders: lateral contraction or expansion affects interference and stresses.

  • Strain gauge measurements: correcting readings for lateral effects.

  • Rubber seals and mounts: near-incompressibility (ν ≈ 0.5) means rubber must have room to bulge when compressed.

45

What is the difference between ductile and brittle materials?

A ductile material can undergo large plastic deformation before fracture, so it stretches, bends and gives visible warning (necking) before breaking; mild steel, copper and aluminium are examples. A brittle material fractures with little or no plastic deformation, suddenly and without warning; cast iron, glass, concrete and ceramics are examples. A common dividing line is about 5% elongation at fracture in a tensile test.

Read full answer

Applies toMechanical engineering (materials and strength of materials)

Comparison

Aspect Ductile Brittle
Elongation at fracture High (often above 5%; mild steel about 20–25%) Low (below 5%, often under 1%)
Stress-strain curve Clear plastic region, necking Nearly linear to fracture
Warning before failure Yes (deformation) No (sudden)
Energy absorbed (toughness) High Low
Fracture surface (tension) Cup-and-cone, fibrous, dull Flat, granular, shiny, perpendicular to load
Strength in compression vs tension Similar Much stronger in compression
Failure theory used Maximum shear stress (Tresca) or von Mises Maximum principal stress (Rankine), Mohr-Coulomb
Design basis Yield strength Ultimate strength (with higher FOS)
Examples Mild steel, copper, aluminium, gold Grey cast iron, glass, concrete, ceramics, chalk

Worked Example: Allowable Stresses

Answer: mild steel allows about 125 MPa, while grey cast iron allows only 50 MPa in tension. Mild steel has σ_y = 250 MPa (FOS 2 on yield); grey cast iron has σ_u = 200 MPa in tension (FOS 4 on ultimate).

  • Mild steel: 250 / 2 = 125 MPa

  • Cast iron: 200 / 4 = 50 MPa

Cast iron is still widely used for machine beds and engine blocks because it is cheap, easily cast, damps vibration well and is strong in compression.

Factors That Change Behaviour

  • Temperature: some steels become brittle at low temperature (ductile-to-brittle transition, e.g. the Titanic and Liberty ship failures).

  • Strain rate: high-speed loading can make materials behave more brittlely.

  • Notches and stress concentrations: promote brittle fracture.

  • Heat treatment: hardening increases brittleness; tempering restores some ductility.

  • Hydrogen embrittlement: high-strength steels can become brittle due to absorbed hydrogen (e.g. from plating).

Tests

Tensile test (elongation, reduction in area), Charpy and Izod impact tests (energy absorbed), bend tests.

46

What are shear force and bending moment diagrams?

A shear force diagram (SFD) shows how the shear force varies along the length of a beam, and a bending moment diagram (BMD) shows how the bending moment varies. Shear force at a section is the algebraic sum of all vertical forces on one side of it; bending moment is the algebraic sum of the moments of those forces about the section. These diagrams locate the maximum shear and maximum moment, which are needed to design the beam.

Read full answer

Applies toMechanical and civil engineering (strength of materials)

Key Relations

  • dM/dx = V (slope of BMD = shear force)

  • dV/dx = −w (slope of SFD = −load intensity)

  • Maximum bending moment occurs where shear force is zero (or changes sign).

  • Point loads cause jumps in the SFD; UDLs make the SFD linear and the BMD parabolic.

Standard Cases

Beam and load Max shear Max bending moment
Simply supported, central point load W W/2 WL/4 (at centre)
Simply supported, UDL w over span L wL/2 wL²/8 (at centre)
Cantilever, end point load W W WL (at fixed end)
Cantilever, UDL w wL wL²/2 (at fixed end)

Worked Example 1: Central Point Load

Answer: reactions 10 kN each, max shear 10 kN, max moment 20 kN·m at the centre. A simply supported beam with a 4 m span carries 20 kN at mid-span.

  • R_A = R_B = 20 / 2 = 10 kN

  • SFD: +10 kN from A to the load, jumps to −10 kN, stays to B

  • M_max = WL/4 = 20 × 4 / 4 = 20 kN·m

Worked Example 2: Uniformly Distributed Load

Answer: reactions 15 kN each and maximum moment 22.5 kN·m at mid-span. A simply supported beam with a 6 m span carries 5 kN/m along its length.

  • Total load = 5 × 6 = 30 kN → R_A = R_B = 15 kN

  • SF at x from A: V = 15 − 5x → zero at x = 3 m (mid-span)

  • M_max = wL²/8 = 5 × 36 / 8 = 22.5 kN·m

Sign Conventions (Common)

  • Shear force: positive when the left part tends to move up relative to the right.

  • Bending moment: positive for sagging (concave up), negative for hogging (as over supports of continuous beams and in cantilevers).

Why They Matter

  • Size the beam: bending stress σ = M/Z must be below allowable stress.

  • Check shear stress near supports.

  • Find points of contraflexure (M = 0) in overhanging and continuous beams, which guide reinforcement placement in RCC.

47

What is moment of inertia, and why are I-sections used for beams?

The moment of inertia (second moment of area, I) of a cross-section measures how its area is distributed about the bending axis: I = ∫y²·dA. A larger I gives a beam greater resistance to bending (lower bending stress, σ = M·y/I, and lower deflection). An I-section places most of the material in the flanges, far from the neutral axis, where it contributes most to I, and uses a thin web for shear. This gives high bending strength and stiffness with much less material and weight than a solid section.

Read full answer

Applies toMechanical and civil engineering (strength of materials)

Common Formulas (About the Centroidal Axis)

Section I Section modulus Z = I / y_max
Rectangle (b × h, bending about the axis parallel to b) bh³/12 bh²/6
Solid circle (diameter d) πd⁴/64 πd³/32
Hollow circle π(D⁴ − d⁴)/64 π(D⁴ − d⁴)/(32D)

Parallel axis theorem: I = I_G + A·h², used for built-up sections.

Worked Example: Rectangle vs I-Section of Equal Depth

Answer: the I-section gives about 54% of the bending strength of the solid rectangle using only 28% of the material, almost twice as efficient per unit of material. Compare a 100 × 200 mm solid rectangle with an I-section 100 mm wide and 200 mm deep, with 20 mm thick flanges and a 10 mm thick web.

Solid rectangle: - I = 100 × 200³ / 12 ≈ 66.67 × 10⁶ mm⁴; Z = 666,667 mm³; area = 20,000 mm²

I-section: - I = (100 × 200³ − 90 × 160³) / 12 = (800 − 368.64) × 10⁶ / 12 ≈ 35.95 × 10⁶ mm⁴- Z = 35.95 × 10⁶ / 100 ≈ 359,500 mm³- Area = 2 × (100 × 20) + 160 × 10 = 5,600 mm²

Section Z (mm³) Area (mm²) Z per unit area
Solid rectangle 666,667 20,000 33.3
I-section 359,500 5,600 64.2

Why the I-Section Works

  • Bending stress is highest at the top and bottom fibres and zero at the neutral axis.

  • Material near the neutral axis carries little bending stress, so it is mostly removed.

  • Flanges resist bending (compression and tension); the web resists shear and holds the flanges apart.

Limitations

  • Weak about the minor axis and in torsion (open section), so they can suffer lateral-torsional buckling; lateral restraint is needed.

  • Thin webs can buckle locally under high shear; stiffeners may be needed.

Applications

Steel building beams (ISMB, ISJB sections in India), bridge girders, crane gantries, machine frames, and rail sections (which have a similar shape).

48

What is torsion, and what is the torsion equation?

Torsion is the twisting of a shaft or member when a torque (twisting moment) acts about its longitudinal axis, producing shear stresses in the cross-section and an angle of twist along its length. The torsion equation for circular shafts is: T / J = τ / r = G·θ / L, where T is torque, J is the polar moment of inertia, τ is shear stress at radius r, G is the modulus of rigidity, θ is the angle of twist (radians) and L is the length.

Read full answer

Applies toMechanical engineering (strength of materials and machine design)

Polar Moment of Inertia

  • Solid shaft: J = πd⁴/32

  • Hollow shaft: J = π(D⁴ − d⁴)/32

  • Maximum shear stress (solid shaft): τ_max = 16T / (πd³)

Power and Torque

P = 2πNT / 60 (P in W, N in rpm, T in N·m)

Worked Example: Shaft Design

Answer: choose a 55 mm shaft; it twists about 1.27° per metre. A solid steel shaft transmits 50 kW at 300 rpm. The allowable shear stress is 60 MPa and G = 80 GPa.

  1. T = 60P / (2πN) = 60 × 50,000 / (2π × 300) ≈ 1,591.5 N·m

  2. d³ = 16T / (π·τ) = 16 × 1,591,500 / (π × 60) ≈ 135,090 mm³ → d ≈ 51.3 mm → choose 55 mm (standard size, also allowing for a keyway)

  3. J = π × 55⁴ / 32 ≈ 898,400 mm⁴

  4. θ per metre = T·L / (G·J) = 1,591,500 × 1,000 / (80,000 × 898,400) ≈ 0.0221 rad ≈ 1.27°

A common stiffness guideline for line shafts is about 0.25° to 1° per metre (depending on the application), so a larger diameter might be needed if stiffness governs.

Assumptions of the Torsion Equation

  • Material is homogeneous, isotropic and obeys Hooke’s law.

  • Circular cross-sections remain plane and circular; radii remain straight.

  • Shaft is straight with uniform cross-section; torque is applied about the axis.

  • Stresses are within the elastic limit.

Hollow vs Solid Shafts

A hollow shaft is stronger and stiffer per unit weight, because material near the centre carries little shear stress. For the same outer diameter, a hollow shaft with d/D = 0.5 has about 94% of the strength of a solid one at 75% of the weight. Used in vehicle propeller shafts and aircraft.

Applications

Drive shafts, axles, turbine and pump shafts, torsion bars in vehicle suspensions, helical springs (wire under torsion), and bolts during tightening.

49

What is buckling, and what is Euler's formula for columns?

Buckling is a sudden sideways (lateral) instability of a slender member under axial compression, which can occur at a stress far below the material’s compressive strength. Once the load reaches the critical (buckling) load, the column bends and can collapse. Euler’s formula gives this critical load for long, slender, elastic columns: P_cr = π²EI / L_e², where E is Young’s modulus, I is the least moment of inertia of the cross-section, and L_e is the effective length.

Read full answer

Applies toMechanical and civil engineering (strength of materials)

Effective Length (L_e)

End conditions L_e
Both ends pinned (hinged) L
One end fixed, other free 2L
Both ends fixed 0.5L
One end fixed, other pinned About 0.7L

Slenderness Ratio

λ = L_e / k, where k = √(I/A) is the least radius of gyration. Euler’s formula is valid only for long columns (for mild steel, roughly λ > 90–100). Short columns fail by crushing; intermediate columns use Rankine-Gordon or Johnson formulas (or code curves such as IS 800).

Worked Example

Answer: about 62 kN for pinned ends, about 248 kN for fixed ends. A solid steel column 40 mm in diameter and 2 m long has E = 200 GPa.

  1. I = π × 40⁴ / 64 ≈ 125,664 mm⁴; A ≈ 1,257 mm²; k = d/4 = 10 mm

  2. Pinned–pinned (L_e = 2,000 mm): λ = 200 (long column) P_cr = π² × 200,000 × 125,664 / 2,000² ≈ 62,000 N ≈ 62 kN

  3. Fixed–fixed (L_e = 1,000 mm): P_cr = 4 × 62 ≈ 248 kN, λ = 100

  4. Crushing load = 1,257 × 250 MPa ≈ 314 kN, so even fixed-fixed, buckling governs

Factors Affecting Buckling Load

  • Length: P_cr ∝ 1/L_e², so doubling the length cuts the load to a quarter.

  • Cross-section shape: tubes and hollow sections give high I for little material.

  • End fixity: better restraint greatly increases capacity.

  • Material stiffness (E), not strength, governs elastic buckling.

  • Imperfections: initial crookedness and eccentric loads reduce real capacity, so codes use reduction factors.

Examples

Building columns, machine tool columns, connecting rods, piston rods in hydraulic cylinders, struts in trusses, lead screws and jack screws, and thin-walled sheets (local buckling).

50

What is fatigue failure, and what is an S-N curve?

Fatigue failure is the failure of a component under repeated or fluctuating (cyclic) loads, at stress levels well below the material’s ultimate strength and often below its yield strength. A crack starts at a stress concentration (notch, surface flaw, weld toe), grows a little with each cycle, and finally the remaining section breaks suddenly. An S-N curve (Wöhler curve) plots stress amplitude (S) against the number of cycles to failure (N, on a log scale), showing how long a material survives at each stress level.

Read full answer

Applies toMechanical engineering (machine design and materials)

Stages of Fatigue Failure

  1. Crack initiation at a stress raiser or surface defect.

  2. Crack propagation: slow growth each cycle, leaving beach marks and striations on the fracture surface.

  3. Final fracture: sudden, when the remaining section can no longer carry the load (rough fracture zone).

S-N Curve Features

  • Endurance limit (fatigue limit): for steels and titanium, a stress below which failure does not occur even after very many cycles (about 10⁶–10⁷). For steels, it is roughly 0.5 × UTS (for polished specimens, UTS up to about 1,400 MPa).

  • Aluminium and copper alloys have no true endurance limit; a fatigue strength at a stated life (e.g. 5 × 10⁸ cycles) is used.

  • Low-cycle fatigue (below about 10³–10⁴ cycles, with plastic strain) vs high-cycle fatigue (elastic stresses, long life).

Worked Example: Goodman Check

Answer: factor of safety ≈ 1.35. A steel part has UTS 600 MPa. The polished endurance limit is about 300 MPa; surface and size factors of 0.8 and 0.85 reduce it. The part sees a mean stress of 150 MPa and an alternating stress of 100 MPa.

  1. Corrected endurance limit: S_e = 300 × 0.8 × 0.85 = 204 MPa

  2. Modified Goodman: σ_a/S_e + σ_m/S_ut = 1/n → 100/204 + 150/600 = 0.490 + 0.25 = 0.740

  3. n = 1 / 0.740 ≈ 1.35

Factors Reducing Fatigue Strength

Stress concentrations (holes, keyways, sharp fillets), rough surfaces, corrosion, size (larger parts are weaker), tensile mean stresses, welding defects, and high temperature.

Ways to Improve Fatigue Life

  • Generous fillet radii and smooth transitions.

  • Polishing and good surface finish.

  • Shot peening, rolling and nitriding (compressive residual surface stresses).

  • Avoid welds at highly stressed locations; grind weld toes.

  • Corrosion protection.

Examples

Axles, crankshafts, connecting rods, springs, aircraft wings and fuselages, bridges, turbine blades and welded structures.

51

What is creep?

Creep is the slow, continuous, time-dependent plastic deformation of a material under a constant load or stress below its yield strength, especially at high temperatures (typically above about 0.4 times the absolute melting temperature for metals). Over time, creep can cause excessive deformation or creep rupture, so it is critical in turbine blades, boiler tubes, steam pipes, furnace parts and jet engines.

Read full answer

Applies toMechanical engineering (materials and machine design)

Stages of Creep (Creep Curve: Strain vs Time)

Stage Behaviour
Instantaneous strain Elastic (and possibly some plastic) strain when load is applied
Primary (transient) creep Creep rate decreases with time as strain hardening dominates
Secondary (steady-state) creep Nearly constant minimum creep rate; balance of hardening and recovery; longest stage and used for design
Tertiary creep Accelerating rate due to necking, voids and cracks, ending in rupture

Factors Affecting Creep

  • Temperature: the dominant factor; creep rate rises exponentially with temperature.

  • Stress: higher stress gives faster creep (power-law relation in the secondary stage).

  • Material: high melting point, stable microstructure, solid-solution strengthening and precipitates resist creep.

  • Grain size: coarse grains or single crystals resist high-temperature creep (grain boundary sliding is reduced).

Worked Example: Larson-Miller Parameter

Answer: about 500 hours to rupture at 650 °C. A steel ruptures in 10,000 hours at 600 °C under a certain stress. Estimate its life at 650 °C under the same stress using LMP = T(C + log₁₀ t), with C = 20 and T in kelvin.

  1. LMP = 873 × (20 + log₁₀ 10,000) = 873 × 24 = 20,952

  2. At 923 K: log₁₀ t = 20,952 / 923 − 20 ≈ 22.70 − 20 = 2.70

  3. t ≈ 10^2.70 ≈ 500 hours

A 50 °C rise cuts life by a factor of about 20, which shows how sensitive creep is to temperature.

Creep-Resistant Materials

  • Cr-Mo steels (e.g. P91, P22) for boiler tubes and steam pipes.

  • Austenitic stainless steels for higher temperatures.

  • Nickel-based superalloys (e.g. Inconel), often directionally solidified or single-crystal, with thermal barrier coatings, for gas turbine blades.

  • Ceramics and refractory metals for very high temperatures.

Related Phenomena

  • Stress relaxation: under constant strain (e.g. bolts at high temperature), stress decreases with time because of creep, so bolts lose preload.

  • Polymers and concrete also creep at room temperature (sagging plastic shelves, long-term deflection of concrete beams).

52

What are the theories of failure?

Theories of failure predict when a material will fail (yield or fracture) under combined (multiaxial) stresses, using results from a simple tensile test. The main theories are: maximum principal stress (Rankine), maximum shear stress (Tresca/Guest), maximum distortion energy (von Mises/Hencky), maximum principal strain (St. Venant) and maximum strain energy (Haigh). For ductile materials, von Mises and Tresca are used; for brittle materials, the maximum principal stress theory (or Mohr-Coulomb) is used.

Read full answer

Applies toMechanical engineering (machine design and strength of materials)

Summary (Failure Conditions, for σ₁ > σ₂ > σ₃)

Theory Failure when Suitable for
Maximum principal stress (Rankine) σ₁ = σ_y (or σ_u) Brittle materials
Maximum shear stress (Tresca) σ₁ − σ₃ = σ_y Ductile; conservative and simple
Maximum distortion energy (von Mises) √[((σ₁−σ₂)² + (σ₂−σ₃)² + (σ₃−σ₁)²)/2] = σ_y Ductile; most accurate
Maximum principal strain (St. Venant) σ₁ − ν(σ₂ + σ₃) = σ_y Limited use
Maximum strain energy (Haigh) σ₁² + σ₂² + σ₃² − 2ν(σ₁σ₂ + σ₂σ₃ + σ₃σ₁) = σ_y² Limited use

For a shaft with bending stress σ and torsional shear τ: - Tresca: σ_eq = √(σ² + 4τ²) - von Mises: σ_eq = √(σ² + 3τ²)

Worked Example

Answer: FOS = 1.60 by Tresca, 1.73 by von Mises and 1.95 by Rankine. A point in a ductile steel part (σ_y = 250 MPa) has σ_x = 100 MPa, σ_y = 0 and τ_xy = 60 MPa.

  1. Principal stresses: σ₁,₂ = 50 ± √(50² + 60²) = 50 ± 78.1 → σ₁ = 128.1 MPa, σ₂ = −28.1 MPa (σ₃ = 0 for plane stress)

  2. Tresca: max difference = 128.1 − (−28.1) = 156.2 MPa → FOS = 250 / 156.2 ≈ 1.60

  3. von Mises: √(100² + 3 × 60²) = √20,800 ≈ 144.2 MPa → FOS = 250 / 144.2 ≈ 1.73

  4. Rankine: 128.1 MPa → FOS = 250 / 128.1 ≈ 1.95 (unsafe to use for ductile materials, since it overestimates the margin)

Comparison

  • Tresca is about 15% more conservative than von Mises in pure shear (it predicts shear yield at 0.5σ_y vs 0.577σ_y).

  • von Mises matches experiments on ductile metals best and is used in FEA software (von Mises stress plots).

  • Rankine works for brittle materials such as cast iron, which fail by tensile fracture.

Applications

Design of shafts under combined bending and torsion, pressure vessels, crankshafts and any component with multiaxial stress.

53

What is the difference between a cam and a follower?

A cam is a rotating or sliding machine element with a specially shaped profile that drives another element. The follower is the element in contact with the cam that is driven by it, moving in a prescribed way (reciprocating or oscillating). Together, a cam and follower convert rotary motion into a precisely timed linear or oscillating motion, as in an engine’s valve train.

Read full answer

Applies toMechanical engineering (theory of machines)

Types of Cams

Basis Types
Shape Disc (radial/plate) cam, cylindrical cam, wedge cam, conical, spherical
Follower motion Rise-dwell-return-dwell (RDRD), rise-return-rise, dwell-rise-return-dwell
Constraint Spring-loaded (force-closed), positive drive (grooved/form-closed)

Types of Followers

Basis Types
Contact surface Knife-edge, roller, flat-faced (mushroom), spherical-faced
Motion Reciprocating (translating), oscillating
Path Radial (in line with cam centre), offset

Roller followers reduce wear and friction; flat-faced followers suit high-speed engines (tappets); knife-edge followers wear fast and are rarely used.

Follower Motion Programmes

  • Uniform velocity: infinite acceleration at ends (shocks); rarely used alone.

  • Simple harmonic motion (SHM): smooth, finite acceleration but jumps at ends.

  • Uniform acceleration and retardation (parabolic): minimum acceleration for given lift.

  • Cycloidal: zero acceleration at ends; best for high speeds.

Worked Example: SHM Follower

Answer: maximum velocity ≈ 0.94 m/s and maximum acceleration ≈ 59 m/s². A follower rises 30 mm with SHM during 90° of cam rotation; the cam turns at 300 rpm.

  1. ω = 2π × 300 / 60 ≈ 31.42 rad/s; β = 90° = π/2 rad

  2. v_max = π·h·ω / (2β) = π × 30 × 31.42 / π ≈ 942 mm/s ≈ 0.94 m/s

  3. a_max = π²·h·ω² / (2β²) = 9.87 × 30 × 987 / (2 × 2.467) ≈ 59,200 mm/s² ≈ 59 m/s²

The spring must provide enough force to keep the follower in contact during retardation (avoiding “jump”).

Key Terms

Base circle, prime circle, pitch curve, lift (stroke), pressure angle (kept below about 30° for translating followers), dwell, trace point.

Applications

IC engine valve operation (camshaft), automatic lathes, textile machinery, printing presses, sewing machines, fuel injection pumps and packaging machines.

54

What is a gear train? What are spur, helical, bevel and worm gears?

A gear train is a combination of two or more gears that transmits motion and power between shafts, usually changing speed and torque. Its train value (output speed / input speed) depends on the numbers of teeth. Spur gears have straight teeth on parallel shafts; helical gears have angled teeth on parallel (or crossed) shafts for smoother, quieter running; bevel gears connect intersecting shafts (usually at 90°); worm gears connect non-intersecting perpendicular shafts and give very large reduction ratios in one stage.

Read full answer

Applies toMechanical engineering (theory of machines and machine design)

Types of Gear Trains

Type Description Example
Simple Each shaft carries one gear Idler gears to change direction
Compound Two gears on an intermediate shaft Lathe headstocks, gearboxes
Reverted Input and output shafts coaxial Clocks, lathe back gear
Epicyclic (planetary) Gear axes move around a central axis Automatic transmissions, differentials, wind turbine gearboxes

Gear Types Compared

Type Shaft arrangement Features Efficiency (typical) Uses
Spur Parallel Simple, cheap, noisy at high speed, no axial thrust About 98–99% per mesh Clocks, gearboxes, pumps
Helical Parallel (or crossed) Gradual engagement, quiet, higher load; axial thrust About 97–99% Car gearboxes, industrial reducers
Double helical / herringbone Parallel No net axial thrust About 97–99% Turbines, heavy reducers
Bevel (straight/spiral) Intersecting (usually 90°) Changes direction of drive About 95–98% Differentials, hand drills
Worm and worm wheel Non-intersecting, perpendicular High ratio (10:1 to 100:1), can be self-locking About 50–90% Lifts, hoists, conveyors, tuning pegs
Rack and pinion Rotary to linear Converts rotation to translation High Steering, CNC axes

Worked Example: Compound Gear Train

Answer: speed ratio 9:1, output 160 rpm, output torque about 86 N·m. A 20-tooth driver meshes with a 60-tooth gear; a 25-tooth gear on the same shaft meshes with a 75-tooth output gear. Input is 1,440 rpm and 10 N·m, and each mesh is 98% efficient.

  1. Speed ratio = (60/20) × (75/25) = 3 × 3 = 9

  2. Output speed = 1,440 / 9 = 160 rpm

  3. Output torque = 10 × 9 × 0.98² ≈ 10 × 9 × 0.96 ≈ 86.4 N·m

Worm Gear Example

A single-start worm driving a 40-tooth wheel gives a 40:1 reduction in one stage.

Key Gear Terms

Module (m = pitch circle diameter / number of teeth), pressure angle (commonly 20°), pitch circle, addendum, dedendum, backlash. Meshing gears must have the same module and pressure angle.

55

What is the difference between a flywheel and a governor?

A flywheel is a heavy rotating wheel that stores kinetic energy and smooths out speed fluctuations within each cycle of an engine or machine, absorbing energy when supply exceeds demand and releasing it when demand exceeds supply. A governor controls the mean speed of an engine over a longer period by adjusting the fuel or steam supply when the load changes. In short, the flywheel handles cyclic fluctuations; the governor handles load-dependent changes.

Read full answer

Applies toMechanical engineering (theory of machines)

Comparison

Aspect Flywheel Governor
Purpose Limits speed fluctuation within a cycle Maintains mean speed as load varies
Controls Energy storage (no control of fuel) Fuel or working fluid supply
Timescale Within one cycle Over many cycles
Cause addressed Uneven turning moment (e.g. power strokes) or uneven load during a cycle (e.g. punching press) Change in external load
Type of device Passive inertia Control mechanism (mechanical, hydraulic, electronic)
Examples Engines, punching and shearing presses, compressors DG sets, steam turbines, hydro turbines (now electronic governors)

Flywheel Design Formula

ΔE = I·ω²·C_s

  • ΔE = maximum fluctuation of energy (J)

  • I = moment of inertia (kg·m²) = m·k² (k = radius of gyration)

  • ω = mean angular speed (rad/s)

  • C_s = coefficient of fluctuation of speed = (ω_max − ω_min) / ω_mean

Worked Example

Answer: I ≈ 253 kg·m², or about 253 kg at a 1 m radius of gyration. An engine runs at a mean speed of 300 rpm. The maximum fluctuation of energy is 5,000 J, and speed must stay within ±1% (C_s = 0.02).

  1. ω = 2π × 300 / 60 ≈ 31.42 rad/s; ω² ≈ 987

  2. I = ΔE / (ω²·C_s) = 5,000 / (987 × 0.02) ≈ 253 kg·m²

  3. With a radius of gyration of 1 m: m = 253 / 1² ≈ 253 kg

Types of Governors

  • Centrifugal governors: Watt (simple, slow engines), Porter, Proell, Hartnell (spring-loaded, high speed).

  • Inertia governors: respond to rate of change of speed.

  • Modern electronic governors: speed sensors and actuators (in DG sets and turbines), with droop settings for load sharing.

Governor Terms

Sensitiveness, stability, isochronism (constant speed at all positions), hunting (continuous oscillation of speed), effort and power.

56

What is balancing of rotating masses?

Balancing of rotating masses is the process of adding or removing mass so that the centrifugal forces and couples produced by rotating parts cancel out. An unbalanced mass at radius r rotating at angular speed ω produces a force F = m·r·ω² that rotates with the shaft, causing vibration, noise, bearing loads and fatigue. Balancing is essential for fans, rotors, crankshafts, wheels, turbines and pumps.

Read full answer

Applies toMechanical engineering (theory of machines)

Types of Balancing

Type Condition Method
Static balancing Resultant centrifugal force = 0 (Σ m·r = 0) Balance in a single plane; rotor stays at rest in any position
Dynamic balancing Resultant force = 0 and resultant couple = 0 (Σ m·r·l = 0) Balance in two planes; needed for long rotors

A rotor can be statically balanced but dynamically unbalanced (two equal masses at opposite ends on opposite sides produce a couple).

Worked Example

Answer: the unbalanced force is about 494 N; a 33.3 g balancing mass at 150 mm on the opposite side cancels it. A 50 g unbalanced mass sits at a radius of 100 mm on a rotor running at 3,000 rpm.

  1. ω = 2π × 3,000 / 60 ≈ 314.16 rad/s; ω² ≈ 98,696

  2. F = 0.05 × 0.1 × 98,696 ≈ 493.5 N

  3. Balancing mass at 150 mm: m_b = 0.05 × 100 / 150 ≈ 0.0333 kg (33.3 g), placed diametrically opposite

A mere 50 g mass produces a force of about 50 kg weight at this speed, and it doubles if the speed rises by about 41%, since F ∝ ω².

Several Masses in Different Planes

Use the graphical or analytical method: 1. Choose two reference (balancing) planes. 2. Resolve each mass’s m·r and m·r·l (l measured from one reference plane). 3. Draw the couple polygon to find the balance mass in the second plane, then the force polygon for the first plane.

Balancing Machines and Standards

  • Dynamic balancing machines measure unbalance in two planes and show where to correct.

  • ISO 21940-11 (formerly ISO 1940) balance quality grades, e.g. G6.3 for fans and pump impellers, G2.5 for turbines and machine tool spindles, G1 for grinding spindles.

  • Field balancing with portable vibration analysers.

Related: Reciprocating Masses

Engines also have reciprocating masses (pistons), which cause primary and secondary unbalanced forces; these are partly balanced by crank counterweights, cylinder arrangement (e.g. inline-six is inherently balanced) and balancer shafts.

57

What is vibration, and what is resonance?

Vibration is the repeated oscillatory motion of a body or system about an equilibrium position. Every elastic system has one or more natural frequencies, at which it vibrates freely when disturbed. Resonance occurs when the frequency of an external exciting force matches (or is close to) a natural frequency; the amplitude then becomes very large, limited only by damping, which can cause noise, fatigue and failure.

Read full answer

Applies toMechanical engineering (theory of machines and vibration)

Types of Vibration

Type Description
Free System vibrates after an initial disturbance, at its natural frequency
Forced Continuous external excitation (e.g. unbalance, engine firing)
Damped / undamped With or without energy dissipation
Longitudinal, transverse, torsional Direction of motion
Linear / non-linear Depending on system characteristics

Natural Frequency (Single Degree of Freedom)

ω_n = √(k/m) (rad/s); f_n = (1/2π)·√(k/m) (Hz)

For static deflection δ: f_n ≈ 0.4985 / √δ (δ in m), i.e. about 15.76/√δ with δ in mm.

Worked Example: Avoiding Resonance

Answer: the machine resonates at about 604 rpm; mounts with stiffness about 65.7 kN/m give 80% isolation. A machine of mass 100 kg is mounted on springs with total stiffness 400 kN/m and runs at 600 rpm (10 Hz).

  1. ω_n = √(400,000 / 100) ≈ 63.25 rad/s → f_n ≈ 10.07 Hz ≈ 604 rpm (almost exactly the running speed, so resonance)

  2. For about 80% isolation (undamped transmissibility T = 1/(r² − 1) = 0.2), the frequency ratio r = f/f_n must be about 2.45

  3. Required f_n = 10 / 2.45 ≈ 4.08 Hz → k = m(2πf_n)² = 100 × 25.64² ≈ 65.7 kN/m

Isolation begins only when r > √2 (≈ 1.41); below that, mounts amplify vibration.

Effects of Resonance

  • Large amplitudes, noise, discomfort.

  • Fatigue cracks in shafts, blades, brackets and pipes.

  • Bearing damage and loosening of fasteners.

  • Famous failures: Tacoma Narrows Bridge (aeroelastic flutter, a related instability), turbine blade failures.

Ways to Control Vibration

  • Change natural frequency (stiffness or mass) to move away from operating speeds.

  • Balance rotating parts and align shafts.

  • Add damping (rubber mounts, viscous dampers).

  • Isolation mounts (springs, rubber pads).

  • Tuned mass dampers (tall buildings, crankshaft dampers).

  • Run quickly through critical speeds during start-up and shutdown.

Measurement

Accelerometers, velocity probes, FFT analysers; ISO 10816/20816 vibration severity limits for machines.

58

What are the types of bearings, and how do you select one?

Bearings support rotating or sliding parts, carry loads and reduce friction. The two main groups are rolling-element (anti-friction) bearings, such as ball, roller, tapered roller, needle and thrust bearings, and sliding (plain/journal) bearings, such as bushes and hydrodynamic or hydrostatic bearings. Selection depends on load type and size, speed, required life, space, alignment, lubrication, environment and cost.

Read full answer

Applies toMechanical engineering (machine design)

Rolling-Element Bearings

Type Load capacity Speed Features / uses
Deep groove ball Radial + moderate axial High Most common; motors, fans, pumps
Angular contact ball Radial + high axial (one direction) High Machine tool spindles, pumps (in pairs)
Self-aligning ball Radial, tolerates misalignment Medium Long shafts, agricultural machinery
Cylindrical roller High radial High Gearboxes, motors (non-locating side)
Tapered roller High radial + axial Medium Wheel hubs, gearboxes, differentials
Spherical roller Very high radial, misalignment Medium Heavy machinery, crushers, conveyors
Needle roller High radial in small space Medium Gearboxes, rocker arms, two-wheelers
Thrust ball / roller Axial Low–medium Vertical shafts, turntables

Plain (Sliding) Bearings

  • Hydrodynamic journal bearings: oil film generated by rotation; used in turbines, large engines (crankshaft bearings).

  • Hydrostatic bearings: externally pressurised oil; precision machine tools.

  • Bushes: bronze, PTFE, nylon; low-speed or oscillating applications.

Life Calculation (Rolling Bearings)

L₁₀ = (C / P)^p million revolutions (p = 3 for ball bearings, 10/3 for roller bearings)

L₁₀h = L₁₀ × 10⁶ / (60 × N) hours

Worked Example

Answer: about 11,100 hours. A deep groove ball bearing has dynamic load rating C = 30 kN and equivalent load P = 3 kN at 1,500 rpm.

  1. L₁₀ = (30 / 3)³ = 1,000 million revolutions

  2. L₁₀h = 1,000 × 10⁶ / (60 × 1,500) ≈ 11,111 hours

So 90% of identical bearings will exceed about 11,100 hours under these conditions. Halving the load would increase life eight times.

Selection Steps

  1. Determine radial and axial loads, speed and required life (e.g. 20,000–40,000 h for industrial machines).

  2. Consider space, misalignment and stiffness needs.

  3. Choose type and size from catalogues (SKF, FAG, NBC, Timken) by calculating required C.

  4. Select fits, clearance class, sealing and lubrication (grease or oil).

59

What is the difference between a clutch and a brake?

A clutch connects and disconnects a driving shaft from a driven shaft, so power can be transmitted or interrupted without stopping the engine; it makes both shafts rotate together when engaged. A brake absorbs the kinetic energy of a moving or rotating part to slow it down or stop it, usually converting that energy into heat by friction. Both often use friction surfaces, but a clutch transmits power while a brake dissipates it.

Read full answer

Applies toMechanical engineering (machine design and automobile engineering)

Comparison

Aspect Clutch Brake
Function Engages or disengages power transmission Slows or stops motion
Energy Transmits energy (some slip loss) Dissipates kinetic energy as heat
Connection Between two rotating shafts Between a moving part and a fixed frame
Types Single-plate, multi-plate, cone, centrifugal, dog clutch, fluid coupling, electromagnetic Drum (shoe), disc, band, block, electromagnetic, regenerative, hydraulic retarders
Examples Car clutch, motorcycle wet multi-plate clutch, centrifugal clutch in scooters Car disc brakes, drum brakes, crane brakes, train brakes

Worked Example 1: Single-Plate Clutch Torque

Answer: about 300 N·m, enough for about 62.8 kW at 2,000 rpm. A single-plate clutch with two friction surfaces has inner radius 100 mm and outer radius 150 mm, µ = 0.3 and axial spring force 4 kN (uniform wear theory).

  1. Mean radius = (0.15 + 0.10) / 2 = 0.125 m

  2. T = n·µ·W·R_mean = 2 × 0.3 × 4,000 × 0.125 = 300 N·m

  3. Power at 2,000 rpm = 2π × 2,000 × 300 / 60 ≈ 62.8 kW

Worked Example 2: Braking a Car

Answer: the brakes absorb 240 kJ, stopping the car in about 33 m and 3.3 s. A 1,200 kg car travels at 20 m/s (72 km/h) and decelerates at 6 m/s².

  1. Kinetic energy = ½ × 1,200 × 20² = 240,000 J

  2. Stopping distance = v² / (2a) = 400 / 12 ≈ 33.3 m

  3. Stopping time = 20 / 6 ≈ 3.33 s; average braking power ≈ 240 / 3.33 ≈ 72 kW, all turned into heat in the brakes

Design Considerations

  • Friction material: high and stable µ, wear resistance, heat resistance (sintered metals, organic, ceramic).

  • Heat dissipation: ventilated discs, cooling fins, oil cooling.

  • Fade: loss of friction at high temperature.

  • Brakes in EVs and hybrids increasingly use regenerative braking, recovering energy into the battery.

60

What are the types of joints: bolted, riveted, welded, keys and couplings?

Mechanical joints connect parts so they can transmit loads or motion. Bolted (threaded) joints are temporary and can be dismantled. Riveted joints are permanent fastenings by deformed rivets. Welded joints are permanent joints formed by fusing the parts. Keys lock a gear, pulley or coupling to a shaft so torque is transmitted. Couplings connect two shafts end to end to transmit power, rigidly or flexibly.

Read full answer

Applies toMechanical engineering (machine design)

Comparison of Fastening Methods

Joint Permanent? Features Typical uses
Bolted / screwed No Easy assembly and dismantling; preload; can loosen under vibration Machine assemblies, flanges, structural connections
Riveted Yes Good for dissimilar metals and fatigue; holes weaken plates; labour-intensive Aircraft skins, older bridges, boilers (historically)
Welded Yes Strong, leak-tight, no holes, lighter; residual stresses and distortion; inspection needed Structures, pressure vessels, pipelines, vehicle frames
Adhesive Yes Distributes stress, joins dissimilar materials Aerospace, automotive panels

Keys

Type Features
Sunk (rectangular or square) key Most common; IS 2048 sizes based on shaft diameter
Feather key Allows axial sliding of hub
Woodruff key Semicircular; self-aligning; tapered shafts
Gib-head key Tapered, easy removal
Splines Multiple integral keys; high torque, sliding (gearboxes, propeller shafts)

Couplings

  • Rigid: sleeve (muff), clamp, flange coupling; need accurate alignment.

  • Flexible: bush-pin, jaw (spider), gear, tyre, disc couplings; accommodate misalignment and damp shocks.

  • Special: universal (Hooke’s) joint for angular misalignment, Oldham coupling for parallel offset, fluid couplings for soft starting.

Worked Example: Key Length

Answer: a 75 mm long key. A 50 mm shaft transmits 1,000 N·m through a 14 × 9 mm key. Allowable shear stress is 60 MPa and allowable crushing stress is 120 MPa.

  1. Tangential force at shaft surface F = 2T / d = 2 × 1,000,000 / 50 = 40,000 N

  2. Shear: L = F / (b × τ) = 40,000 / (14 × 60) ≈ 47.6 mm

  3. Crushing (half the key height bears on the hub): L = F / ((h/2) × σ_c) = 40,000 / (4.5 × 120) ≈ 74.1 mm

  4. Crushing governs → use a 75 mm key (hub length should be at least this)

Welded Joint Example

A 6 mm fillet weld with allowable shear stress 110 MPa carries 0.707 × 6 × 110 ≈ 467 N per mm of length, so a 30 kN load needs about 64 mm of weld (plus allowance for starts and stops).

61

What is the difference between steel and cast iron?

Steel and cast iron are both iron-carbon alloys, but they differ mainly in carbon content. Steel contains up to about 2.1% carbon (most engineering steels under about 1%), which makes it strong, ductile, tough and weldable. Cast iron contains about 2.1–4% carbon (often with 1–3% silicon), which makes it brittle in tension but easy to cast, strong in compression, good at damping vibration and cheap to produce.

Read full answer

Applies toMechanical engineering (engineering materials)

Comparison

Property Steel Cast iron
Carbon content Up to about 2.1% (mild steel about 0.05–0.25%) About 2.1–4%
Ductility High (elongation about 20–25% for mild steel) Low (grey CI below 1%)
Tensile strength High (mild steel about 410 MPa) Low to moderate (grey CI about 150–350 MPa)
Compressive strength Similar to tensile Much higher than tensile (about 3–4 times)
Impact resistance Good Poor (grey CI)
Castability Fair (high melting point about 1,450–1,520 °C) Excellent (lower melting about 1,150–1,250 °C, good fluidity)
Machinability Good Excellent (graphite acts as chip breaker and lubricant)
Weldability Good (low-carbon steels) Poor (needs preheating, special rods)
Vibration damping Low High (graphite flakes absorb vibration)
Forgeability Can be forged and rolled Cannot be forged
Cost Higher Lower

Types of Cast Iron

  • Grey CI: graphite flakes; good damping and machinability (machine beds, engine blocks).

  • White CI: carbon as cementite; very hard, brittle, wear-resistant (liners, rolls).

  • Ductile (SG/nodular) CI: spherical graphite via magnesium; much tougher (crankshafts, pipes, gears).

  • Malleable CI: heat-treated white iron; some ductility (fittings, small parts).

Worked Example: Cross-Section Needed for a Tensile Load

Answer: steel needs 400 mm² and grey cast iron about 769 mm² (almost twice). A member carries 50 kN in tension. Mild steel: σ_y = 250 MPa with FOS 2. Grey cast iron (FG 260): σ_u = 260 MPa with FOS 4.

  • Steel: allowable = 125 MPa → A = 50,000 / 125 = 400 mm²

  • Cast iron: allowable = 65 MPa → A = 50,000 / 65 ≈ 769 mm²

In compression, cast iron’s much higher strength reduces this gap considerably.

Typical Uses

  • Steel: structures, shafts, gears, fasteners, vehicle bodies, tools, pressure vessels.

  • Cast iron: machine tool beds, engine blocks, pump casings, manhole covers, pipes (DI), brake drums, flywheels.

62

What is the iron-carbon phase diagram?

The iron-carbon (Fe-Fe₃C) phase diagram shows which phases and microstructures exist in iron-carbon alloys at different carbon contents (0–6.67%) and temperatures, under slow (near-equilibrium) cooling. It is the basis for understanding steels and cast irons and for designing heat treatments. Key points are the eutectoid at 0.76% C and 727 °C (austenite → pearlite) and the eutectic at 4.3% C and 1,147 °C (liquid → ledeburite).

Read full answer

Applies toMechanical engineering (metallurgy)

Main Phases

Phase Structure Carbon solubility Properties
Ferrite (α) BCC Max about 0.022% at 727 °C Soft, ductile, magnetic
Austenite (γ) FCC Max about 2.14% at 1,147 °C Soft, ductile, non-magnetic; stable at high temperature
Delta ferrite (δ) BCC Max about 0.09% Exists only at very high temperature
Cementite (Fe₃C) Orthorhombic compound 6.67% Very hard and brittle
Pearlite Lamellar ferrite + cementite Eutectoid mixture at 0.76% C Strong, moderately ductile
Ledeburite Austenite + cementite (eutectic) 4.3% C Hard, brittle (in cast irons)

Invariant Reactions

Reaction Composition Temperature Change
Peritectic About 0.16% C About 1,493 °C δ + liquid → γ
Eutectic 4.3% C 1,147 °C Liquid → γ + Fe₃C (ledeburite)
Eutectoid 0.76% C 727 °C γ → α + Fe₃C (pearlite)

Important Lines

  • A₁: 727 °C (eutectoid temperature).

  • A₃: upper critical line for hypoeutectoid steels (ferrite starts forming on cooling).

  • A_cm: upper critical line for hypereutectoid steels (cementite starts forming).

  • Steels: below about 2.1% C (hypoeutectoid below 0.76%, hypereutectoid above). Cast irons: above about 2.1% C.

Worked Example: Lever Rule

Answer: a 0.4% C steel just below 727 °C has about 51% pearlite and 49% proeutectoid ferrite, with about 5.7% cementite overall.

  1. Pearlite fraction = (0.4 − 0.022) / (0.76 − 0.022) = 0.378 / 0.738 ≈ 51.2%

  2. Proeutectoid ferrite = 100 − 51.2 ≈ 48.8%

  3. Total cementite = (0.4 − 0.022) / (6.67 − 0.022) ≈ 0.378 / 6.648 ≈ 5.7%

Uses

  • Choosing heat treatment temperatures (e.g. hardening about 30–50 °C above A₃ for hypoeutectoid steels).

  • Predicting microstructure and properties of steels with different carbon contents.

  • Understanding welding heat-affected zones.

Note: the diagram applies to slow cooling; fast cooling forms non-equilibrium phases such as martensite and bainite, described by TTT and CCT diagrams.

63

What are annealing, normalising, hardening and tempering in heat treatment?

Heat treatment is the controlled heating and cooling of metals, mainly steels, to change their microstructure and properties (hardness, strength, ductility, toughness, machinability, internal stresses) without changing their shape. The four basic treatments are annealing (soften), normalising (refine grains), hardening (make hard by quenching) and tempering (reduce brittleness after hardening).

Read full answer

Applies toMechanical engineering (metallurgy and manufacturing)

Comparison (for a Medium-Carbon Steel, About 0.4% C)

Process Heating Cooling Result Purpose
Full annealing About 30–50 °C above A₃ (about 830–860 °C) Very slowly in furnace Coarse pearlite + ferrite; soft, ductile Improve machinability, relieve stresses, prepare for cold working
Normalising About 40–60 °C above A₃ (about 860–880 °C) In still air Fine pearlite + ferrite; slightly harder and stronger than annealed Refine grain after forging or casting, uniform structure
Hardening About 30–50 °C above A₃ (about 840–860 °C) Rapid quench (water, oil, polymer) Martensite; very hard and brittle Wear resistance, high strength
Tempering Reheat below A₁ (about 150–650 °C) Usually air Tempered martensite; tougher, less hard Reduce brittleness and stresses after hardening

Other treatments: stress relieving (about 550–650 °C), spheroidise annealing (for high-carbon steels), austempering and martempering.

Worked Example: Hardening and Tempering a C45 Shaft

Answer: about 2 hours soaking at about 850 °C, oil or water quench, then temper about 2 hours at 550 °C for roughly 25–30 HRC. A 50 mm diameter C45 (EN8-type) shaft needs good toughness with moderate hardness.

  1. Soaking time (common rule of thumb: about 1 hour per 25 mm of section): 50 / 25 = 2 hours at about 850 °C

  2. Quench in water or oil (C45 in thick sections hardens mainly at the surface because of limited hardenability); surface hardness about 50–55 HRC

  3. Temper at about 550 °C for about 2 hours → hardness about 25–30 HRC, with much better toughness

(Actual temperatures and times should follow the steel supplier’s data sheet.)

Effect of Tempering Temperature

Tempering range Typical result
About 150–250 °C High hardness retained, stress relieved (tools, gauges)
About 350–450 °C Springs (good elasticity)
About 500–650 °C Tough, strong (shafts, gears, bolts): “quenched and tempered”

Practical Points

  • Quench cracking risk: avoid sharp corners, choose suitable quenchant.

  • Temper immediately after hardening.

  • Decarburisation and scaling: use protective atmospheres or allowance for grinding.

64

What is case hardening?

Case hardening (surface hardening) produces a hard, wear-resistant surface layer (case) on a component while keeping a tough, ductile core. It suits parts like gears, camshafts and pins that must resist surface wear and contact fatigue but also absorb shocks without breaking. Methods either change the surface chemistry (carburising, nitriding, carbonitriding) or only heat-treat the surface (induction and flame hardening).

Read full answer

Applies toMechanical engineering (metallurgy and manufacturing)

Methods

Method How Temperature Typical case depth Steels
Carburising (pack, gas, liquid) Carbon diffuses into surface, then quench and temper About 900–950 °C About 0.5–2 mm Low-carbon steels (e.g. 20MnCr5, EN353, 16MnCr5)
Nitriding Nitrogen diffuses forming hard nitrides; no quench About 500–550 °C About 0.1–0.6 mm Nitriding steels with Al, Cr, Mo (EN41B)
Carbonitriding Carbon + nitrogen, then quench About 800–870 °C About 0.1–0.75 mm Low-carbon steels, small parts
Induction hardening Surface heated by induction coil, then quenched Above A₃ at surface About 1–6 mm Medium-carbon steels (C45, 40Cr)
Flame hardening Surface heated by oxy-fuel flame, then quenched Above A₃ at surface About 1.5–6 mm Medium-carbon steels, large parts
Laser / electron beam Very localised heating — Shallow Precision parts

Worked Example: Carburising Time

Answer: about 2.5 hours for a 1 mm case and about 5.6 hours for 1.5 mm. Using the empirical Harris relation for gas carburising at about 925 °C: case depth d ≈ 0.635 × √t (d in mm, t in hours).

  1. For d = 1.0 mm: t = (1.0 / 0.635)² ≈ 2.5 hours

  2. For d = 1.5 mm: t = (1.5 / 0.635)² ≈ 5.6 hours

Doubling the case depth needs four times the time, because diffusion depth grows with the square root of time.

Advantages

  • Hard surface (about 58–62 HRC after carburising and quenching) resists wear and pitting.

  • Tough core resists impact and bending fatigue.

  • Compressive residual stresses at the surface improve fatigue life.

  • Nitriding gives minimal distortion (no quenching).

Applications

Gears, camshafts, crankshaft journals, piston pins, bearing races, spline shafts, tappets and machine tool slides.

Quality Checks

Surface and core hardness, effective case depth (e.g. depth to 550 HV), microstructure, distortion measurement.

65

What is the difference between hardness, toughness and strength?

Strength is a material’s ability to resist deformation and failure under load (yield strength, tensile strength, compressive strength). Hardness is its resistance to localised plastic deformation, such as indentation, scratching or wear. Toughness is its ability to absorb energy and deform plastically before fracturing, combining strength and ductility. A material can be hard but not tough (glass, hardened tool steel) or tough but not very hard (mild steel, copper).

Read full answer

Applies toMechanical engineering (engineering materials)

Comparison

Property Definition Measured by Units
Strength Resistance to yielding or breaking under load Tensile, compression, shear tests MPa
Hardness Resistance to indentation, scratching, wear Brinell, Rockwell, Vickers, Knoop, Shore, Mohs HB, HRC, HV, etc.
Toughness Energy absorbed before fracture Charpy or Izod impact test; fracture toughness (K_IC); area under stress-strain curve J, J/m³, MPa√m

Relationships

  • Hardness and tensile strength are roughly related for steels: UTS (MPa) ≈ 3.45 × HB (approximate).

  • Increasing hardness (e.g. by quenching) usually reduces toughness; tempering trades some hardness back for toughness.

  • Toughness needs both strength and ductility: a material that is strong but brittle has low toughness.

Worked Example: Brinell Hardness

Answer: about 229 HBW, suggesting a tensile strength of about 790 MPa. A Brinell test uses a 10 mm ball and a 3,000 kgf load, leaving an indentation 4.0 mm in diameter.

  1. BHN = 2P / (πD(D − √(D² − d²)))

  2. √(100 − 16) ≈ 9.165 → D − 9.165 = 0.835

  3. πD × 0.835 ≈ 31.416 × 0.835 ≈ 26.23

  4. BHN = 6,000 / 26.23 ≈ 229 HBW

  5. Approximate UTS ≈ 3.45 × 229 ≈ 790 MPa

Typical Examples

Material Strength Hardness Toughness
Mild steel Moderate Low (about 120–140 HB) High
Hardened tool steel High Very high (about 60–65 HRC) Low
Quenched and tempered alloy steel High Medium–high High
Grey cast iron Low in tension Medium Low
Glass Moderate (compression) High Very low
Rubber Low Very low High (energy absorption)

Why It Matters in Design

  • Gears and bearings need hard surfaces (wear) and tough cores (shock): case hardening.

  • Structures in cold climates need toughness at low temperature (Charpy requirements, e.g. 27 J at a specified temperature for structural steel grades).

  • Cutting tools need hardness at high temperature (hot hardness).

66

What are the main casting processes and common casting defects?

Casting is a manufacturing process in which molten metal is poured into a mould shaped like the required part and allowed to solidify. Common processes include sand casting, die casting (gravity and pressure), investment casting, centrifugal casting, shell moulding and continuous casting. Typical defects include shrinkage cavities, gas porosity, blowholes, cold shuts, misruns, hot tears, inclusions and dimensional errors.

Read full answer

Applies toMechanical engineering (manufacturing processes)

Casting Processes

Process Mould Features Typical products
Sand casting Expendable sand mould Any size, low tooling cost, rough finish Engine blocks, pump casings, machine beds
Shell moulding Resin-bonded sand shell Better finish and accuracy Cylinder heads, small castings
Investment (lost wax) Ceramic shell around wax pattern Complex shapes, excellent finish Turbine blades, jewellery, medical implants
Gravity die casting Permanent metal mould Good finish, medium volumes Aluminium pistons, wheels
High-pressure die casting Steel die, metal injected under pressure High volume, thin walls, excellent finish Aluminium/zinc housings, gearbox cases
Centrifugal casting Rotating mould Dense, defect-free walls Pipes, cylinder liners, bushes
Continuous casting Water-cooled mould, continuous withdrawal Billets, slabs, blooms Steel mills

Common Defects

Defect Cause Remedy
Shrinkage cavity Insufficient feeding during solidification Proper risers, directional solidification, chills
Gas porosity / blowholes Dissolved gases, moist sand, low permeability Degassing, dry moulds, vents, better permeability
Cold shut / misrun Low pouring temperature, slow pouring, thin sections Higher pouring temperature, better gating
Hot tear Restrained contraction at high temperature Collapsible cores, uniform sections, fillets
Inclusions (sand, slag) Eroded sand, poor skimming Filters, clean ladles, strong moulds
Mould shift / mismatch Misaligned cope and drag Accurate pins and flasks
Swell, fins, scabs Weak moulds, poor ramming Proper ramming, mould strength

Worked Example 1: Pattern Shrinkage Allowance

Answer: 505 mm for grey cast iron and 510 mm for steel. A casting must measure 500 mm. Typical shrinkage allowances are about 1% for grey cast iron and 2% for steel.

  • Grey CI: 500 × 1.01 = 505 mm

  • Steel: 500 × 1.02 = 510 mm

Worked Example 2: Solidification Time (Chvorinov’s Rule)

Answer: about 9.3 minutes. A 100 mm cube is cast with mould constant B = 2 s/mm².

  1. Modulus V/A = (100³) / (6 × 100²) = 100 / 6 ≈ 16.67 mm

  2. t = B × (V/A)² = 2 × 16.67² ≈ 556 s ≈ 9.3 minutes

A riser must solidify after the casting, so it is designed with a larger modulus (often about 1.2 times the casting’s).

67

What is the difference between arc welding, gas welding and resistance welding?

Arc welding uses the heat of an electric arc between an electrode and the workpiece (about 5,000–6,000 °C or higher) to melt and fuse metals. Gas welding uses the flame from burning a fuel gas with oxygen (oxy-acetylene, about 3,100–3,200 °C) to melt the joint. Resistance welding passes a high current through the contact area of parts pressed together, so electrical resistance generates heat (I²Rt) and forms the weld under pressure, usually without filler metal.

Read full answer

Applies toMechanical engineering (manufacturing, welding)

Comparison

Aspect Arc welding Gas welding Resistance welding
Heat source Electric arc Oxy-fuel flame Joule heating at contact (I²Rt)
Temperature Very high (arc) About 3,100–3,200 °C (oxy-acetylene) Localised at interface
Filler metal Usually (electrode or wire) Optional filler rod None
Pressure No No Yes
Speed Fast Slow Very fast (fractions of a second per spot)
Heat-affected zone Moderate Wide (slow heating) Small
Thickness range Thin to very thick Thin sheets, repair Thin sheets (about 0.5–3 mm typical)
Automation Easy (MIG/TIG/SAW robots) Manual Highly automated (car body lines)
Equipment Power source, electrodes Cylinders, regulators, torch Transformer, electrodes, controller
Examples SMAW (stick), MIG/MAG (GMAW), TIG (GTAW), SAW, FCAW Oxy-acetylene welding, brazing, cutting Spot, seam, projection, flash butt, upset welding

Worked Example 1: Arc Welding Heat Input

Answer: about 1.04 kJ/mm. Stick (SMAW) welding at 24 V and 180 A with a travel speed of 200 mm/min and arc efficiency 0.8.

Heat input = (V × I × 60) / (1,000 × travel speed) × η = (24 × 180 × 60) / (1,000 × 200) × 0.8 ≈ 1.296 × 0.8 ≈ 1.04 kJ/mm

Heat input controls cooling rate, distortion and HAZ properties; welding procedures (WPS) specify limits.

Worked Example 2: Spot Weld Heat

Answer: 2,000 J per spot. Current 10,000 A, contact resistance 100 µΩ, weld time 0.2 s.

H = I²Rt = 10,000² × 100 × 10⁻⁶ × 0.2 = 2,000 J

Typical Applications

  • Arc: structural steel, pipelines, pressure vessels, ship building, fabrication shops.

  • Gas: maintenance and repair, thin sheet metal, plumbing, cutting steel (oxy-fuel cutting).

  • Resistance: automobile bodies (thousands of spot welds per car), appliance cabinets, wire mesh, rail flash butt welding.

Safety

Arc radiation (UV, IR) needs shaded helmets; fumes need ventilation; gas cylinders need flashback arrestors and safe storage; resistance welding needs guarding against pinch points.

68

What is the difference between welding, brazing and soldering?

Welding joins metals by melting the base metals (with or without filler) so they fuse together, producing the strongest joints. Brazing joins metals using a filler metal that melts above 450 °C but below the melting point of the base metals; the filler flows into the joint by capillary action. Soldering is similar but uses a filler that melts below 450 °C, giving lower-strength joints mainly for electrical connections and light-duty sealing.

Read full answer

Applies toMechanical engineering (manufacturing, joining processes)

Comparison

Aspect Welding Brazing Soldering
Base metal melts? Yes No No
Filler melting point Similar to base metal Above 450 °C Below 450 °C
Typical temperature Above about 1,450 °C for steel About 600–1,100 °C About 180–300 °C
Joint strength Highest (equal to base metal when done well) Medium–high Low
Heat distortion High Moderate Low
Joining dissimilar metals Difficult Easy Easy
Filler metals Same family as base metal Copper, brass, silver alloys, aluminium-silicon Tin-lead (63/37, melts 183 °C), lead-free SAC305 (about 217–220 °C)
Flux Shielding gas or flux coating Borax-type fluxes Rosin or acid fluxes
Uses Structures, pipelines, vehicles Copper tubing in HVAC, carbide tool tips, bicycle frames, radiators Electronics (PCBs), plumbing, wiring

Worked Example: Brazed Lap Joint Strength

Answer: the joint can carry about 30 kN, more than the 12 kN the sheet can carry, so the sheet fails first. Two 2 mm steel sheets 20 mm wide are brazed in a 10 mm lap joint; braze shear strength is 150 MPa and sheet tensile strength is 300 MPa.

  1. Braze shear area = 10 × 20 = 200 mm² → joint strength = 200 × 150 = 30,000 N

  2. Sheet strength = 2 × 20 × 300 = 12,000 N

A common design rule is a lap length of about three times the thinner member’s thickness.

Advantages of Brazing and Soldering

  • Low temperature, less distortion and metallurgical damage.

  • Joins dissimilar and thin materials.

  • Neat, leak-tight joints with good capillary filling.

Limitations

  • Lower strength at high temperature (filler softens).

  • Joint clearance must be controlled (typically about 0.025–0.125 mm for brazing).

  • Surfaces must be very clean.

69

What are the common machining operations on a lathe?

A lathe rotates the workpiece while a single-point cutting tool removes material to produce cylindrical and related shapes. Common operations are facing, straight (plain) turning, step turning, taper turning, chamfering, grooving, parting off, thread cutting, knurling, drilling, boring and reaming.

Read full answer

Applies toMechanical engineering (machining)

Lathe Operations

Operation Description
Facing Machining the end face flat, tool moving perpendicular to the axis
Plain (straight) turning Reducing diameter along the length
Step turning Turning different diameters in steps
Taper turning Producing a conical surface (compound rest, tailstock offset, taper attachment, CNC)
Chamfering Bevelling edges
Grooving / necking Cutting a narrow groove (e.g. for circlips, thread relief)
Parting off Cutting the finished part off the bar
Thread cutting Cutting external or internal threads using a lead screw and change gears (or CNC)
Knurling Pressing a diamond or straight pattern for grip
Drilling Drill in the tailstock; workpiece rotates
Boring Enlarging an existing hole with a boring bar
Reaming Finishing a hole to accurate size
Eccentric turning Turning off-centre features (cranks)

Worked Example: Taper Turning

Answer: set the compound rest to about 2.86°, or offset the tailstock by 15 mm. A taper runs from 50 mm to 40 mm diameter over 100 mm length on a 300 mm long workpiece.

  1. Compound rest angle: tan α = (D − d) / (2L) = (50 − 40) / (2 × 100) = 0.05 → α ≈ 2.86°

  2. Tailstock offset (if the taper is turned between centres): offset = (D − d) × L_total / (2L) = 10 × 300 / 200 = 15 mm

The compound rest method suits short, steep tapers; tailstock offset suits long, gentle tapers; a taper turning attachment or CNC is used for production.

Main Lathe Parts

Bed, headstock (spindle, gearbox), tailstock, carriage (saddle, cross slide, compound rest, tool post, apron), lead screw and feed rod, chuck (three-jaw self-centring, four-jaw independent) or collet.

Types of Lathes

Centre (engine) lathe, capstan and turret lathes (repetitive production), automatic lathes, and CNC lathes/turning centres (most production today).

Safety Tips

Remove the chuck key before starting, use guards, wear goggles, keep sleeves and hair secured, never measure a rotating workpiece, and use chip hooks rather than hands to clear chips.

70

What are cutting speed, feed and depth of cut?

Cutting speed (V) is the relative surface speed between the tool and the workpiece, in m/min: V = πDN / 1,000 (D in mm, N in rpm). Feed (f) is the distance the tool advances per revolution of the workpiece (mm/rev) or per tooth (milling, mm/tooth). Depth of cut (d) is the thickness of material removed in one pass, measured perpendicular to the machined surface (mm). Together they are the cutting parameters that set productivity, surface finish, tool life and power.

Read full answer

Applies toMechanical engineering (machining)

Key Formulas (Turning)

  • Spindle speed: N = 1,000V / (πD)

  • Material removal rate: MRR = V × f × d × 1,000 (mm³/min, V in m/min)

  • Machining time: t = L / (f × N) (min)

  • Cutting power: P = MRR × specific cutting energy

Worked Example

Answer: set about 630 rpm; MRR = 40 cm³/min, time ≈ 1.6 min per pass, power ≈ 1.3 kW. A 50 mm diameter steel bar is turned at a cutting speed of 100 m/min, feed 0.2 mm/rev and depth of cut 2 mm, over a length of 200 mm. Take specific cutting energy as 2 J/mm³.

  1. N = 1,000 × 100 / (π × 50) ≈ 637 rpm → nearest machine speed 630 rpm

  2. MRR = 100 × 0.2 × 2 × 1,000 = 40,000 mm³/min (40 cm³/min)

  3. Time = 200 / (0.2 × 630) ≈ 1.59 min

  4. Power = (40,000 / 60) × 2 ≈ 1,333 W ≈ 1.3 kW (at the tool; motor power is higher after efficiency)

Typical Cutting Speeds (Carbide Tools, Turning)

Work material Approximate V (m/min)
Mild steel 150–250
Alloy steel 100–200
Stainless steel 80–180
Cast iron 100–200
Aluminium 300–1,000 or more
HSS tools (steel) About 25–40

Effect of Each Parameter

Parameter Increase gives Main effect on
Cutting speed Higher MRR, more heat Tool life (most sensitive), surface finish
Feed Higher MRR Surface roughness (Ra ≈ f² / (32r) for nose radius r), cutting force
Depth of cut Higher MRR Cutting force and power; little effect on tool life

Selection Practice

  • Roughing: large depth of cut and feed, moderate speed (maximise MRR).

  • Finishing: small depth and feed, higher speed (good surface finish and accuracy).

  • Use tool manufacturer recommendations, then optimise for machine power, rigidity and tool life.

71

What is tool wear, and what is Taylor's tool life equation?

Tool wear is the gradual loss of material and change of shape of a cutting tool’s edge during machining, caused by friction, high temperature and chemical interaction with the workpiece and chips. It reduces accuracy and surface finish and increases cutting forces until the tool must be changed. Taylor’s tool life equation, V·Tⁿ = C, relates cutting speed (V) to tool life (T): faster cutting shortens tool life sharply.

Read full answer

Applies toMechanical engineering (machining)

Types of Tool Wear

Type Location Cause
Flank wear Clearance (flank) face Abrasion against the machined surface; main criterion for tool life (e.g. average VB = 0.3 mm)
Crater wear Rake face Diffusion and chemical wear from hot chips (high speeds)
Notch wear At depth-of-cut line Work-hardened surface, scale
Edge chipping Cutting edge Mechanical shock, interrupted cuts
Built-up edge (BUE) Rake face near edge Work material welding to tool at low speeds
Plastic deformation Edge Excessive heat and pressure
Thermal cracking Edge Thermal cycling (milling, coolant)

Wear Mechanisms

Abrasion, adhesion, diffusion, oxidation and fatigue.

Taylor’s Equation

V·Tⁿ = C - V = cutting speed (m/min), T = tool life (min) - n = exponent (HSS about 0.1–0.15; carbide about 0.2–0.3; ceramics about 0.4–0.6) - C = speed for 1 minute of tool life

Worked Example 1: Effect of Speed

Answer: tool life rises from 16 minutes to about 39 minutes when speed drops from 150 to 120 m/min. A carbide tool has n = 0.25 and C = 300 m/min.

  • At 150 m/min: T = (300 / 150)^(1/0.25) = 2⁴ = 16 min

  • At 120 m/min: T = (300 / 120)⁴ = 2.5⁴ ≈ 39 min

A 20% cut in speed gives about 2.4 times the tool life.

Worked Example 2: Finding n and C From Tests

Answer: n ≈ 0.226 and C ≈ 253 m/min. Tests give T = 60 min at 100 m/min and T = 10 min at 150 m/min.

  1. n = ln(V₂/V₁) / ln(T₁/T₂) = ln(1.5) / ln(6) ≈ 0.4055 / 1.7918 ≈ 0.226

  2. C = 100 × 60^0.226 ≈ 100 × 2.53 ≈ 253 m/min

Extended Taylor Equation

V·Tⁿ·f^a·d^b = C, which includes feed (f) and depth of cut (d); speed has the strongest effect, then feed, then depth.

Reducing Tool Wear

Correct speeds and feeds, coated carbide tools (TiN, TiAlN, Al₂O₃), proper coolant, rigid setups, and suitable tool geometry.

72

What is CNC machining?

CNC (computer numerical control) machining is an automated manufacturing process in which a computer controls the movements of machine tools (lathes, milling machines, routers, grinders, EDM and laser cutters) by following a coded program, usually G-code and M-code. It produces parts with high accuracy, repeatability and complexity, with little manual intervention.

Read full answer

Applies toMechanical engineering (manufacturing and CAD/CAM)

Main Components

Component Function
Machine control unit (MCU) Reads and executes the program (Fanuc, Siemens, Haas, Mitsubishi controllers)
Drive system Servo motors with ball screws and linear guides move each axis
Feedback devices Encoders and linear scales measure position (closed loop)
Spindle Rotates the tool (milling) or workpiece (turning)
Tool changer and turret Automatic tool changes
Coolant and chip handling Cooling, lubrication, chip removal

Common Codes

Code Meaning
G00 Rapid positioning
G01 Linear interpolation (cutting feed)
G02 / G03 Circular interpolation (clockwise / anticlockwise)
G17/G18/G19 Plane selection
G20 / G21 Inch / metric units
G90 / G91 Absolute / incremental programming
G41 / G42 Cutter radius compensation
M03 / M04 / M05 Spindle CW / CCW / stop
M06 Tool change
M08 / M09 Coolant on / off
M30 Program end and reset

Example line (turning): G01 X50.0 Z−30.0 F0.2 moves the tool in a straight line to diameter 50 mm at Z = −30 mm at a feed of 0.2 mm/rev.

Worked Example: Positioning Resolution

Answer: 0.0005 mm (0.5 µm) per encoder count. An axis uses a ball screw with 5 mm pitch, directly coupled to a servo motor with an encoder of 10,000 counts per revolution.

Resolution = 5 mm / 10,000 = 0.0005 mm

Actual accuracy is lower (often about ±0.005–0.01 mm on general machines) because of screw errors, thermal growth and backlash, which are compensated in the controller.

Workflow

CAD model → CAM software (toolpaths, tools, speeds) → post-processor generates G-code → simulation and verification → machine setup (work offsets, tool offsets) → machining → inspection.

Advantages and Limitations

  • Advantages: high precision, repeatability, complex 3D shapes (3-, 4-, 5-axis), less skilled operator effort, flexibility to change programs.

  • Limitations: high capital cost, skilled programmers needed, setup time for small batches.

73

What is the difference between forging, rolling, extrusion and drawing?

Forging, rolling, extrusion and drawing are bulk metal forming processes that shape metal by plastic deformation without removing material. Forging shapes metal by compressive forces from hammers or presses, often in dies. Rolling reduces thickness by passing metal between rotating rolls. Extrusion pushes metal through a die opening to make long products of constant cross-section. Drawing pulls metal through a die to reduce its diameter (wire, rods, tubes).

Read full answer

Applies toMechanical engineering (manufacturing processes)

Comparison

Aspect Forging Rolling Extrusion Drawing
Force type Compression (hammer or press) Compression between rolls Compression (push through die) Tension (pull through die)
Products Discrete parts: crankshafts, connecting rods, gears, flanges, hand tools Plates, sheets, strips, bars, rails, I-beams Constant section profiles: aluminium window sections, tubes, rods Wires, thin rods, tubes
Hot or cold Both Both (hot for ingots/slabs, cold for finishing) Both (aluminium often hot) Mainly cold
Reduction per pass Large Moderate (limited by friction and roll size) Very large (high extrusion ratios) Limited (typically about 20–45% area per pass)
Grain structure Grain flow follows part shape (high fatigue strength) Elongated in rolling direction Elongated along length Elongated, work-hardened

Worked Example 1: Maximum Draft in Rolling

Answer: about 3 mm per pass. Rolls of radius 300 mm with a coefficient of friction of 0.1.

Δh_max = µ² × R = 0.1² × 300 = 3 mm

Worked Example 2: Extrusion Ratio

Answer: extrusion ratio 16 and true strain about 2.77. A 100 mm diameter billet is extruded into a 25 mm rod.

  • R = A₀ / A_f = (100 / 25)² = 16

  • True strain = ln 16 ≈ 2.77

  • Length increases 16 times (volume constant)

Worked Example 3: Wire Drawing Limit

In ideal, frictionless drawing of a perfectly plastic material, the maximum area reduction per pass is about 63% (1 − 1/e), because beyond this the drawing stress exceeds the strength of the drawn wire. Real limits are lower, so wires are drawn through several dies in sequence.

Hot vs Cold Working

  • Hot working (above recrystallisation temperature): lower forces, large deformation, scale and lower accuracy.

  • Cold working: better surface finish, accuracy and strength (work hardening), but higher forces and less ductility; annealing may be needed between passes.

74

What is sheet metal working?

Sheet metal working is the group of processes that cut and form thin metal sheets (typically about 0.5–6 mm thick) into useful parts, mainly using presses, punches and dies. The main operations are shearing (blanking, punching, piercing, notching, trimming), bending (V-bending, flanging, hemming), drawing (deep drawing, stretch forming), and other forming such as embossing, coining and spinning. It is used to make car body panels, appliance housings, enclosures, utensils and aircraft skins.

Read full answer

Applies toMechanical engineering (manufacturing processes)

Main Operations

Operation Description
Blanking Cutting out a piece (the blank is the product)
Punching / piercing Making holes (the cut-out slug is scrap)
Notching, lancing, trimming Cutting edges, partial cuts, removing excess
Bending Forming along a straight line (press brake)
Deep drawing Forming cups or boxes from flat blanks
Stretch forming Stretching over a die (aircraft panels)
Embossing / coining Raised designs; coins with precise detail
Spinning Forming axisymmetric parts on a rotating mandrel
Roll forming Continuous bending into profiles

Worked Example 1: Punching Force

Answer: about 94 kN. Punch a 50 mm diameter hole in 2 mm steel sheet with shear strength 300 MPa.

F = L × t × τ = (π × 50) × 2 × 300 ≈ 157.1 × 600 ≈ 94,250 N ≈ 94 kN

Die clearance is typically about 5–10% of sheet thickness per side (here about 0.1–0.2 mm).

Worked Example 2: Bend Allowance

Answer: about 5.75 mm. A 90° bend in 2 mm sheet with an inside radius of 3 mm and K-factor 0.33.

BA = θ × (R + K·t) = (π/2) × (3 + 0.33 × 2) ≈ 1.5708 × 3.66 ≈ 5.75 mm

Worked Example 3: Blank Diameter for a Cup

Answer: about 102.5 mm. A cup 50 mm in diameter and 40 mm deep (thin sheet, no flange, small corner radius).

D = √(d² + 4dh) = √(50² + 4 × 50 × 40) = √(2,500 + 8,000) ≈ 102.5 mm

The draw ratio D/d ≈ 2.05 is right at the typical limit (about 2) for one draw, so two draws might be planned.

Common Defects

Burrs (wrong clearance), springback in bending, wrinkling and tearing in deep drawing, earing (anisotropy), cracking at tight bends.

Equipment

Mechanical and hydraulic presses, press brakes, turret punch presses, CNC laser and plasma cutters, progressive and transfer dies for high-volume production.

75

What is 3D printing (additive manufacturing)?

3D printing (additive manufacturing, AM) builds parts layer by layer directly from a 3D CAD model, adding material only where needed instead of removing it from a solid block. It allows complex geometries (internal channels, lattices), rapid prototyping and customised or low-volume parts without tooling.

Read full answer

Applies toMechanical engineering (manufacturing and CAD/CAM)

Main Processes (ISO/ASTM 52900 Categories)

Process Material How it works Typical uses
FDM/FFF (material extrusion) Thermoplastics (PLA, ABS, PETG, nylon, carbon-filled) Heated nozzle extrudes filament Prototypes, jigs and fixtures
SLA / DLP (vat photopolymerisation) Photopolymer resins UV laser or projector cures resin Dental models, fine detailed parts
SLS (powder bed fusion, polymer) Nylon powders Laser sinters powder Functional plastic parts
DMLS / SLM (powder bed fusion, metal) Titanium, Inconel, stainless steel, aluminium Laser melts metal powder Aerospace brackets, medical implants, conformal-cooled moulds
Binder jetting Metal, sand, ceramics Binder glues powder, then sintering Sand moulds, metal parts
Material jetting Photopolymers Inkjet heads deposit droplets Multi-colour prototypes
DED (directed energy deposition) Metal wire/powder Laser or arc melts feed Repair, large metal parts

Process Chain

CAD model → STL/3MF file → slicing (layer height, infill, supports) → printing → post-processing (support removal, curing, heat treatment, machining, finishing) → inspection.

Worked Example: FDM Print Time and Material

Answer: about 3.5 hours at 100% fill, using about 62 g of PLA. A 50 cm³ solid part is printed with a 0.4 mm nozzle, 0.2 mm layers and a print speed of 50 mm/s.

  1. Volumetric flow = 0.4 × 0.2 × 50 = 4 mm³/s

  2. Time = 50,000 mm³ / 4 ≈ 12,500 s ≈ 3.5 hours (travel moves add time; 20% infill with walls would cut this substantially)

  3. Mass = 50 cm³ × 1.24 g/cm³ (PLA) ≈ 62 g

Advantages

  • Complex shapes, part consolidation, lightweight lattices (topology optimisation).

  • No tooling: fast, economical for prototypes and small batches.

  • Customisation (medical implants, dental aligners).

Limitations

  • Slower and costlier than moulding or casting for large volumes.

  • Anisotropic properties (weaker between layers in FDM), surface roughness, support marks.

  • Size limits and post-processing requirements.

76

What are tolerances, allowances and fits?

Tolerance is the permitted variation in a dimension: the difference between its upper and lower limits. Allowance is the intentional difference between the maximum material limits of mating parts: the minimum clearance (positive allowance) or maximum interference (negative allowance). A fit is the relationship between mating parts (usually a hole and a shaft) that results from their tolerances, and is classified as clearance, transition or interference.

Read full answer

Applies toMechanical engineering (metrology and machine design; ISO 286 / IS 919)

Types of Fits

Fit Condition Examples
Clearance Shaft always smaller than hole Running and sliding fits: H7/g6, H8/f7, H9/d9
Transition May give clearance or interference Locational fits: H7/k6, H7/n6
Interference Shaft always larger than hole Press and shrink fits: H7/p6, H7/s6

Hole-Basis System

Most industries use the hole-basis system (hole tolerance H, lower deviation = 0) because holes are made with fixed-size tools (drills, reamers), while shafts are easier to machine to different sizes.

Worked Example 1: 50 H7/g6 (Clearance Fit)

Answer: clearance between 0.009 mm and 0.050 mm. From ISO 286 for 50 mm: H7 = +0.025/0, g6 = −0.009/−0.025.

  • Hole: 50.000 to 50.025 mm; shaft: 49.975 to 49.991 mm

  • Maximum clearance = 50.025 − 49.975 = 0.050 mm

  • Minimum clearance (allowance) = 50.000 − 49.991 = 0.009 mm

Worked Example 2: 50 H7/p6 (Interference Fit)

Answer: interference between 0.001 mm and 0.042 mm. p6 = +0.042/+0.026.

  • Shaft: 50.026 to 50.042 mm

  • Maximum interference = 50.042 − 50.000 = 0.042 mm

  • Minimum interference = 50.026 − 50.025 = 0.001 mm

Key Terms

  • Basic size: nominal size (50 mm).

  • Deviation: difference between limit and basic size.

  • Fundamental deviation: the deviation closest to the basic size (letter code).

  • IT grade: tolerance grade (IT6 = 16 µm and IT7 = 25 µm for 30–50 mm). Lower IT numbers mean tighter tolerances.

Typical Uses

Fit Application
H7/g6 Sliding gears, pistons in hydraulic valves
H7/h6 Locational clearance (spigots)
H7/k6 Gears and pulleys with keys, bearing inner races on rotating shafts (light loads)
H7/p6 Bushes pressed into housings
H7/s6 Permanent shrink fits (couplings, wheel hubs)

Tighter tolerances cost more, so the widest tolerance that meets function should be chosen.

77

What is GD&T?

GD&T (Geometric Dimensioning and Tolerancing) is a standard symbolic language on engineering drawings that defines the allowable variation in form, orientation, location and runout of part features, relative to datums. It communicates design intent precisely, ensures parts assemble and function, and often allows larger, cheaper tolerances than plus-minus dimensioning. The main standards are ASME Y14.5 and ISO 1101 (with related ISO GPS standards).

Read full answer

Applies toMechanical engineering (design, drafting and metrology)

Categories and Symbols

Category Characteristics Datum needed?
Form Straightness, flatness, circularity, cylindricity No
Orientation Perpendicularity, parallelism, angularity Yes
Location Position, concentricity, symmetry (ASME 2018 removed concentricity and symmetry; ISO keeps them) Yes
Profile Profile of a line, profile of a surface Optional
Runout Circular runout, total runout Yes

Feature Control Frame

Example: ⌖ | Ø0.2 Ⓜ | A | B | C

Read as: “Position tolerance of 0.2 mm diameter at maximum material condition, relative to datums A, B and C.”

Datums

Datum A (primary) is usually a large flat face (3 points of contact), B (secondary) a side face (2 points), C (tertiary) a third face or hole (1 point), establishing the datum reference frame.

Worked Example 1: Bonus Tolerance at MMC

Answer: total position tolerance Ø0.3 mm. A hole Ø10.0–10.2 mm has a position tolerance of Ø0.2 at MMC; the produced hole measures Ø10.1.

  • MMC of the hole = Ø10.0 (smallest hole)

  • Bonus = 10.1 − 10.0 = 0.1 mm

  • Allowed position tolerance = 0.2 + 0.1 = Ø0.3 mm

Worked Example 2: Square vs Circular Tolerance Zone

Answer: a circular zone of Ø0.283 mm gives about 57% more usable area than a ±0.1 mm square zone. A ±0.1 mm coordinate tolerance creates a 0.2 × 0.2 mm square zone (area 0.04 mm²). Its diagonal is 0.283 mm, so the circle through the corners (Ø0.283) has area π × 0.1414² ≈ 0.0628 mm², which accepts functionally good parts rejected by coordinate tolerancing.

Benefits

  • Clear functional requirements, less ambiguity between design, manufacturing and inspection.

  • Larger effective tolerances (round zones, bonus tolerance), lowering cost.

  • Consistent inspection with CMMs and functional gauges.

78

What are vernier calipers, micrometers and CMMs used for?

Precision measuring instruments measure dimensions accurately for inspection and quality control. A vernier caliper measures outside, inside and depth dimensions, typically to 0.02 mm (or 0.01 mm digital). A micrometer measures smaller ranges more precisely, typically to 0.01 mm (0.001 mm for high-resolution types). A CMM (coordinate measuring machine) measures complex 3D geometry and GD&T features using a probe, with accuracy of a few micrometres.

Read full answer

Applies toMechanical engineering (metrology)

Comparison

Instrument Typical least count Range Uses
Steel rule 0.5–1 mm Up to 1 m or more Rough measurements
Vernier caliper 0.02 mm (0.05 mm on some) 0–150/200/300 mm or more General OD, ID, depth, steps
Digital caliper 0.01 mm Similar Quick shop-floor measurement
Outside micrometer 0.01 mm (0.001 mm vernier/digital) 25 mm ranges (0–25, 25–50, …) Shaft diameters, thickness
Bore gauge / inside micrometer 0.001–0.01 mm Various Bores and holes
Dial indicator 0.01 mm (0.001 mm types) Small travel Runout, flatness, alignment
Height gauge 0.01–0.02 mm Up to about 600 mm Marking and heights on surface plates
Slip (gauge) blocks Calibration standards Various Calibrating instruments
CMM About 1–5 µm Large volumes Complex parts, GD&T, first article inspection

Worked Example 1: Vernier Caliper

Answer: least count 0.02 mm; reading 24.34 mm. On a caliper, 50 vernier divisions match 49 mm on the main scale. The zero of the vernier is just past 24 mm, and the 17th vernier division lines up.

  1. Least count = 1 MSD − 1 VSD = 1 − 49/50 = 0.02 mm

  2. Reading = 24 + 17 × 0.02 = 24.34 mm

Worked Example 2: Micrometer

Answer: least count 0.01 mm; reading 12.73 mm. A micrometer has a 0.5 mm pitch spindle and 50 thimble divisions. The sleeve shows 12.5 mm and the thimble line 23 aligns with the datum.

  1. Least count = 0.5 / 50 = 0.01 mm

  2. Reading = 12.5 + 23 × 0.01 = 12.73 mm

If the micrometer reads +0.02 mm with anvils closed (positive zero error), the corrected reading is 12.71 mm.

Good Measurement Practice

  • Clean the instrument and part; check zero before use.

  • Use constant, light measuring force (micrometer ratchet).

  • Measure at 20 °C reference temperature when possible.

  • Calibrate instruments regularly (traceable to national standards, NABL-accredited labs in India).

  • Rule of thumb: instrument resolution should be about one-tenth of the tolerance being checked.

79

What are lean manufacturing, Six Sigma and TPM?

Lean manufacturing focuses on eliminating waste and improving flow so that only value-adding work is done, based on the Toyota Production System. Six Sigma is a data-driven method for reducing process variation and defects, aiming at no more than 3.4 defects per million opportunities, using the DMAIC cycle. TPM (Total Productive Maintenance) aims to maximise equipment effectiveness by involving all employees, especially operators, in maintenance, targeting zero breakdowns, zero defects and zero accidents.

Read full answer

Applies toMechanical engineering (industrial engineering and operations)

Lean Manufacturing

  • Eight wastes (TIMWOODS): Transport, Inventory, Motion, Waiting, Overproduction, Over-processing, Defects, Skills not used.

  • Tools: value stream mapping, 5S, kanban, just-in-time, SMED (quick changeover), poka-yoke (error proofing), kaizen, standard work, takt time.

Six Sigma

  • DMAIC: Define, Measure, Analyse, Improve, Control.

  • Tools: SIPOC, process capability (Cp, Cpk), measurement system analysis (Gauge R&R), Pareto charts, fishbone diagrams, hypothesis tests, DOE, control charts.

  • Belts: Yellow, Green, Black, Master Black Belt.

TPM: Eight Pillars

Autonomous maintenance, planned maintenance, focused improvement (kobetsu kaizen), quality maintenance, early equipment management, training and education, safety-health-environment, and office TPM.

Worked Example 1: OEE

Answer: OEE ≈ 75%. A machine has 480 minutes planned, 60 minutes downtime, an ideal cycle time of 1 minute per part, 380 parts produced and 361 good parts.

  1. Availability = (480 − 60) / 480 = 0.875

  2. Performance = (380 × 1) / 420 ≈ 0.905

  3. Quality = 361 / 380 = 0.95

  4. OEE = 0.875 × 0.905 × 0.95 ≈ 0.752 (75.2%)

World-class OEE is often quoted as about 85%.

Worked Example 2: DPMO and Sigma Level

Answer: 1,250 DPMO, about 4.5 sigma. 5,000 units were inspected, each with 4 defect opportunities, and 25 defects were found.

  • DPMO = 25 / (5,000 × 4) × 1,000,000 = 1,250

  • From the sigma table (with 1.5σ shift), 1,350 DPMO ≈ 4.5σ, so this process is about 4.5 sigma

How They Fit Together

Lean improves speed and flow, Six Sigma improves quality and consistency (Lean Six Sigma combines both), and TPM ensures the equipment is reliable enough to support both.

80

Which CAD software have you used, and what did you design with it?

This question checks your hands-on design skills and how you apply them, not just the names of tools. A strong answer names the software and version you actually used, describes one specific project (what you designed, your role, the constraints), explains the features you used (parametric modelling, assemblies, drawings, simulation), and gives a measurable result. Be honest; interviewers often follow up with practical questions or a short test.

Read full answer

Applies toMechanical engineering (design interviews)

Common CAD Software

Software Typical use
SolidWorks Machine design, product design, SMEs; strong assemblies, sheet metal, weldments, Simulation
CATIA (3DEXPERIENCE) Automotive and aerospace (surfaces, large assemblies)
Siemens NX Automotive, aerospace, tooling; integrated CAM
PTC Creo Industrial machinery, heavy engineering
Autodesk Inventor Machinery, factory design
Fusion 360 Start-ups, students, integrated CAD/CAM/CAE
AutoCAD 2D drafting, layouts, plant drawings
ANSYS / Abaqus (CAE) Simulation and analysis

Structure for Your Answer

  1. Software and level: “I’ve used SolidWorks for about two years and AutoCAD for 2D layouts.”

  2. Project context: what the part or assembly did and its constraints.

  3. Your work: modelling approach, assemblies, drawings with GD&T, simulation.

  4. Result with a number: weight reduced, cost saved, factor of safety achieved, time saved.

  5. What you learned or would improve.

Sample Answer (Adapt to Your Real Experience)

“In my final-year project I used SolidWorks to design a mounting bracket for a 25 kg motor. I built a parametric model, checked fit in an assembly with the motor and frame, and ran a static study in SolidWorks Simulation. The first version had a factor of safety of 6, so I added ribs and pockets and changed the thickness from 8 mm to 6 mm. The final design kept a factor of safety above 3 while reducing mass from 1.2 kg to 0.85 kg, about 29% lighter. I made manufacturing drawings with tolerances for laser cutting and bending, and the part was fabricated and fitted without changes.”

Check the numbers you quote: 1.2 to 0.85 kg is a reduction of 0.35 / 1.2 ≈ 29%.

Tips

  • Mention design for manufacturing: tolerances, standard parts, materials, cost.

  • If you used simulation, say what loads and boundary conditions you assumed.

  • Mention file formats and collaboration: STEP exports, PDM, design reviews.

  • Keep a portfolio (screenshots, drawings) to show if asked.

  • If you know a different tool than the company uses, say you are confident you can switch, since core modelling concepts transfer.

Sign in to keep reading

You've opened 2 full answers. Sign in to read all 80 Mechanical Engineering answers, mark what you know and pick up where you left off.

Report a mistake

What's wrong?

Test yourself with multiple-choice questions: Mechanical Engineering MCQ questions and answers

All Core Engineering subjects