Skip to content
Core Engineering

Electrical Engineering interview questions and answers

80 questions. About 3 h 11 min to read them all.

By TestLab · Updated

Plan for an interview
80 questions

Track what you know and what to revise.

Sign in to track progress

You can open a few full answers without signing in. Sign in to read all

1

What is Ohm's law?

Ohm’s law states that the current through a conductor is directly proportional to the voltage across it, provided its temperature and other physical conditions stay constant: V = I × R, where V is voltage in volts (V), I is current in amperes (A) and R is resistance in ohms (Ω).

Read full answer

Applies toElectrical engineering (circuit theory)

Forms of the Equation

  • V = I·R

  • I = V / R

  • R = V / I

Combined with power: P = V·I = I²·R = V² / R (watts).

Worked Example

Answer: 5 A and 1,150 W. A 46 Ω heater element is connected to a 230 V supply.

  • I = V / R = 230 / 46 = 5 A

  • P = V·I = 230 × 5 = 1,150 W (check: I²R = 25 × 46 = 1,150 W)

Graphical Meaning

For an ohmic conductor, the V–I graph is a straight line through the origin; its slope (V/I) is the resistance.

Resistance and Resistivity

R = ρ·L / A

  • ρ = resistivity (Ω·m): copper ≈ 1.72 × 10⁻⁸ Ω·m, aluminium ≈ 2.82 × 10⁻⁸ Ω·m

  • L = length (m), A = cross-sectional area (m²)

Example: 100 m of 2.5 mm² copper wire: R = 1.72 × 10⁻⁸ × 100 / 2.5 × 10⁻⁶ ≈ 0.69 Ω. At 16 A, the voltage drop in one conductor = 16 × 0.69 ≈ 11 V (22 V for the go-and-return path), which is why long cable runs need larger conductors.

Limitations

Ohm’s law does not apply directly to: - Non-linear devices: diodes, transistors, LEDs, arc lamps. - Components whose resistance changes with temperature: filament lamps (cold resistance is much lower than hot resistance), thermistors. - Electrolytes and gases in some conditions. - AC circuits with inductance and capacitance, unless resistance is replaced by impedance (V = I·Z).

Practical Applications

  • Sizing resistors (e.g. LED current-limiting resistors).

  • Calculating cable voltage drop.

  • Checking circuits with a multimeter (unexpected resistance indicates faults).

  • Designing heaters and calculating fuse ratings.

2

What are Kirchhoff's current and voltage laws?

Kirchhoff’s current law (KCL) states that the algebraic sum of currents entering and leaving any node (junction) is zero, so total current in equals total current out. Kirchhoff’s voltage law (KVL) states that the algebraic sum of all voltages around any closed loop is zero, so the sum of voltage rises equals the sum of voltage drops. They are based on conservation of charge and conservation of energy.

Read full answer

Applies toElectrical engineering (circuit theory and network analysis)

KCL (Current Law)

Σ I_in = Σ I_out at any node, or Σ I = 0 taking entering currents as positive and leaving as negative.

Example: 5 A enters a node, and two branches carry 2 A and I₃ away. Then 5 = 2 + I₃ → I₃ = 3 A.

KVL (Voltage Law)

Σ V = 0 around any closed loop: the source EMFs equal the sum of I·R drops.

Worked Example (Series Circuit)

Answer: I = 2 A, with 4 V and 8 V across the resistors. A 12 V battery is connected to resistors R₁ = 2 Ω and R₂ = 4 Ω in series.

  1. KVL: 12 − 2I − 4I = 0 → I = 12 / 6 = 2 A

  2. V₁ = 2 × 2 = 4 V; V₂ = 4 × 2 = 8 V

  3. Check: 12 − 4 − 8 = 0 ✓

Worked Example (Two-Loop Circuit, Mesh Analysis)

Answer: I₁ ≈ 1.35 A and I₂ ≈ 0.58 A. Loop 1 has a 10 V source, a 4 Ω resistor and a shared 6 Ω resistor. Loop 2 has the shared 6 Ω resistor, an 8 Ω resistor and no source. Using mesh currents I₁ and I₂ (both clockwise):

  • Loop 1: 10 = 4I₁ + 6(I₁ − I₂) → 10I₁ − 6I₂ = 10

  • Loop 2: 0 = 6(I₂ − I₁) + 8I₂ → −6I₁ + 14I₂ = 0 → I₁ = 14I₂ / 6 = 2.333I₂

  • Substitute: 10(2.333I₂) − 6I₂ = 10 → 17.33I₂ = 10 → I₂ ≈ 0.577 A, I₁ ≈ 1.346 A

Current in the 6 Ω resistor = I₁ − I₂ ≈ 0.77 A.

Sign Conventions

  • Going from − to + through a source: voltage rise (+); from + to −: drop (−).

  • Going through a resistor in the direction of current: drop (−I·R).

  • If a calculated current is negative, its real direction is opposite to the assumed direction.

Applications

  • Basis of nodal analysis (uses KCL) and mesh analysis (uses KVL).

  • Solving any linear circuit, checking measurements and designing networks.

Limitations

Valid for lumped circuits where dimensions are small compared with the wavelength; at very high frequencies (RF, long transmission lines), distributed models are needed.

3

What is the difference between AC and DC?

DC (direct current) flows in one direction only with a constant (or nearly constant) magnitude, like the output of a battery or solar panel. AC (alternating current) periodically reverses direction, usually following a sine wave; in India the mains supply is 230 V, 50 Hz single-phase and 415 V three-phase.

Read full answer

Applies toElectrical engineering (AC and DC fundamentals)

Comparison

Aspect AC DC
Direction Reverses periodically One direction
Waveform Sinusoidal (usually) Constant (flat)
Frequency 50 Hz (India, Europe), 60 Hz (USA) 0 Hz
Sources Alternators, inverters Batteries, solar cells, rectifiers, DC generators
Voltage change Easy with transformers Needs DC-DC converters
Transmission Economical over distance with transformers; HVDC for very long distances Used in HVDC links
Passive elements Inductors and capacitors have reactance Inductor = short, capacitor = open (steady state)
Power factor Applies Not applicable
Storage Cannot be stored directly Can be stored in batteries
Typical uses Homes, industry, motors, grid Electronics, EVs, telecom, battery systems, data centres (increasingly)

Key AC Quantities

  • Frequency (f): cycles per second (Hz). Period T = 1/f; for 50 Hz, T = 20 ms.

  • Peak (maximum) value V_m and RMS value: V_rms = V_m / √2 for a sine wave.

  • Instantaneous value: v = V_m·sin(2πft).

  • Phase: angular position; phase difference between voltage and current depends on the load.

Worked Example

Answer: peak voltage ≈ 325 V, and the supply reverses direction 100 times per second. The Indian mains is 230 V rms at 50 Hz.

  • V_m = 230 × √2 ≈ 325.3 V

  • Peak-to-peak = 650.5 V

  • Period = 1 / 50 = 20 ms; current changes direction twice per cycle → 100 times per second

  • Instantaneous voltage 2.5 ms after a zero crossing: v = 325.3 × sin(2π × 50 × 0.0025) = 325.3 × sin 45° ≈ 230 V

Why Both Are Used

  • AC dominates generation and distribution because transformers make voltage conversion cheap and efficient, and AC induction motors are rugged and simple.

  • DC is required by electronics (phones, computers, LEDs), batteries and many modern loads, so AC is rectified to DC inside chargers and power supplies.

  • Solar panels and batteries produce DC; inverters convert it to AC for the grid.

Safety Note

Both are dangerous. AC at 50 Hz is particularly hazardous because it can cause ventricular fibrillation at fairly low currents (tens of milliamps through the body), which is why RCDs/RCCBs with 30 mA trip ratings are used for personal protection.

4

Why is AC used for power transmission instead of DC?

AC became the standard for power transmission because its voltage can be stepped up and down easily and efficiently with transformers. Transmitting at high voltage reduces current, and therefore I²R losses, so power can be sent over long distances cheaply, then stepped down safely for consumers. AC also suits simple, rugged generators and induction motors, and AC circuit breakers interrupt current more easily because current naturally passes through zero every half cycle.

Read full answer

Applies toElectrical engineering (power systems)

Main Reasons

  1. Easy voltage transformation: transformers (with efficiencies around 98–99.5%) change AC voltage levels; DC needs power-electronic converters.

  2. Lower losses at high voltage: P_loss = I²R, and for the same power I = P / (√3·V·cos φ), so raising voltage reduces current.

  3. Simple generation: alternators are efficient and robust.

  4. Simple loads: induction motors run directly from AC.

  5. Easier switching and protection: AC current crosses zero 100 times per second at 50 Hz, helping arc extinction in breakers.

  6. Easy distribution: multiple voltage levels and tapping points.

Worked Example: Effect of Voltage on Losses

Answer: losses fall by a factor of 400 when the voltage is raised from 11 kV to 220 kV. Transmit 100 MW (three-phase, unity power factor) over a line with 5 Ω resistance per phase.

  • At 11 kV: I = 100 × 10⁶ / (√3 × 11,000) ≈ 5,249 A → losses = 3 × 5,249² × 5 ≈ 413 MW (more than the power sent, so impossible in practice)

  • At 220 kV: I = 100 × 10⁶ / (√3 × 220,000) ≈ 262.4 A → losses = 3 × 262.4² × 5 ≈ 1.03 MW (about 1%)

  • Ratio = (220 / 11)² = 400

This is why generation at about 11–25 kV is stepped up to 220–765 kV for long-distance transmission.

Where DC (HVDC) Is Better

Situation Why HVDC
Very long distances (often beyond about 500–800 km overhead) No reactive power or charging current, lower line cost per km
Undersea and underground cables AC cable charging current becomes very large
Connecting asynchronous grids Links grids of different frequency or phase
Bulk power with controlled flow Precise control of power flow

India operates HVDC links such as Raigarh–Pugalur (±800 kV) and Champa–Kurukshetra (±800 kV).

Disadvantages of AC Transmission

  • Reactive power and voltage control needed (Ferranti effect on long lines).

  • Skin effect increases effective resistance.

  • Stability limits on very long lines.

  • Higher insulation for peak voltage (√2 times rms).

Interview Tip

The key line: “Transformers make it easy to raise AC voltage, which cuts current and I²R losses.” Then mention HVDC as the modern exception for very long or undersea links.

5

What is the difference between voltage, current, power and energy?

Voltage is the electrical potential difference that pushes charge through a circuit (volts, V). Current is the rate of flow of charge (amperes, A). Power is the rate at which electrical energy is converted or used (watts, W = V × A for DC). Energy is the total work done or electricity used over time (joules, or kilowatt-hours for billing).

Read full answer

Applies toElectrical engineering (fundamentals)

Definitions and Units

Quantity Symbol SI unit Definition Formula
Voltage V Volt (V) = J/C Energy per unit charge V = W / Q
Current I Ampere (A) = C/s Charge flow per second I = Q / t
Power P Watt (W) = J/s Energy per second P = V·I (DC); P = V·I·cos φ (AC single-phase)
Energy E Joule (J); kWh Power over time E = P·t

1 kWh = 1,000 W × 3,600 s = 3.6 × 10⁶ J = 1 “unit” on an electricity bill.

Water Analogy

  • Voltage = water pressure.

  • Current = flow rate of water.

  • Resistance = narrowness of the pipe.

  • Power = rate of doing work (pressure × flow).

  • Energy = total work done over time.

Worked Example

Answer: about 6.5 A, 1.5 kW, and 3 kWh (3 units) for 2 hours. A 1.5 kW water heater (geyser) runs on 230 V (resistive, unity power factor).

  • Current I = P / V = 1,500 / 230 ≈ 6.52 A

  • Power = 1.5 kW

  • Energy in 2 hours = 1.5 × 2 = 3 kWh = 3 × 3.6 = 10.8 MJ

  • Resistance = V² / P = 230² / 1,500 ≈ 35.3 Ω

Three-Phase Power

P = √3 × V_L × I_L × cos φ

Example: a motor drawing 20 A at 415 V with power factor 0.85: P = 1.732 × 415 × 20 × 0.85 ≈ 12.2 kW.

Common Confusions

  • kW vs kWh: kW is a rate (like speed); kWh is an amount (like distance).

  • Voltage does not flow: it exists between two points; current flows through a path.

  • High voltage alone is not what makes electricity dangerous: the current through the body (set by voltage and body resistance) causes harm, but higher voltage drives more current through the same resistance.

Practical Use

Appliance ratings (W), cable and breaker sizing (A), supply ratings (V), and bills (kWh) all use these quantities, so engineers move between them constantly.

6

What is the difference between active, reactive and apparent power?

In an AC circuit, active (real) power is the power actually converted into useful work or heat, measured in watts (W). Reactive power is power that flows back and forth between the source and inductors or capacitors to build magnetic and electric fields, measured in volt-amperes reactive (VAR). Apparent power is the product of rms voltage and current, measured in volt-amperes (VA), and is the total power the supply must be rated to carry.

Read full answer

Applies toElectrical engineering (AC power)

Formulas (Single-Phase)

  • Apparent power: S = V·I (VA)

  • Active power: P = V·I·cos φ (W)

  • Reactive power: Q = V·I·sin φ (VAR)

  • Power triangle: S² = P² + Q²

  • Power factor: cos φ = P / S

For three-phase: S = √3·V_L·I_L, P = √3·V_L·I_L·cos φ, Q = √3·V_L·I_L·sin φ.

Power Triangle

  • Horizontal side: P (real power).

  • Vertical side: Q (reactive power; lagging for inductive loads, leading for capacitive).

  • Hypotenuse: S (apparent power).

  • Angle φ between P and S is the phase angle between voltage and current.

Worked Example (Single-Phase)

Answer: S = 2.3 kVA, P = 1.84 kW, Q = 1.38 kVAR. A load draws 10 A from 230 V at power factor 0.8 lagging.

  • S = 230 × 10 = 2,300 VA

  • P = 2,300 × 0.8 = 1,840 W

  • sin φ = √(1 − 0.8²) = 0.6 → Q = 2,300 × 0.6 = 1,380 VAR

  • Check: √(1,840² + 1,380²) = 2,300 ✓

Worked Example (Three-Phase)

A motor draws 20 A at 415 V with PF 0.85: S = 1.732 × 415 × 20 ≈ 14.38 kVA; P = 14.38 × 0.85 ≈ 12.22 kW; Q = 14.38 × 0.527 ≈ 7.58 kVAR.

Comparison

Aspect Active power (P) Reactive power (Q) Apparent power (S)
Unit W, kW, MW VAR, kVAR, MVAR VA, kVA, MVA
Physical meaning Useful work, heat, light Field energy exchange, no net work Total “capacity” used
Produced by Resistance (and mechanical load) Inductors (consume Q), capacitors (supply Q) Combination
Measured by Wattmeter, energy meter (kWh) VAR meter (kVARh) Voltmeter × ammeter

Why Reactive Power Matters

  • Motors and transformers need reactive power to create magnetic fields.

  • It increases current for the same real power, causing more losses and voltage drop.

  • Generators, transformers and cables are rated in kVA/MVA because their heating depends on current, regardless of power factor.

  • Utilities penalise industrial consumers with low power factor; capacitor banks supply reactive power locally.

7

What is power factor, and why is a low power factor bad?

Power factor (PF) is the ratio of active (real) power to apparent power in an AC circuit: PF = P / S = cos φ, where φ is the phase angle between voltage and current. It shows how effectively current is converted into useful power. A low power factor means more current is drawn for the same useful power, which increases losses, voltage drop and equipment size, and attracts penalties from utilities.

Read full answer

Applies toElectrical engineering (AC power and power quality)

Values and Meaning

Power factor Typical loads
1.0 (unity) Resistive loads: heaters, incandescent lamps
0.8–0.9 lagging Loaded induction motors
0.2–0.5 lagging Lightly loaded or idling motors, welding transformers
Leading Over-compensated capacitor banks, lightly loaded cables, over-excited synchronous motors

Lagging PF occurs with inductive loads (current lags voltage); leading PF with capacitive loads.

Worked Example

Answer: current rises from 43.5 A to 72.5 A, and losses rise about 2.78 times. A 10 kW single-phase load on 230 V:

  • At PF 1.0: I = 10,000 / (230 × 1.0) ≈ 43.5 A

  • At PF 0.6: I = 10,000 / (230 × 0.6) ≈ 72.5 A

  • Loss ratio (I²R) = (72.5 / 43.5)² = (1 / 0.6)² ≈ 2.78

The same cable and transformer carry 67% more current at PF 0.6 for the same useful power.

Why Low Power Factor Is Bad

  1. Higher current for the same kW (I = P / (V·cos φ)).

  2. Higher copper losses (I²R) in cables, transformers and generators.

  3. Larger voltage drop, causing poor voltage regulation at the load.

  4. Larger equipment ratings (kVA) for generators, transformers, switchgear and cables.

  5. Reduced system capacity: a 1,000 kVA transformer can supply only 600 kW at PF 0.6 but 950 kW at PF 0.95.

  6. Utility penalties: industrial tariffs in India include power factor surcharges or kVAh billing, and incentives for maintaining high PF (often 0.95 or above).

Causes of Low Power Factor

  • Induction motors, especially lightly loaded ones.

  • Transformers at light load (magnetising current).

  • Arc furnaces, induction furnaces, welding machines.

  • Fluorescent lamp chokes (older magnetic ballasts).

  • Non-linear loads (drives, rectifiers) causing distortion power factor.

True Power Factor With Harmonics

For non-linear loads, true PF = displacement PF × distortion factor. A load can have cos φ ≈ 1 but still a poor true PF because of harmonic current; active filters or PFC circuits are used to correct it.

Interview Tip

Explain the problem in terms of extra current: “The same useful power is delivered with more current, which means more losses and bigger equipment.” Then mention capacitor banks as the standard fix.

8

How can power factor be improved?

Power factor improvement means reducing the reactive power drawn from the supply, usually by installing equipment that supplies reactive power locally to cancel the lagging reactive power of inductive loads. The most common methods are static capacitor banks, automatic power factor correction (APFC) panels, synchronous condensers and active compensators (SVC, STATCOM, active filters).

Read full answer

Applies toElectrical engineering (power systems and industrial installations)

Methods

Method How it works Typical use
Fixed capacitors Capacitors across individual motors or at the panel supply leading kVAR Constant loads, individual motors
APFC panel Controller switches capacitor steps in and out to keep PF near target Factories and commercial buildings with varying loads
Synchronous condenser Over-excited synchronous motor running without load supplies kVAR Large substations, grid support
Phase advancer Supplies excitation to the rotor of slip ring induction motors Large slip ring motors
SVC / STATCOM Power-electronic reactive power compensation, fast and continuous Transmission systems, steel plants, wind farms
Active harmonic filters Correct displacement PF and harmonic distortion Loads with drives and UPS

Capacitor Sizing Formula

Q_c = P × (tan φ₁ − tan φ₂)

where φ₁ is the existing angle and φ₂ the target angle.

Worked Example

Answer: about 69 kVAR, so install a 70 kVAR bank. A 100 kW load operates at PF 0.70 lagging and must be improved to 0.95.

  1. tan φ₁ = tan(cos⁻¹ 0.70) ≈ 1.020

  2. tan φ₂ = tan(cos⁻¹ 0.95) ≈ 0.329

  3. Q_c = 100 × (1.020 − 0.329) ≈ 69.1 kVAR

Effect on current at 415 V three-phase: - Before: I = 100,000 / (1.732 × 415 × 0.70) ≈ 198.8 A - After: I = 100,000 / (1.732 × 415 × 0.95) ≈ 146.4 A - Current falls by about 26%, and cable losses fall by about 46%.

Where to Place Capacitors

Location Advantages Disadvantages
Individual (at each motor) Reduces current in all upstream cables More units, switched with the motor
Group (at distribution boards) Fewer units Less reduction downstream
Central (at main incomer, APFC) Easy control, lowest cost per kVAR Internal cables still carry reactive current

Precautions

  • Avoid over-correction (leading PF), which can cause overvoltage and, in some tariffs, penalties.

  • In systems with drives and other non-linear loads, use detuned reactors with capacitors (e.g. 7% reactors) to avoid harmonic resonance.

  • Size motor capacitors so they do not exceed the motor’s no-load magnetising kVAR (to avoid self-excitation when switched off).

  • Use discharge resistors so capacitors discharge safely.

Other Ways to Improve PF

  • Avoid running motors lightly loaded; size motors correctly.

  • Use energy-efficient motors and electronic ballasts/LED drivers with built-in PFC.

  • Use synchronous motors for large constant-speed drives.

9

What is the RMS value of an AC waveform?

The RMS (root mean square) value of an AC voltage or current is the equivalent DC value that would produce the same heating effect in a resistor. For a sine wave, V_rms = V_m / √2 ≈ 0.707·V_m. When we say Indian mains is 230 V, we mean 230 V rms, so the peak is about 325 V.

Read full answer

Applies toElectrical engineering (AC fundamentals)

Definition

V_rms = √[(1/T) ∫₀ᵀ v(t)² dt]

Take the square of the waveform, average it over one period, then take the square root.

Derivation for a Sine Wave

For v = V_m·sin(ωt): - v² = V_m²·sin²(ωt) = (V_m² / 2)(1 − cos 2ωt) - The average of cos 2ωt over a cycle is zero, so the mean of v² = V_m² / 2 - V_rms = V_m / √2

Related Values (Sine Wave)

Quantity Formula For 230 V rms
Peak (V_m) √2 × V_rms 325.3 V
Peak-to-peak 2V_m 650.5 V
Average (over half cycle) 2V_m / π = 0.637V_m 207.2 V
Form factor V_rms / V_avg = 1.11 1.11
Crest (peak) factor V_m / V_rms = 1.414 1.414

Worked Example

Answer: 1,058 W, the same as 230 V DC. A 50 Ω heater connected to 230 V rms, 50 Hz.

  • P = V_rms² / R = 230² / 50 = 1,058 W

  • I_rms = 230 / 50 = 4.6 A; peak current = 4.6 × 1.414 ≈ 6.5 A

If we wrongly used the peak voltage, we would get 325.3² / 50 ≈ 2,116 W, double the actual power.

Other Waveforms

Waveform RMS value Form factor Crest factor
Sine V_m / √2 1.11 1.414
Square (±V_m) V_m 1.0 1.0
Triangle V_m / √3 1.155 1.732
Half-wave rectified sine V_m / 2 1.57 2.0
Full-wave rectified sine V_m / √2 1.11 1.414

Why RMS Matters

  • Ratings of appliances, cables and breakers are based on RMS values because heating depends on RMS current.

  • Insulation must withstand the peak voltage, so 230 V rms equipment must handle about 325 V peak (plus transients).

  • True RMS meters measure correctly for distorted waveforms (e.g. from drives and SMPS); average-responding meters calibrated for sine waves can read wrongly on non-sinusoidal waveforms.

11

What is resonance in an RLC circuit?

Resonance in an RLC circuit occurs at the frequency where the inductive reactance equals the capacitive reactance (X_L = X_C), so they cancel each other. At this resonant frequency, f₀ = 1 / (2π√(LC)), a series RLC circuit has minimum impedance (equal to R) and maximum current, while a parallel RLC circuit has maximum impedance and minimum line current.

Read full answer

Applies toElectrical engineering (AC circuit theory)

Resonant Frequency

X_L = 2πfL and X_C = 1 / (2πfC). Setting them equal:

f₀ = 1 / (2π√(LC))

Series vs Parallel Resonance

Aspect Series resonance Parallel resonance
Impedance at f₀ Minimum (Z = R) Maximum (Z = L/(CR) for a practical coil)
Current at f₀ Maximum Minimum (line current)
Magnification Voltage magnification across L and C Current magnification in L and C branches
Called Acceptor circuit Rejector circuit
Power factor at f₀ Unity Unity
Uses Tuning circuits, filters Tank circuits, oscillators, wave traps

Quality Factor and Bandwidth (Series)

  • Q = X_L / R = (1/R)·√(L/C)

  • Bandwidth BW = f₀ / Q = R / (2πL)

  • Voltage across L or C at resonance = Q × supply voltage

Worked Example

Answer: f₀ ≈ 503 Hz, I = 23 A, and about 727 V appears across the inductor. A series circuit has R = 10 Ω, L = 10 mH, C = 10 µF, supplied with 230 V.

  1. f₀ = 1 / (2π√(0.01 × 10 × 10⁻⁶)) = 1 / (2π × 3.162 × 10⁻⁴) ≈ 503.3 Hz

  2. At resonance Z = R = 10 Ω → I = 230 / 10 = 23 A

  3. X_L = 2π × 503.3 × 0.01 ≈ 31.62 Ω → V_L = 23 × 31.62 ≈ 727 V

  4. Q = 31.62 / 10 ≈ 3.16 → bandwidth = 503.3 / 3.16 ≈ 159 Hz

The voltage across L and C (727 V) is much higher than the 230 V supply, a key hazard in resonant circuits.

Applications

  • Radio and TV tuners: select one station’s frequency.

  • Filters: band-pass and band-stop filters.

  • Oscillators: LC tank circuits.

  • Induction heating and wireless power transfer.

  • Power systems: harmonic filters are tuned to specific harmonics (e.g. 5th at 250 Hz).

Risks in Power Systems

Unintended resonance between power factor correction capacitors and system inductance can amplify harmonics, causing capacitor failures and overvoltage. Detuned reactors (e.g. 7% series reactors, tuned near 189 Hz on 50 Hz systems) shift the resonance below the 5th harmonic.

12

What is impedance in AC circuits?

Impedance (Z) is the total opposition an AC circuit offers to current flow, measured in ohms (Ω). It combines resistance ®, which dissipates energy, and reactance (X), which stores and returns energy in inductors and capacitors. It is a complex quantity: Z = R + jX, with magnitude |Z| = √(R² + X²) and phase angle φ = tan⁻¹(X/R).

Read full answer

Applies toElectrical engineering (AC circuit theory)

Components of Impedance

Element Opposition Formula Phase of current vs voltage
Resistor Resistance R R In phase
Inductor Inductive reactance X_L 2πfL Current lags by 90°
Capacitor Capacitive reactance X_C 1 / (2πfC) Current leads by 90°

Series RLC: Z = R + j(X_L − X_C), |Z| = √(R² + (X_L − X_C)²).

Ohm’s law for AC: V = I × Z.

Worked Example

Answer: |Z| = 50 Ω, I = 4.6 A, PF = 0.6 lagging. A coil with R = 30 Ω and L = 0.1273 H is connected to 230 V, 50 Hz.

  1. X_L = 2π × 50 × 0.1273 ≈ 40 Ω

  2. |Z| = √(30² + 40²) = 50 Ω

  3. I = 230 / 50 = 4.6 A

  4. φ = tan⁻¹(40/30) ≈ 53.13° → PF = cos φ = 30/50 = 0.6 lagging

  5. P = I²R = 4.6² × 30 ≈ 634.8 W; Q = I²X_L = 846.4 VAR; S = 1,058 VA

Adding a Capacitor

Adding a series capacitor with X_C = 40 Ω (C = 1 / (2π × 50 × 40) ≈ 79.6 µF) cancels X_L, so Z = 30 Ω and I = 7.67 A at unity PF (series resonance).

Frequency Dependence

  • X_L rises with frequency (inductors block high frequencies).

  • X_C falls with frequency (capacitors pass high frequencies).

  • This is the basis of filters: an RC low-pass filter, for example, has a cut-off at f_c = 1/(2πRC).

Admittance

Admittance Y = 1/Z = G + jB (siemens), useful for parallel circuits, where admittances add directly.

Where Impedance Matters

  • Sizing cables and protection: fault current depends on source and cable impedance.

  • Transformer percentage impedance (e.g. 5%) sets short-circuit current.

  • Audio systems (speaker impedance 4 Ω or 8 Ω).

  • Transmission lines (characteristic impedance, surge impedance loading).

  • Impedance matching in RF circuits for maximum power transfer.

13

What is Thevenin's theorem?

Thevenin’s theorem states that any linear two-terminal circuit containing sources and resistances (impedances) can be replaced, as seen from those two terminals, by a single voltage source V_th in series with a single resistance R_th. V_th is the open-circuit voltage at the terminals, and R_th is the resistance seen from the terminals with all independent sources turned off.

Read full answer

Applies toElectrical engineering (network theorems)

Steps to Find the Thevenin Equivalent

  1. Remove the load connected to the terminals A and B.

  2. Find V_th: the open-circuit voltage between A and B.

  3. Find R_th: turn off independent sources (voltage sources → short circuits, current sources → open circuits) and calculate the resistance seen from A and B. With dependent sources, use a test source or V_th / I_sc.

  4. Reconnect the load to the equivalent circuit: I_L = V_th / (R_th + R_L).

Worked Example

Answer: V_th = 7.2 V, R_th = 5 Ω, and a 5 Ω load draws 0.72 A. A 12 V source feeds R₁ = 4 Ω in series, then R₂ = 6 Ω to ground; from the junction of R₁ and R₂, a series resistor R₃ = 2.6 Ω leads to terminal A (terminal B is ground).

  1. V_th: no current flows in R₃ with the load removed, so V_th = voltage across R₂ = 12 × 6 / (4 + 6) = 7.2 V

  2. R_th: short the 12 V source → R₁ ∥ R₂ = (4 × 6) / 10 = 2.4 Ω, plus R₃ = 2.6 Ω → R_th = 5.0 Ω

  3. Load current for R_L = 5 Ω: I_L = 7.2 / (5 + 5) = 0.72 A

  4. For R_L = 10 Ω: I_L = 7.2 / 15 = 0.48 A, with no need to re-solve the whole circuit.

Why It Is Useful

  • Quickly analyse a circuit for many different loads.

  • Simplify complex networks into one source and one resistance.

  • Find the condition for maximum power transfer (R_L = R_th).

  • Model real sources: a battery is a Thevenin source (EMF plus internal resistance).

  • Power systems: the grid at a bus is represented by a Thevenin voltage and source impedance for fault calculations.

Limitations

  • Valid only for linear circuits (resistors, linear sources, linear dependent sources).

  • Gives the behaviour at the terminals only, not the internal power dissipation of the original circuit.

  • For AC circuits, use impedances and phasors (V_th and Z_th).

Relation to Norton

The Norton equivalent uses a current source I_N = V_th / R_th in parallel with R_N = R_th. The two are interchangeable (source transformation).

14

What is Norton's theorem?

Norton’s theorem states that any linear two-terminal circuit can be replaced, as seen from its terminals, by a single current source I_N in parallel with a single resistance R_N. I_N is the current that flows when the terminals are short-circuited, and R_N is the resistance seen from the terminals with all independent sources turned off (the same as the Thevenin resistance).

Read full answer

Applies toElectrical engineering (network theorems)

Steps

  1. Remove the load and short-circuit terminals A and B.

  2. Find I_N: the current through the short circuit.

  3. Find R_N: turn off independent sources (voltage sources shorted, current sources opened) and find the resistance seen from A and B.

  4. Reconnect the load in parallel with R_N: I_L = I_N × R_N / (R_N + R_L) (current divider).

Worked Example

Answer: I_N = 1.44 A, R_N = 5 Ω, and a 5 Ω load draws 0.72 A. Use the same circuit as for Thevenin: 12 V source, R₁ = 4 Ω in series, R₂ = 6 Ω to ground, and R₃ = 2.6 Ω from the junction to terminal A.

  1. Short A–B: R₃ (2.6 Ω) is now in parallel with R₂ (6 Ω): 6 ∥ 2.6 = (6 × 2.6) / 8.6 ≈ 1.814 Ω

  2. Total resistance seen by the source = 4 + 1.814 = 5.814 Ω → source current = 12 / 5.814 ≈ 2.064 A

  3. Current through R₃ (the short circuit) = 2.064 × 6 / (6 + 2.6) ≈ 1.44 A = I_N

  4. R_N = (4 ∥ 6) + 2.6 = 2.4 + 2.6 = 5.0 Ω

  5. With R_L = 5 Ω: I_L = 1.44 × 5 / (5 + 5) = 0.72 A, matching the Thevenin result.

Thevenin–Norton Conversion

From To
Thevenin (V_th, R_th) Norton: I_N = V_th / R_th, R_N = R_th
Norton (I_N, R_N) Thevenin: V_th = I_N × R_N, R_th = R_N

Here: V_th = 1.44 × 5 = 7.2 V ✓.

When Norton Is More Convenient

  • Circuits with parallel loads (currents add easily).

  • Circuits with current sources.

  • Transistor and op-amp small-signal models (output stages modelled as current sources with output resistance).

  • Nodal analysis.

Limitations

Like Thevenin’s theorem, it applies only to linear circuits and describes behaviour at the terminals only. For AC, use phasor current I_N and impedance Z_N.

15

What is the superposition theorem?

The superposition theorem states that in a linear circuit with more than one independent source, the current through (or voltage across) any element equals the algebraic sum of the currents (or voltages) produced by each source acting alone, with all other independent sources turned off. Voltage sources are replaced by short circuits and current sources by open circuits (keeping their internal resistances).

Read full answer

Applies toElectrical engineering (network theorems)

Steps

  1. Keep one independent source; turn off the others (short voltage sources, open current sources).

  2. Find the required current or voltage due to that source.

  3. Repeat for each source.

  4. Add the individual results algebraically, taking direction into account.

Dependent sources are never turned off; they remain in the circuit for each step.

Worked Example

Answer: about 1.11 A through the 6 Ω resistor. Source V₁ = 10 V connects through R₁ = 2 Ω to node X. Source V₂ = 5 V connects through R₂ = 3 Ω to the same node X. R₃ = 6 Ω connects node X to ground (both sources are referenced to ground).

V₁ alone (V₂ shorted): - R₂ ∥ R₃ = (3 × 6) / 9 = 2 Ω - V_X = 10 × 2 / (2 + 2) = 5 V → I₃‘ = 5 / 6 ≈ 0.833 A

V₂ alone (V₁ shorted): - R₁ ∥ R₃ = (2 × 6) / 8 = 1.5 Ω - V_X = 5 × 1.5 / (3 + 1.5) ≈ 1.667 V → I₃” = 1.667 / 6 ≈ 0.278 A

Total: I₃ = 0.833 + 0.278 ≈ 1.111 A (both in the same direction, towards ground)

Check by nodal analysis: V_X = (10/2 + 5/3) / (1/2 + 1/3 + 1/6) = (5 + 1.667) / 1 = 6.667 V → I₃ = 6.667 / 6 = 1.111 A ✓

Important Limitation: Power

Superposition does not apply to power directly, because power depends on the square of current. In the example, P = 1.111² × 6 ≈ 7.41 W, whereas adding individual powers gives 0.833² × 6 + 0.278² × 6 ≈ 4.17 + 0.46 = 4.63 W, which is wrong.

Conditions

  • Circuit must be linear and bilateral.

  • Not valid for non-linear elements (diodes, saturated transformers).

Applications

  • Analysing circuits with multiple sources (e.g. DC bias plus AC signal in amplifiers: DC and AC analysis are done separately).

  • Harmonic analysis in power systems: each harmonic is analysed separately and results combined.

  • Circuits with sources at different frequencies (superposition is the only correct approach, since phasors at different frequencies cannot be added directly).

16

What is the maximum power transfer theorem?

The maximum power transfer theorem states that a linear source delivers maximum power to a load when the load resistance equals the source’s Thevenin resistance: R_L = R_th. The maximum power is then P_max = V_th² / (4·R_th), and the efficiency at this point is only 50%, because the same power is lost in the source resistance.

Read full answer

Applies toElectrical engineering (network theorems)

Derivation (Brief)

Load power: P_L = I²·R_L = V_th²·R_L / (R_th + R_L)²

Setting dP_L / dR_L = 0 gives R_L = R_th. Substituting:

P_max = V_th² × R_th / (2R_th)² = V_th² / (4R_th)

Worked Example

Answer: R_L = 5 Ω for maximum power, which is about 2.59 W. Use the Thevenin equivalent V_th = 7.2 V, R_th = 5 Ω.

  • R_L = R_th = 5 Ω

  • P_max = 7.2² / (4 × 5) = 51.84 / 20 ≈ 2.59 W

Power for other loads:

R_L (Ω) Current (A) Load power (W)
2.5 0.96 2.30
5 0.72 2.59
10 0.48 2.30
20 0.288 1.66

Power falls on either side of R_L = R_th.

AC Circuits

For AC sources with impedance Z_th = R_th + jX_th, maximum power is transferred when the load is the complex conjugate: Z_L = R_th − jX_th. If only resistance can be varied, R_L = |Z_th|.

Efficiency Trade-Off

Efficiency η = R_L / (R_th + R_L)

  • At maximum power transfer: η = 50%.

  • Power systems are therefore never operated at maximum power transfer: utilities want high efficiency (95%+), so load impedances are much larger than source impedances.

Where It Is Used

  • Communication and electronics: antennas, RF amplifiers, audio amplifiers and speakers, where signal power is small and maximum transfer matters more than efficiency (impedance matching, e.g. 50 Ω RF systems).

  • Solar PV: maximum power point tracking (MPPT) adjusts the effective load so the panel operates at its maximum power point (a related but non-linear case).

  • Sensors: matching to get maximum signal.

Where It Is Not Used

Power transmission and distribution, where efficiency is the priority.

Interview Tip

State R_L = R_th, P_max = V²/(4R), and that efficiency is only 50%, so it is used in electronics and communications, not power systems.

17

What is the difference between series and parallel circuits?

In a series circuit, components are connected end to end in a single path, so the same current flows through all of them and the supply voltage is divided among them. In a parallel circuit, components are connected across the same two points, so each has the same voltage, and the total current divides among the branches.

Read full answer

Applies toElectrical engineering (circuit fundamentals)

Comparison

Aspect Series Parallel
Current Same through all components Divides among branches (I = I₁ + I₂ + …)
Voltage Divides (V = V₁ + V₂ + …) Same across all branches
Total resistance R = R₁ + R₂ + … (greater than the largest) 1/R = 1/R₁ + 1/R₂ + … (less than the smallest)
Effect of one open component Whole circuit stops Other branches keep working
Adding more components Total resistance rises, current falls Total resistance falls, total current rises
Capacitors 1/C = 1/C₁ + 1/C₂ + … C = C₁ + C₂ + …
Inductors (no coupling) L = L₁ + L₂ + … 1/L = 1/L₁ + 1/L₂ + …
Typical use Decorative lights, current-limiting resistors, fuses in series with loads House wiring, lighting circuits, battery banks for capacity

Worked Example

Answer: series 60 Ω and 0.2 A; parallel about 5.45 Ω and 2.2 A. Three resistors of 10 Ω, 20 Ω and 30 Ω are connected to a 12 V supply.

Series: - R = 10 + 20 + 30 = 60 Ω - I = 12 / 60 = 0.2 A - Voltage drops: 2 V, 4 V, 6 V (sum 12 V ✓) - Power = 12 × 0.2 = 2.4 W

Parallel: - 1/R = 1/10 + 1/20 + 1/30 = 0.1 + 0.05 + 0.0333 = 0.1833 → R ≈ 5.45 Ω - Branch currents: 1.2 A, 0.6 A, 0.4 A → total = 2.2 A - Power = 12 × 2.2 = 26.4 W

Why Homes Use Parallel Wiring

  • Every appliance gets the full 230 V.

  • Each appliance can be switched independently.

  • A failed appliance does not cut off the others.

  • But adding loads increases the total current, so each circuit is protected by an MCB sized for its cable (e.g. 6–10 A for lighting, 16–20 A for power circuits, depending on cable size and design).

Batteries

  • Series: voltages add (e.g. four 12 V batteries → 48 V), capacity (Ah) stays the same.

  • Parallel: capacity adds, voltage stays the same.

  • Combinations (e.g. 2S2P) are common in UPS, solar and EV battery packs.

18

What is a transformer, and how does it work?

A transformer is a static electrical machine that transfers AC power from one circuit to another through magnetic coupling, usually changing the voltage level (stepping up or down) while keeping the frequency the same. It works on Faraday’s law of electromagnetic induction: an alternating current in the primary winding creates an alternating magnetic flux in the core, which induces a voltage in the secondary winding.

Read full answer

Applies toElectrical engineering (electrical machines)

Construction

  • Core: laminated silicon steel (CRGO) sheets, about 0.23–0.35 mm thick, to reduce eddy current losses; core type or shell type.

  • Windings: primary and secondary coils of copper or aluminium, insulated from each other and the core.

  • Insulation and cooling: transformer oil, paper; cooling by ONAN, ONAF, OFAF methods; dry-type transformers use air and resin.

  • Accessories (power transformers): conservator, breather (silica gel), Buchholz relay, tap changer, bushings, temperature indicators, explosion vent/pressure relief device.

Working Principle

  1. AC voltage applied to the primary drives a magnetising current.

  2. This creates an alternating flux Φ in the core.

  3. The changing flux links the secondary winding and induces EMF: e = −N·dΦ/dt.

  4. When a load is connected, secondary current flows; the primary current increases correspondingly to maintain the flux (ampere-turn balance).

EMF Equation

E = 4.44 · f · N · Φ_m (volts)

where Φ_m = B_m × A (Wb), f = frequency (Hz), N = number of turns.

Worked Example

Answer: about 87 turns on the primary. A 230 V, 50 Hz transformer has a core cross-section of 0.01 m² and a maximum flux density of 1.2 T.

  1. Φ_m = 1.2 × 0.01 = 0.012 Wb

  2. N₁ = E / (4.44 × f × Φ_m) = 230 / (4.44 × 50 × 0.012) = 230 / 2.664 ≈ 86.3 → 87 turns

  3. For a 23 V secondary: N₂ ≈ 87 × 23 / 230 ≈ 8.7 → about 9 turns

Types of Transformers

Basis Types
Function Step-up, step-down, isolation
Use Power, distribution, instrument (CT, PT), auto, pulse, audio
Phases Single-phase, three-phase
Core Core type, shell type, toroidal
Cooling Oil-immersed, dry-type

Ideal Transformer Relations

V₁ / V₂ = N₁ / N₂ = I₂ / I₁, and V₁·I₁ = V₂·I₂ (no losses).

Applications

Generating station step-up transformers, grid substations, distribution transformers (11 kV/433 V), chargers and adapters, welding sets, and instrument transformers for metering and protection.

19

Why does a transformer work only on AC?

A transformer works only on AC because it needs a changing magnetic flux to induce voltage in the secondary winding (Faraday’s law: e = −N·dΦ/dt). DC produces a constant flux, so after the initial switch-on transient no voltage is induced in the secondary. Worse, with DC the primary current is limited only by the small winding resistance, so a huge current flows and burns out the winding.

Read full answer

Applies toElectrical engineering (electrical machines)

Why No Output With DC

  • With AC, the flux reverses 100 times per second (at 50 Hz), so dΦ/dt is continuously non-zero, and EMF is induced.

  • With DC, current reaches a steady value; Φ becomes constant; dΦ/dt = 0; induced EMF = 0.

  • A brief pulse appears in the secondary only at switch-on and switch-off.

Why the Transformer Burns on DC

On AC, primary current is limited mainly by the back EMF induced by the changing flux (equivalently, by the high magnetising reactance X_m). On DC there is no back EMF and no reactance, so:

I = V / R_winding

Worked Example

Answer: about 460 A on DC, versus about 1 A of no-load current on AC. A 230 V transformer has a primary winding resistance of 0.5 Ω and a no-load current of about 1 A on 230 V AC.

  • On 230 V DC: I = 230 / 0.5 = 460 A

  • Copper loss = I²R = 460² × 0.5 ≈ 105.8 kW in a small winding → overheating and insulation failure within seconds (unless a fuse or breaker trips).

  • The core also saturates heavily under DC magnetisation.

Related Effects

  • DC offset in AC: even a small DC component (e.g. from geomagnetically induced currents in power grids or half-wave rectifier loads) can push the core into saturation, causing overheating, noise and harmonics.

  • Pulse transformers in SMPS work with pulsed (changing) DC, which still provides a changing flux; they need core reset each cycle.

  • DC-DC converters therefore chop DC into high-frequency AC, pass it through a small transformer, then rectify it again.

Interview Tip

Answer in two parts: (1) no changing flux, so no induced EMF; (2) no back EMF, so excessive current through the low winding resistance, which burns the winding. Interviewers expect both points.

20

What is the turns ratio of a transformer?

The turns ratio of a transformer is the ratio of the number of turns on the primary winding to the number on the secondary winding: a = N₁ / N₂. For an ideal transformer, it equals the voltage ratio and the inverse of the current ratio: N₁ / N₂ = V₁ / V₂ = I₂ / I₁. It decides whether the transformer steps voltage up (a < 1) or down (a > 1).

Read full answer

Applies toElectrical engineering (electrical machines)

Relations

  • Voltage: V₂ = V₁ × N₂ / N₁

  • Current: I₂ = I₁ × N₁ / N₂

  • Power (ideal): V₁·I₁ = V₂·I₂

  • Impedance referred to the primary: Z₁‘ = (N₁ / N₂)² × Z₂ = a²·Z₂

Worked Example 1: Distribution Transformer

Answer: turns ratio ≈ 25.4; currents ≈ 13.1 A (HV) and 333 A (LV). A 250 kVA, 11 kV/433 V three-phase transformer.

  • Ratio = 11,000 / 433 ≈ 25.4 (step-down)

  • HV line current = 250,000 / (√3 × 11,000) ≈ 13.1 A

  • LV line current = 250,000 / (√3 × 433) ≈ 333.3 A

  • Check: 333.3 / 13.1 ≈ 25.4 ✓

(For a delta-star transformer the per-phase turns ratio differs from the line voltage ratio by √3, because the HV winding sees line voltage and the LV winding sees phase voltage: N₁/N₂ = 11,000 / (433/√3) ≈ 44.)

Worked Example 2: Reflected Impedance

A 10:1 audio transformer with an 8 Ω speaker on the secondary appears to the amplifier as Z₁ = 10² × 8 = 800 Ω.

Uses of Turns Ratio

  • Selecting step-up or step-down transformers.

  • Tap changers alter the effective turns ratio to regulate output voltage (e.g. ±5% to ±10% in 2.5% steps on distribution transformers; on-load tap changers on power transformers).

  • Ratio test: measuring the turns ratio (with a TTR meter) checks for shorted turns and correct tap connections during commissioning and maintenance.

  • Impedance matching in audio and RF circuits.

  • Current transformers: a 100/5 A CT has a turns ratio of 1:20 (one primary turn, 20 secondary turns).

Real Transformers

Under load, the secondary voltage falls slightly because of winding resistance and leakage reactance; this is described by voltage regulation, typically a few percent for distribution transformers. Nameplate voltage ratios are given at no load.

21

What are the losses in a transformer?

A transformer has two main groups of losses: core (iron) losses, made up of hysteresis and eddy current losses, which depend on voltage and frequency and stay almost constant whatever the load; and copper (I²R) losses in the windings, which vary with the square of the load current. Smaller losses include stray losses and dielectric losses. Because there are no moving parts, there are no mechanical losses.

Read full answer

Applies toElectrical engineering (electrical machines)

Types of Losses

Loss Cause Depends on Reduced by
Hysteresis loss Repeated magnetisation reversal of the core f, B_m^1.6 (Steinmetz) High-grade silicon steel (CRGO), amorphous cores
Eddy current loss Circulating currents induced in the core f², B_m², lamination thickness² Thin insulated laminations (0.23–0.35 mm)
Copper loss I²R heating in windings Load current squared Larger conductors, lower current density
Stray loss Leakage flux inducing currents in tank and clamps Load Magnetic shielding, design
Dielectric loss Insulation (oil, paper) Voltage Good insulation quality

Formulas

  • Hysteresis: P_h = η·B_m^1.6·f·V (Steinmetz)

  • Eddy current: P_e = K_e·B_m²·f²·t²·V

  • Copper loss at load fraction x: P_cu = x²·P_cu(full load)

Worked Example

Answer: total losses = 875 W at half load and 2,000 W at full load. A 100 kVA transformer has iron loss 500 W and full-load copper loss 1,500 W.

Load Iron loss (W) Copper loss (W) Total (W)
Full load (x = 1) 500 1,500 2,000
Half load (x = 0.5) 500 0.5² × 1,500 = 375 875
No load 500 ≈ 0 500

How Losses Are Measured

  • Open-circuit (no-load) test: gives core loss.

  • Short-circuit test: gives full-load copper loss.

Why Losses Matter

  • Losses become heat, limiting the transformer’s rating and requiring cooling (oil, radiators, fans).

  • They reduce efficiency and cost money over the transformer’s life (often 25–30 years).

  • Distribution transformers are energised all the time, so core loss runs 24 hours a day. India’s BEE star-labelling and IS 1180 set maximum loss limits for distribution transformers.

22

What are the open-circuit and short-circuit tests of a transformer?

The open-circuit (no-load) test and the short-circuit test find a transformer’s losses and equivalent-circuit parameters without loading it fully. The open-circuit test, done at rated voltage with the other winding open, gives the core (iron) loss and the magnetising branch. The short-circuit test, done at rated current with the other winding shorted, gives the full-load copper loss and the series impedance. Together they let you calculate efficiency and voltage regulation at any load.

Read full answer

Applies toElectrical engineering (electrical machines and testing)

Open-Circuit Test

  • Setup: instruments (voltmeter, ammeter, wattmeter) on the LV side; HV side open.

  • Applied: rated voltage at rated frequency.

  • Measured: V₀, I₀ (small, about 2–5% of rated current), W₀.

  • Result: W₀ ≈ core loss (copper loss is negligible because I₀ is small).

Calculations: - cos φ₀ = W₀ / (V₀·I₀) - I_w = I₀·cos φ₀ (core loss component); I_µ = I₀·sin φ₀ (magnetising component) - R₀ = V₀ / I_w; X₀ = V₀ / I_µ

Short-Circuit Test

  • Setup: instruments on the HV side; LV side shorted.

  • Applied: a low voltage (about 5–10% of rated) raised until rated current flows.

  • Measured: V_sc, I_sc, W_sc.

  • Result: W_sc ≈ full-load copper loss (core loss is negligible at this low voltage).

Calculations: - Z_eq = V_sc / I_sc; R_eq = W_sc / I_sc²; X_eq = √(Z_eq² − R_eq²) - Percentage impedance = V_sc / V_rated × 100

Worked Example: Open-Circuit Test

Answer: core loss = 50 W, R₀ ≈ 1,058 Ω, X₀ ≈ 236 Ω. OC test on the 230 V side: 230 V, 1.0 A, 50 W.

  1. cos φ₀ = 50 / (230 × 1.0) ≈ 0.2174; sin φ₀ ≈ 0.976

  2. I_w = 0.2174 A → R₀ = 230 / 0.2174 ≈ 1,058 Ω

  3. I_µ = 0.976 A → X₀ = 230 / 0.976 ≈ 235.7 Ω

Worked Example: Short-Circuit Test

Answer: Z ≈ 17.25 Ω, R ≈ 6.35 Ω, X ≈ 16.04 Ω, and impedance ≈ 3.26%. A 10 kVA, 2,300/230 V transformer: SC test on the HV side gives 75 V, 4.348 A (rated), 120 W.

  1. Z_eq = 75 / 4.348 ≈ 17.25 Ω

  2. R_eq = 120 / 4.348² = 120 / 18.90 ≈ 6.35 Ω

  3. X_eq = √(17.25² − 6.35²) = √(297.6 − 40.3) ≈ 16.04 Ω

  4. %Z = 75 / 2,300 × 100 ≈ 3.26%

Why These Tests Are Useful

  • Only a small amount of power is needed (no need to load the transformer fully).

  • They give losses for efficiency calculations and parameters for voltage regulation.

  • Percentage impedance sets fault current and is needed for parallel operation.

23

Why is a transformer rated in kVA and not kW?

A transformer is rated in kVA because its losses, and therefore its heating, depend on voltage (core loss) and current (copper loss), not on the load’s power factor. The manufacturer does not know what power factor the user’s load will have, so the rating states the voltage and current it can safely carry, which is apparent power (kVA). The real power (kW) delivered depends on the load: kW = kVA × power factor.

Read full answer

Applies toElectrical engineering (electrical machines)

Reasoning

  • Core loss depends on applied voltage and frequency.

  • Copper loss depends on current (I²R).

  • Neither depends on the phase angle between voltage and current.

  • Temperature rise, which limits the rating, is caused by these losses.

  • So the limit is V × I (kVA), independent of PF.

Worked Example

Answer: the same current of about 139 A flows in each case, but the kW delivered ranges from 50 kW to 100 kW. A 100 kVA, 415 V three-phase transformer at full load:

  • Rated current = 100,000 / (√3 × 415) ≈ 139.1 A

Load PF kW delivered Current (A) Copper loss
1.0 100 139.1 Full-load value
0.8 80 139.1 Same
0.5 50 139.1 Same

The transformer heats up the same amount whether it delivers 100 kW or 50 kW, so it cannot be rated in kW.

What Is Rated in kW?

  • Motors are rated in kW (or HP) because they deliver mechanical output power, which is fixed by design.

  • Alternators and generators are rated in kVA (they also supply loads of unknown PF), with a rated PF (often 0.8) for the prime mover’s kW limit.

  • UPS and inverters are often given both kVA and kW ratings.

Practical Implication

When sizing a transformer, estimate the load kW and divide by the expected PF (with margin): a 160 kW load at PF 0.8 needs at least 200 kVA, so a 250 kVA unit is chosen to allow for growth and to run near maximum efficiency.

Interview Tip

The one-line answer: “Losses depend on voltage and current, not power factor, so the rating is in kVA.” Then mention that motors are rated in kW because they deliver mechanical power.

24

What is transformer efficiency, and when is it maximum?

Transformer efficiency is the ratio of output power to input power: η = output / (output + losses) × 100%. Large transformers are very efficient, often 97–99.5%. Efficiency is maximum when the copper loss equals the core (iron) loss, which happens at the load fraction x = √(P_i / P_cu,FL).

Read full answer

Applies toElectrical engineering (electrical machines)

Efficiency Formula

At load fraction x (of full-load kVA) and power factor cos φ:

η = (x·S·cos φ) / (x·S·cos φ + P_i + x²·P_cu)

  • S = rated kVA, P_i = iron loss, P_cu = full-load copper loss.

Condition for Maximum Efficiency

Differentiating η with respect to current and setting it to zero gives variable loss = constant loss, i.e. x²·P_cu = P_i.

Worked Example

Answer: full-load efficiency ≈ 97.56%; maximum ≈ 97.88% at about 57.7 kVA. A 100 kVA transformer has iron loss 500 W and full-load copper loss 1,500 W, supplying a load at PF 0.8.

Full load: - Output = 100 × 0.8 = 80 kW; losses = 500 + 1,500 = 2,000 W - η = 80,000 / 82,000 ≈ 97.56%

Maximum efficiency: - x = √(500 / 1,500) ≈ 0.577 → load ≈ 57.7 kVA - Output = 57.7 × 0.8 ≈ 46.19 kW; losses = 500 + 500 = 1,000 W - η_max = 46.19 / 47.19 ≈ 97.88%

All-Day (Energy) Efficiency

Distribution transformers are energised 24 hours a day but loaded variably, so all-day efficiency is used:

η_all-day = output energy (kWh) in 24 h / input energy (kWh) in 24 h

They are designed with low core loss and reach maximum efficiency at about 40–60% load, because their core loss runs all day. Power transformers in generating stations usually run near full load, so they are designed for maximum efficiency near full load.

Factors Affecting Efficiency

  • Power factor: lower PF gives lower efficiency (less kW for the same losses).

  • Load level: efficiency is low at very light load, where core loss dominates.

  • Core material: CRGO or amorphous steel reduces core loss.

  • Temperature: higher winding temperature increases resistance and copper loss.

Interview Tip

State the condition (copper loss = iron loss), give the formula for the load fraction, and mention that distribution transformers are designed for maximum efficiency at part load.

25

What is the difference between a power transformer and a distribution transformer?

A power transformer is used in generating stations and transmission substations to step voltages up or down at high levels (e.g. 11 kV to 220/400 kV, or 220 kV to 33 kV). It usually runs near full load and is designed for maximum efficiency at or near full load. A distribution transformer steps down the distribution voltage (e.g. 11 kV or 33 kV) to the utilisation voltage (433/250 V) for consumers. It runs at varying load around the clock and is designed for low core loss and good all-day efficiency.

Read full answer

Applies toElectrical engineering (power systems and electrical machines)

Comparison

Aspect Power transformer Distribution transformer
Location Generating stations, transmission substations Near consumers (pole-mounted or plinth-mounted)
Typical rating Several MVA to hundreds of MVA About 10 kVA to 2,500 kVA
Voltage levels 11 kV ↔ 66/132/220/400/765 kV 11 kV or 33 kV → 433 V
Loading Near full load most of the time Variable, often 30–60% average
Designed for Maximum efficiency near full load Maximum efficiency at about 40–60% load; low core loss
Efficiency measure Ordinary (power) efficiency All-day (energy) efficiency
Size Large Small to medium
Tap changer Often on-load (OLTC) Usually off-circuit taps (OLTC on some newer units)
Protection Differential, Buchholz, REF, OTI/WTI, overcurrent Fuses (HG/DO), LT breakers, Buchholz on larger units
Typical vector group YNd1, Dyn11, YNyn0 (depending on application) Dyn11 (gives neutral for single-phase loads)
Cost focus Reliability and efficiency at full load Low losses at part load, cost

Worked Example: Selecting a Distribution Transformer

Answer: choose a 250 kVA transformer. A residential colony has a maximum demand of 180 kW at PF 0.9.

  • Required kVA = 180 / 0.9 = 200 kVA

  • Standard ratings: 100, 160, 200, 250, 315, 400, 500, 630 kVA

  • A 200 kVA unit would run at 100% at peak with no margin, so 250 kVA is chosen (about 80% loading at peak, allowing for growth).

Maintenance

Both need regular oil testing (BDV, moisture, dissolved gas analysis for power transformers), checks on silica gel breathers, bushings and earthing, and thermal scans.

26

What is an autotransformer?

An autotransformer is a transformer with a single winding that acts as both primary and secondary: part of the winding is common to both circuits. Part of the power is transferred by direct electrical conduction and part by induction. It is smaller, cheaper and more efficient than a two-winding transformer for small voltage ratios, but it gives no electrical isolation between input and output.

Read full answer

Applies toElectrical engineering (electrical machines)

Working

  • The full winding is connected across the input.

  • The output is taken from a tap on the winding (for a step-down unit).

  • The common section carries only the difference between the input and output currents.

Copper Saving

For a voltage ratio K = V_LV / V_HV (K < 1):

Copper in autotransformer = (1 − K) × copper in an equivalent two-winding transformer

Saving = K × copper of the two-winding transformer. The saving is large when K is close to 1.

Worked Example

Answer: about 87% copper saving; the common winding carries only about 3.3 A. A 230 V / 200 V autotransformer supplies a 5 kVA load.

  1. K = 200 / 230 ≈ 0.870 → copper saving ≈ 87%

  2. Output current I₂ = 5,000 / 200 = 25 A; input current I₁ = 5,000 / 230 ≈ 21.74 A

  3. Current in the common section = 25 − 21.74 ≈ 3.26 A

  4. Power transferred by induction = (1 − K) × 5 kVA ≈ 0.65 kVA; by conduction = K × 5 ≈ 4.35 kVA

Advantages

  • Less copper and core material, so lower cost and smaller size.

  • Lower losses and higher efficiency.

  • Better voltage regulation (lower leakage reactance).

  • Smooth variable output (variac).

Disadvantages

  • No isolation: a break in the common winding can put the full input voltage on the output, which is dangerous for equipment and people.

  • Higher short-circuit current (lower impedance).

  • Economical mainly for ratios near 1 (typically up to about 2:1 or 3:1).

Applications

  • Variac (variable autotransformer) in labs.

  • Autotransformer starters for induction motors (reduced-voltage starting, taps such as 50%, 65%, 80%).

  • Interconnecting transformers (ICTs) between 400 kV and 220 kV grids.

  • Voltage stabilisers and boosters (servo stabilisers).

  • Railway traction supply (2 × 25 kV systems).

27

What is the working principle of a DC motor?

A DC motor works on the principle that a current-carrying conductor placed in a magnetic field experiences a mechanical force. The force is F = B·I·L, and its direction follows Fleming’s left-hand rule. In a DC motor, armature conductors carrying current sit in the field of the poles; the forces on them create a torque that turns the rotor, and the commutator reverses the current in each conductor as it passes from one pole to the next, so the torque always acts in the same direction.

Read full answer

Applies toElectrical engineering (DC machines)

Main Parts

Part Function
Yoke Outer frame; carries magnetic flux and supports poles
Field poles and windings (or permanent magnets) Produce the main magnetic field
Armature core and winding Laminated rotor carrying current-carrying conductors
Commutator Segmented copper ring that reverses current in armature coils
Brushes (carbon) Carry current to the rotating commutator
Shaft and bearings Transmit mechanical power

Fleming’s Left-Hand Rule

Stretch the thumb, first finger and second finger of the left hand at right angles: First finger = Field (N to S), seCond finger = Current, thuMb = Motion (force).

Torque Equation

T = (P·Φ·Z·I_a) / (2π·A) = 0.159 × (P·Φ·Z·I_a / A) N·m

  • P = poles, Φ = flux per pole (Wb), Z = total armature conductors, I_a = armature current, A = parallel paths.

  • For a given machine: T ∝ Φ·I_a.

Worked Example

Answer: about 76 N·m. A 4-pole, lap-wound DC motor (A = 4) has 480 conductors, flux per pole 0.025 Wb and armature current 40 A.

T = (4 × 0.025 × 480 × 40) / (2π × 4) = 1,920 / 25.13 ≈ 76.4 N·m

Single-conductor check: a conductor 0.3 m long carrying 20 A in a 0.8 T field experiences F = 0.8 × 20 × 0.3 = 4.8 N.

Why the Commutator Is Needed

Without it, the current in a conductor would keep the same direction as it moved from the N pole to the S pole, so the torque would reverse every half turn and the rotor would just oscillate. The commutator switches the coil connections at the right moment to keep torque unidirectional.

Applications

Traction (older locomotives, e-rickshaws often use BLDC now), cranes and hoists, rolling mills, toys, automotive starters, and small PMDC motors in appliances. Modern drives increasingly use induction motors with VFDs or BLDC motors, which avoid brush and commutator maintenance.

28

What is back EMF in a DC motor?

Back EMF (counter EMF, E_b) is the voltage induced in the armature of a running DC motor, because its conductors are cutting the magnetic field, just as in a generator. By Lenz’s law it opposes the supply voltage. The armature current is set by the difference: I_a = (V − E_b) / R_a. Back EMF makes the motor self-regulating: when the load increases, speed and E_b drop slightly, so more current flows and more torque is produced.

Read full answer

Applies toElectrical engineering (DC machines)

Formulas

  • E_b = (P·Φ·Z·N) / (60·A), so E_b ∝ Φ·N

  • V = E_b + I_a·R_a (voltage equation)

  • Mechanical power developed = E_b·I_a

  • Speed: N ∝ E_b / Φ = (V − I_a·R_a) / Φ

Worked Example

Answer: E_b = 210 V and 4.2 kW of mechanical power is developed; at standstill the current would be 440 A. A 220 V DC shunt motor has armature resistance 0.5 Ω and draws an armature current of 20 A.

  1. E_b = V − I_a·R_a = 220 − 20 × 0.5 = 210 V

  2. Mechanical power developed = 210 × 20 = 4,200 W

  3. Armature copper loss = 20² × 0.5 = 200 W (input to armature = 220 × 20 = 4,400 W ✓)

At starting (N = 0, so E_b = 0): I_a = 220 / 0.5 = 440 A, 22 times the running current.

Why a Starter Is Needed

To limit starting current to, say, 1.5 times the running current (30 A): - Total resistance = 220 / 30 ≈ 7.33 Ω - External starting resistance = 7.33 − 0.5 ≈ 6.83 Ω, cut out in steps as speed (and E_b) rises.

Three-point and four-point starters do this and also provide no-volt and overload protection.

Significance of Back EMF

  • Self-regulation: load ↑ → N ↓ → E_b ↓ → I_a ↑ → torque ↑.

  • Energy conversion: E_b·I_a is the electrical power converted to mechanical power.

  • Speed control: changing V (armature voltage control) or Φ (field control) changes speed.

  • Efficiency: the ratio E_b / V is close to the armature efficiency.

Interview Tip

Point out that back EMF is zero at start, which is why DC motors need starters, and that it is what lets the motor adjust its current to the load automatically.

29

What are the types of DC motors, and where is each used?

DC motors are classified by how the field winding is connected to the armature: separately excited, self-excited shunt, series and compound motors, plus permanent magnet DC (PMDC) motors that use magnets instead of a field winding. Each type has different speed–torque characteristics, which decide where it is used.

Read full answer

Applies toElectrical engineering (DC machines)

Types and Characteristics

Type Field connection Speed–torque behaviour Typical uses
Separately excited Field supplied from an independent source Precise, wide speed control Rolling mills, paper machines, test benches, Ward-Leonard drives
Shunt Field in parallel with armature Nearly constant speed (falls about 5–15% from no load to full load); moderate starting torque Lathes, fans, blowers, centrifugal pumps, conveyors, machine tools
Series Field in series with armature Very high starting torque (T ∝ I_a² before saturation); speed falls sharply with load; dangerous at no load Traction (trains, trams), cranes, hoists, automotive starter motors
Cumulative compound Series and shunt fields aiding High starting torque with a safe no-load speed Presses, shears, rolling mills, elevators, compressors
Differential compound Series field opposes shunt Unstable at overload; rarely used Experimental use only
PMDC Permanent magnets Linear speed–torque, compact Toys, wipers, small fans, power windows, small tools

Worked Example: Shunt Motor Speed Change

Answer: speed drops from 1,000 rpm to about 952 rpm. A 220 V shunt motor (R_a = 0.5 Ω) runs at 1,000 rpm with I_a = 20 A. The load doubles, so I_a = 40 A (flux constant).

  1. E_b1 = 220 − 20 × 0.5 = 210 V

  2. E_b2 = 220 − 40 × 0.5 = 200 V

  3. N₂ = N₁ × E_b2 / E_b1 = 1,000 × 200 / 210 ≈ 952 rpm

So doubling the load changes the speed by less than 5%, which is why shunt motors are called constant-speed motors.

Choosing a DC Motor

  • Constant speed, varying load: shunt.

  • Heavy starting loads: series or cumulative compound.

  • Precise wide-range speed control: separately excited.

  • Small, simple, battery-powered: PMDC.

Modern Trend

Many DC motor applications now use induction motors with VFDs or BLDC motors, which need less maintenance (no brushes or commutator). DC motors remain in older installations, automotive and low-cost battery applications.

30

Why should a DC series motor never be started without load?

A DC series motor should never be started or run without a mechanical load because its speed rises to a dangerously high value (runaway). In a series motor the field current equals the armature current, so at no load the current is very small, the flux becomes very weak, and since speed is inversely proportional to flux (N ∝ E_b / Φ), the motor races. Centrifugal forces can then throw the armature windings out of their slots and destroy the commutator.

Read full answer

Applies toElectrical engineering (DC machines)

Explanation

  • Speed: N ∝ (V − I_a·(R_a + R_se)) / Φ

  • In a series motor, Φ ∝ I_a (below saturation).

  • At no load, I_a is very small → Φ is very small → N becomes extremely high.

Worked Example

Answer: speed would rise to about 8,700 rpm, more than ten times the normal speed. A 220 V series motor has total resistance (armature + series field) of 0.5 Ω and runs at 800 rpm when drawing 40 A. Assume flux is proportional to current. On light load it draws only 4 A.

  1. E_b1 = 220 − 40 × 0.5 = 200 V

  2. E_b2 = 220 − 4 × 0.5 = 218 V

  3. N₂ = N₁ × (E_b2 / E_b1) × (Φ₁ / Φ₂) = 800 × (218 / 200) × (40 / 4) = 800 × 1.09 × 10 ≈ 8,720 rpm

At true no load the current falls further, so the speed would climb even higher until friction and windage balance it, often at a destructive level.

Torque Characteristics

  • T ∝ Φ·I_a ∝ I_a² (before saturation), so series motors produce very high starting torque, which suits traction and cranes.

Precautions

  • Never use belt drives with series motors, because a broken or slipping belt removes the load. Use gears or direct coupling.

  • Always start and run with load connected.

  • Provide overspeed protection where needed.

  • Small series motors (e.g. in mixers and drills, universal motors) are protected by internal friction, fan and gear loads, which limit their no-load speed.

Interview Tip

Explain the chain: no load → low current → low flux → very high speed (N ∝ 1/Φ) → mechanical damage. Then add the belt-drive rule, which interviewers often ask as a follow-up.

31

What is the working principle of a three-phase induction motor?

A three-phase induction motor works on electromagnetic induction. Three-phase current in the stator winding produces a rotating magnetic field (RMF) that turns at synchronous speed. This field cuts the rotor conductors and induces EMF and current in them. By Lenz’s law, the rotor currents create a force that tries to reduce the relative motion, so the rotor turns in the same direction as the field, but always slightly slower. That speed difference (slip) is needed for induction to occur.

Read full answer

Applies toElectrical engineering (AC machines)

Construction

  • Stator: laminated core with a three-phase distributed winding, connected in star or delta.

  • Rotor: squirrel cage (bars shorted by end rings) or slip ring (wound rotor with external resistance through slip rings and brushes).

  • Air gap: small (about 0.4–1 mm) to keep magnetising current low.

Rotating Magnetic Field

Three windings displaced by 120° in space, carrying currents displaced by 120° in time, produce a field of constant magnitude (1.5 times the peak field of one phase) rotating at:

N_s = 120·f / P (rpm)

Worked Example

Answer: N_s = 1,500 rpm, rotor speed = 1,440 rpm, rotor frequency = 2 Hz. A 4-pole, 50 Hz motor runs at 4% slip.

  1. N_s = 120 × 50 / 4 = 1,500 rpm

  2. N = N_s(1 − s) = 1,500 × 0.96 = 1,440 rpm

  3. Rotor current frequency f_r = s·f = 0.04 × 50 = 2 Hz

Sequence of Operation

  1. Supply → stator currents → RMF at N_s.

  2. RMF cuts stationary rotor conductors → EMF induced (transformer action).

  3. Short-circuited rotor → rotor currents flow.

  4. Rotor currents in the field → force (F = BIL) → torque.

  5. Rotor accelerates to a speed just below N_s, where torque matches the load.

Reversing direction: Interchange any two supply phases: this reverses the phase sequence and the direction of the RMF.

Advantages

  • Simple, rugged, low cost, very little maintenance (no brushes in squirrel cage).

  • Self-starting.

  • High efficiency (IE2/IE3 classes about 85–95% depending on size).

Disadvantages

  • Speed is nearly constant on a fixed supply; speed control needs a VFD.

  • Lagging power factor, poor at light load.

  • High starting current (5–7 times full-load current on DOL).

Applications: Pumps, fans, compressors, conveyors, machine tools, lifts, and nearly all industrial drives; it is the most widely used motor in industry.

32

What is slip in an induction motor?

Slip is the difference between the synchronous speed of the rotating magnetic field and the actual rotor speed, expressed as a fraction (or percentage) of synchronous speed: s = (N_s − N) / N_s. Slip is essential, because without relative motion no EMF would be induced in the rotor and no torque would be produced. Typical full-load slip is about 2–6%, lower for large motors.

Read full answer

Applies toElectrical engineering (AC machines)

Key Relations

  • N_s = 120·f / P

  • N = N_s(1 − s)

  • Rotor frequency: f_r = s·f

  • Rotor induced EMF: E₂ₛ = s·E₂ (E₂ = standstill rotor EMF)

  • Power flow: rotor copper loss = s × air-gap power; mechanical power = (1 − s) × air-gap power

Slip at Different Conditions

Condition Slip
At start (rotor stationary) s = 1
No load Very small (about 0.5–1%)
Full load About 2–6%
At synchronous speed (theoretical) s = 0, so no torque
Generator action (rotor driven above N_s) s < 0
Plugging (braking by reversing phases) s > 1

Worked Example

Answer: s = 4%, rotor frequency 2 Hz, rotor copper loss 400 W and gross mechanical power 9.6 kW. A 6-pole, 50 Hz motor runs at 960 rpm, with 10 kW of air-gap power.

  1. N_s = 120 × 50 / 6 = 1,000 rpm

  2. s = (1,000 − 960) / 1,000 = 0.04 (4%)

  3. f_r = 0.04 × 50 = 2 Hz

  4. Rotor copper loss = 0.04 × 10 kW = 400 W

  5. Gross mechanical power = (1 − 0.04) × 10 = 9.6 kW (subtract friction and windage to get shaft output)

Measuring Slip

  • Tachometer speed and the calculated N_s.

  • Stroboscope.

  • Counting rotor current oscillations (e.g. on a moving-coil ammeter in the rotor circuit of a slip ring motor): slip frequency × 60 = slip in rpm.

Why Slip Matters

  • Torque is roughly proportional to slip in the normal operating range.

  • Rotor losses rise with slip, so high-slip operation is inefficient.

  • Slip changes with load, allowing the motor to adjust its torque.

  • Slip ring motors with external rotor resistance increase slip deliberately to raise starting torque or reduce speed (at the cost of efficiency).

33

Why is an induction motor called an asynchronous motor?

An induction motor is called an asynchronous motor because its rotor never runs at synchronous speed (the speed of the rotating magnetic field). It must always run slightly slower; if the rotor reached synchronous speed, there would be no relative motion between the field and the rotor conductors, no induced EMF, no rotor current and no torque, so the rotor would slow down again.

Read full answer

Applies toElectrical engineering (AC machines)

Explanation

  1. The stator RMF rotates at N_s = 120f/P.

  2. Torque comes from rotor currents induced by the field cutting the rotor conductors.

  3. Induction needs relative motion, i.e. N < N_s (slip s > 0).

  4. At N = N_s, slip = 0 → rotor EMF = 0 → torque = 0.

  5. Friction, windage and load always need some torque, so the rotor settles at a speed below N_s.

Worked Example

Answer: the field turns at 3,000 rpm but the rotor at about 2,880 rpm. A 2-pole, 50 Hz motor at full load has a slip of 4%.

  • N_s = 120 × 50 / 2 = 3,000 rpm

  • N = 3,000 × (1 − 0.04) = 2,880 rpm

  • The rotor “slips” back by 120 rpm, so it is out of step (asynchronous) with the field.

Nameplate speeds such as 2,880, 1,440, 960 and 720 rpm (for 2, 4, 6 and 8 poles at 50 Hz) reflect this.

Comparison With a Synchronous Motor

Aspect Induction (asynchronous) motor Synchronous motor
Speed Slightly below N_s, varies a little with load Exactly N_s at all loads
Rotor excitation Induced currents (no external supply) DC excitation or permanent magnets
Self-starting Yes No (needs damper winding, VFD or pony motor)
Power factor Always lagging Adjustable (lagging, unity or leading)
Cost and maintenance Low Higher
Typical use General industrial drives Constant-speed large drives, PF correction

Induction Generators

If the rotor is driven faster than N_s (negative slip), the machine works as an induction (asynchronous) generator, used in some wind turbines and small hydro plants. It still draws reactive power from the grid or capacitors for excitation.

Interview Tip

The key point: “Torque needs induced current, induced current needs relative motion, so the rotor can never reach synchronous speed.”

34

What is the difference between squirrel cage and slip ring induction motors?

A squirrel cage induction motor has a rotor made of copper or aluminium bars permanently short-circuited by end rings. It is simple, rugged and cheap, but rotor resistance cannot be changed externally. A slip ring (wound rotor) induction motor has a three-phase winding on the rotor connected through slip rings and brushes to external resistances, which can be added at start to give high starting torque with lower starting current, and to control speed.

Read full answer

Applies toElectrical engineering (AC machines)

Comparison

Aspect Squirrel cage Slip ring (wound rotor)
Rotor Bars shorted by end rings Three-phase winding, star-connected, brought out to slip rings
External resistance Not possible Possible through slip rings
Starting torque Low to moderate (better with double-cage or deep-bar designs) High (adjustable with rotor resistance)
Starting current High (5–7 × FLC on DOL) Lower with rotor resistance
Speed control Only by supply (VFD, pole changing) Rotor resistance control (inefficient), slip power recovery
Construction Simple, robust Complex
Maintenance Very low Brushes and slip rings need maintenance
Efficiency Higher Slightly lower
Cost Lower Higher
Sparking risk None Possible at brushes
Use share About 90% or more of induction motors Special heavy-start applications

Worked Example: Rotor Resistance for Maximum Starting Torque

Answer: add about 0.4 Ω per phase (referred to the rotor). A slip ring motor has rotor resistance R₂ = 0.1 Ω and standstill rotor reactance X₂ = 0.5 Ω per phase.

Maximum torque occurs at slip s = R₂ / X₂. For maximum torque at starting (s = 1), total rotor resistance must equal X₂:

  • Required R₂ total = 0.5 Ω

  • External resistance = 0.5 − 0.1 = 0.4 Ω per phase

Without external resistance, maximum torque occurs at s = 0.1 / 0.5 = 0.2 (i.e. near 80% of synchronous speed), and starting torque is much lower.

Applications

Squirrel cage: pumps, fans, blowers, compressors, conveyors, machine tools, general drives.

Slip ring: cranes, hoists, elevators (older), crushers, ball mills, heavy conveyors, and loads needing high starting torque with limited supply capacity.

Modern Trend

VFDs give squirrel cage motors high starting torque, low starting current and efficient speed control, so slip ring motors are now used less, mainly for very large high-inertia loads or in existing installations.

35

Why does an induction motor draw high starting current? How is it started?

An induction motor draws a high starting current (typically 5–7 times full-load current on direct-on-line starting) because at standstill the slip is 1, so the rotor behaves like the short-circuited secondary of a transformer: there is no back EMF-like effect from rotor speed, the rotor EMF is at its maximum, and only the small rotor and stator impedances limit the current. Starting methods reduce the voltage or control the supply to limit this current, protecting the supply and the motor.

Read full answer

Applies toElectrical engineering (AC machines and motor control)

Why the Current Is High

  • At start, rotor EMF E₂ is maximum (slip = 1), and rotor frequency is the supply frequency.

  • Rotor current I₂ = E₂ / √(R₂² + X₂²), limited only by small leakage impedance.

  • As the motor speeds up, slip and rotor EMF fall, and current reduces to the normal value.

Problems Caused

  • Voltage dip in the supply (lights flicker, other equipment may trip).

  • Heating of motor windings during long starts.

  • Mechanical shock to coupled machinery.

  • Utility limits on starting current for large motors.

Starting Methods

Method Starting current (vs DOL) Starting torque (vs DOL) Typical use
Direct-on-line (DOL) 100% (5–7 × FLC) 100% Small motors (often up to about 5–7.5 kW)
Star-delta 1/3 1/3 Medium motors with light starting loads
Autotransformer (tap k) k² k² Larger motors needing more torque than star-delta
Stator resistance/reactance k k² Rarely used now
Rotor resistance (slip ring) Low High Heavy-start loads
Soft starter (thyristors) Adjustable (about 2–4 × FLC) Reduced, smooth Pumps, fans, conveyors
VFD About 1–1.5 × FLC Full torque available Speed control plus soft starting

Worked Example

Answer: DOL ≈ 164 A, star-delta ≈ 55 A, 65% autotransformer ≈ 69 A. A 15 kW, 415 V motor has efficiency 90% and PF 0.85; DOL starting current is 6 times FLC.

  1. FLC = 15,000 / (1.732 × 415 × 0.85 × 0.90) ≈ 27.3 A

  2. DOL: 6 × 27.3 ≈ 164 A

  3. Star-delta: 164 / 3 ≈ 55 A (torque 1/3 of DOL)

  4. Autotransformer at 65% tap: line current = 0.65² × 164 ≈ 69 A (torque 42% of DOL)

Selection Tips

  • Check the load’s torque needs: star-delta suits pumps and fans started unloaded, not loaded conveyors.

  • Soft starters and VFDs also reduce mechanical stress and water hammer in pumps.

  • Follow the supply utility’s rules on maximum starting current for large motors.

36

What is a star-delta starter?

A star-delta starter starts a three-phase induction motor with its stator windings connected in star, so each winding gets only 1/√3 of the line voltage, then switches them to delta for normal running at full voltage. This reduces starting current and starting torque to one-third of their direct-on-line values. It is widely used for medium-sized motors (roughly 7.5–75 kW) whose windings are designed for delta operation at the supply voltage (e.g. 415 V delta).

Read full answer

Applies toElectrical engineering (motor control)

Components

  • Main contactor (supplies the line to one end of the windings).

  • Star contactor (shorts the other ends together to form star).

  • Delta contactor (connects windings in delta).

  • Timer (sets the changeover time, typically 5–15 seconds).

  • Overload relay (thermal or electronic).

  • Interlocks: mechanical and electrical interlocks prevent star and delta contactors closing together (which would be a short circuit).

  • Push buttons (start/stop) and indicators.

Working Sequence

  1. Start: main and star contactors close → motor runs in star.

  2. Motor accelerates to about 75–85% of rated speed.

  3. Timer operates: star contactor opens, delta contactor closes.

  4. Motor runs in delta at full voltage.

Why One-Third

  • In star, phase voltage = V_L / √3 → phase current = 1/√3 of the delta phase current.

  • Line current in delta = √3 × phase current.

  • Line current ratio (star/delta) = (1/√3) / √3 = 1/3.

  • Torque ∝ V², so torque = (1/√3)² = 1/3.

Worked Example

Answer: starting current falls from about 232 A to about 77 A; set the overload to about 22.3 A. A 22 kW, 415 V motor has efficiency 92% and PF 0.86; DOL starting current is 6 times FLC.

  1. FLC = 22,000 / (1.732 × 415 × 0.86 × 0.92) ≈ 38.7 A

  2. DOL starting current ≈ 6 × 38.7 ≈ 232 A

  3. Star starting current ≈ 232 / 3 ≈ 77 A

  4. If the overload relay is in the phase (winding) circuit, set it near FLC / √3 = 38.7 / 1.732 ≈ 22.3 A

Limitations

  • Starting torque is only 1/3, so it is unsuitable for loads with high starting torque.

  • Open transition: a brief power interruption at changeover causes a current and torque spike; closed-transition starters reduce this.

  • Needs six terminals on the motor (both ends of each winding) and six cables.

  • Motor must be rated for delta at the supply voltage.

Common Faults

Wrong timer setting (switching too early gives high current in delta), contactor welding, and missing interlocks.

37

What is a VFD (variable frequency drive)?

A VFD (variable frequency drive) is a power-electronic controller that varies the frequency and voltage supplied to an AC motor to control its speed and torque. Since an induction motor’s speed is set by N_s = 120f/P, changing the frequency changes the speed smoothly. VFDs also give soft starting, save large amounts of energy on fans and pumps, and protect the motor.

Read full answer

Applies toElectrical engineering (power electronics and drives)

Main Sections

Section Function
Rectifier Converts AC supply to DC (diode bridge, or active front end)
DC link (bus) Capacitors (and sometimes chokes) smooth the DC
Inverter IGBTs switch the DC using PWM to create variable-frequency, variable-voltage AC
Control unit Microprocessor controls switching (V/f, vector or direct torque control)

V/f Control

To keep the motor flux constant (avoid saturation or weak torque), voltage is changed in proportion to frequency: V/f = constant below base speed. Above base speed (field weakening), voltage stays at rated value while frequency rises, so torque capability falls.

Worked Example 1: Speed and Voltage

Answer: about 1,050 rpm synchronous speed with about 290 V output. A 4-pole, 415 V, 50 Hz motor is run at 35 Hz.

  • N_s = 120 × 35 / 4 = 1,050 rpm (actual speed slightly less because of slip)

  • V = 415 × 35 / 50 = 290.5 V

Worked Example 2: Energy Saving on a Fan

Answer: about 14.6 kW saved. A 30 kW fan runs at full speed; with a VFD, it runs at 80% speed to meet the airflow needed.

By the affinity laws, power ∝ speed³: - P = 30 × 0.8³ = 30 × 0.512 ≈ 15.4 kW - Saving ≈ 30 − 15.4 = 14.6 kW (compared with full-speed operation; damper control saves far less)

Over 6,000 hours per year at ₹8/kWh, that is about 14.6 × 6,000 × 8 ≈ ₹7 lakh per year.

Benefits

  • Precise speed control and process optimisation.

  • Soft starting (low starting current, about 1–1.5 × FLC).

  • Large energy savings on variable-torque loads (fans, pumps, blowers).

  • Better power factor at the supply (displacement PF close to 1 with a diode front end).

  • Built-in motor protection (overcurrent, overload, phase loss, overvoltage).

Issues and Precautions

  • Harmonics in supply current: use DC chokes, line reactors, 12/18-pulse or active front ends, filters (IEEE 519 limits).

  • Motor insulation stress from fast voltage edges with long cables: use output reactors or dv/dt filters and inverter-duty motors.

  • Bearing currents: insulated bearings or shaft grounding rings on larger motors.

  • Cooling at low speed for self-cooled motors under constant torque.

  • EMC: use shielded cables and proper earthing.

38

What is a synchronous motor, and why is it not self-starting?

A synchronous motor is an AC motor whose rotor runs at exactly synchronous speed (N_s = 120f/P), locked in step with the stator’s rotating magnetic field. Its rotor poles are magnetised by DC excitation (or permanent magnets). It is not self-starting because the stator field rotates at full synchronous speed from the moment of switching on, while the heavy rotor is at rest. The stator poles sweep past the rotor poles so quickly that the torque reverses every half cycle, so the average torque is zero and the rotor only vibrates.

Read full answer

Applies toElectrical engineering (AC machines)

Why No Starting Torque

  • At 50 Hz, the stator field poles pass a given rotor pole 100 times per second (attracting, then repelling).

  • The rotor’s inertia prevents it from following such rapid reversals.

  • Net (average) torque over a cycle = 0.

Starting Methods

Method How it works
Damper (amortisseur) winding Short-circuited bars on the rotor poles start it as an induction motor; DC field applied near synchronous speed to pull into step
Pony motor Small auxiliary motor brings the rotor near N_s, then DC is applied
VFD (variable frequency start) Frequency raised gradually from zero so the rotor stays in step
Starting as a DC machine Exciter used as a motor (older practice)

Characteristics

  • Constant speed at all loads up to the pull-out torque (beyond which it loses synchronism).

  • Adjustable power factor by changing DC excitation:

  • Under-excited: lagging PF.

  • Normal excitation: unity PF.

  • Over-excited: leading PF (acts like a capacitor).

Worked Example

Answer: 1,500 rpm at all loads, and it supplies 60 kVAR leading. A 4-pole, 50 Hz synchronous motor draws 100 kVA at 0.8 PF leading (over-excited).

  • N = 120 × 50 / 4 = 1,500 rpm at any load up to pull-out

  • P = 100 × 0.8 = 80 kW; Q = 100 × 0.6 = 60 kVAR leading, which compensates the lagging kVAR of other loads in the plant

Applications

  • Large constant-speed drives: compressors, mills, pumps, fans in cement and steel plants.

  • Synchronous condensers for power factor and voltage control.

  • Clocks, timers, record turntables (small synchronous motors).

  • PMSMs (permanent magnet synchronous motors) in EVs and high-efficiency drives with VFDs.

39

What is an alternator, and how does it work?

An alternator (synchronous generator) is a machine that converts mechanical energy into AC electrical energy. It works on Faraday’s law: a DC-excited rotor (field) is turned by a prime mover (turbine or engine), so its magnetic field cuts the stationary stator (armature) windings and induces an alternating EMF. The output frequency is fixed by speed and poles: f = P·N / 120.

Read full answer

Applies toElectrical engineering (AC machines and power generation)

Construction

  • Stator (armature): laminated core with three-phase windings; output is taken from stationary terminals (no slip rings for the main current).

  • Rotor (field): DC-excited poles, supplied through slip rings or a brushless exciter.

  • Salient pole rotor: many projecting poles, large diameter, short length; low speed (hydro, diesel).

  • Cylindrical (non-salient) rotor: 2 or 4 poles, long and slender; high speed (steam and gas turbines).

  • Exciter and AVR: supply and regulate the field current to control terminal voltage.

EMF Equation

E_ph = 4.44 · f · Φ · T_ph · K_w

Φ = flux per pole (Wb), T_ph = turns per phase, K_w = winding factor (about 0.9–0.96).

Worked Example

Answer: about 2,109 V per phase, or about 3.65 kV line voltage (star). A 4-pole alternator runs at 1,500 rpm with flux 0.05 Wb per pole, 200 turns per phase and winding factor 0.95.

  1. f = 4 × 1,500 / 120 = 50 Hz

  2. E_ph = 4.44 × 50 × 0.05 × 200 × 0.95 ≈ 2,109 V

  3. E_L = √3 × 2,109 ≈ 3,653 V

Speed and Poles for 50 Hz

Prime mover Speed (rpm) Poles
Steam/gas turbine 3,000 2
Diesel generator (DG set) 1,500 4
Hydro turbine 300 20
Slow hydro 150 40

Why the Field Rotates and the Armature Is Stationary

  • High-voltage, high-current output is taken directly from stationary terminals, so insulation and connections are easier.

  • Only low-power DC excitation passes through slip rings (or none with brushless exciters).

  • The rotor is lighter and can run at high speed safely.

  • The stator winding is easier to cool.

Voltage Control and Operation

  • AVR adjusts excitation to hold voltage with changing load.

  • Governors control the prime mover’s speed (frequency) and active power.

  • Grid-connected alternators must be synchronised before being connected.

40

What is synchronisation of alternators?

Synchronisation is the process of connecting an alternator (or any AC source) in parallel with another alternator or the grid (the “bus”) without causing a large current surge or mechanical shock. Before the breaker is closed, the incoming machine must match the bus in voltage magnitude, frequency, phase sequence and phase angle.

Read full answer

Applies toElectrical engineering (power systems and AC machines)

Conditions for Synchronisation

Condition Why it matters How it is adjusted
Equal voltage (rms) A difference causes circulating reactive current Excitation (AVR) of incoming machine
Equal frequency A difference causes power swings and slipping Governor (prime mover speed)
Same phase sequence (R-Y-B) Wrong sequence causes a severe short circuit Checked once at commissioning with a phase sequence meter
In phase (phase angle near 0°) Closing out of phase causes very high current and torque shock Close breaker at the right instant

In practice, the incoming machine is run very slightly faster than the bus (e.g. 0.05–0.2 Hz higher) so it picks up some load immediately on connection instead of motoring.

Methods

  • Dark lamp method: lamps across the breaker go dark when voltages are in phase.

  • Bright lamp (two bright, one dark) method: shows both phase sequence and the in-phase moment.

  • Synchroscope: pointer rotates at slip frequency; close the breaker when it approaches 12 o’clock while moving slowly in the “fast” direction.

  • Auto-synchroniser and synch-check relay (ANSI 25): automatic matching and closing within set limits.

Worked Example

Answer: the synchroscope makes one revolution every 5 seconds. The incoming alternator runs at 50.2 Hz while the bus is at 50.0 Hz.

  • Slip frequency = 50.2 − 50.0 = 0.2 Hz

  • Time per synchroscope revolution = 1 / 0.2 = 5 seconds

  • With breaker closing time of about 0.1 s, the operator (or auto-synchroniser) gives the close command a little before 12 o’clock so the contacts close at near-zero phase angle.

Typical synch-check limits: voltage difference within about 5–10%, frequency difference within about 0.1–0.2 Hz, phase angle within about 10–20°, depending on machine size and utility rules.

Consequences of Poor Synchronisation

  • High transient currents damaging windings and breakers.

  • Large torque pulses on the shaft and coupling.

  • Tripping of protection and possible loss of the machine.

After Synchronising

  • Active power (kW) sharing is controlled by the governor (fuel or steam input).

  • Reactive power (kVAR) sharing is controlled by excitation.

41

What is the difference between a generator and a motor?

A generator converts mechanical energy into electrical energy, while a motor converts electrical energy into mechanical energy. Both use the same physical principles and similar construction, so the same machine can often work either way. A generator works on Faraday’s law of induction (moving conductors in a field produce EMF), and a motor works on the force on a current-carrying conductor in a magnetic field (F = BIL).

Read full answer

Applies toElectrical engineering (electrical machines)

Comparison

Aspect Generator Motor
Energy conversion Mechanical → electrical Electrical → mechanical
Principle Electromagnetic induction (Faraday) Force on a current-carrying conductor (Lorentz force)
Fleming’s rule Right-hand rule Left-hand rule
Input Shaft driven by turbine or engine Electrical supply
Output Voltage and current Torque and speed
Induced EMF Generated EMF E > V (DC machine) Back EMF E_b < V
Current direction Flows out to the load Flows in from the supply
Examples Alternators in power plants, DG sets, dynamos Pumps, fans, compressors, EV motors

Voltage Equations (DC Machine)

  • Generator: E_g = V + I_a·R_a

  • Motor: E_b = V − I_a·R_a

Worked Example

Answer: 230 V generated as a generator, 210 V back EMF as a motor. A DC machine with armature resistance 0.5 Ω is connected to a 220 V system and carries 20 A of armature current.

  • As a generator delivering 20 A: E_g = 220 + 20 × 0.5 = 230 V

  • As a motor drawing 20 A: E_b = 220 − 20 × 0.5 = 210 V

The machine changes from motor to generator simply when its induced EMF rises above the terminal voltage (for example, when the load drives it faster).

Same Machine, Both Roles

  • Regenerative braking in electric trains, lifts and EVs: the motor works as a generator while slowing down, feeding energy back to the supply or battery.

  • Induction generators in wind turbines: an induction motor driven above synchronous speed generates power.

  • Pumped storage hydro: the same machine runs as a motor (pumping water up) and as a generator (releasing it).

  • Starter-generators in aircraft and some vehicles.

Interview Tip

Mention both the energy direction and the governing principle (induction vs force), and give regenerative braking as a real example of one machine doing both jobs.

42

What is a single-phase induction motor, and why does it need a capacitor?

A single-phase induction motor runs on a single-phase supply (230 V, 50 Hz in India) and is used in fans, pumps, washing machines, refrigerators and other domestic and light commercial equipment. A single-phase winding produces only a pulsating magnetic field, not a rotating one, so the motor has no starting torque on its own. A capacitor in series with an auxiliary winding shifts its current by nearly 90° relative to the main winding, creating a rotating field that starts the motor (and, in capacitor-run motors, improves running performance).

Read full answer

Applies toElectrical engineering (AC machines)

Why It Is Not Self-Starting

  • A single-phase winding produces a field that alternates in one axis.

  • By double revolving field theory, this equals two equal fields rotating in opposite directions at synchronous speed.

  • At standstill, their torques are equal and opposite, so the net torque is zero.

  • Once the rotor is turning in one direction, the torque in that direction becomes larger, so the motor keeps running.

Types

Type Starting method Starting torque Typical use
Split-phase Auxiliary winding with high resistance, cut out by centrifugal switch Low to moderate Small fans, blowers, washing machines (older)
Capacitor-start Capacitor (electrolytic, large µF) with auxiliary winding, cut out by switch High Pumps, compressors, refrigerators
Permanent split capacitor (PSC, capacitor-run) Run capacitor permanently in circuit Low to moderate Ceiling fans, table fans, coolers
Capacitor-start capacitor-run Start and run capacitors High, with good running PF Air conditioners, larger pumps, compressors
Shaded pole Copper shading ring on part of each pole Very low Small fans, hair dryers, exhaust fans

Worked Example

Answer: a 2.25 µF fan capacitor has a reactance of about 1,415 Ω at 50 Hz. A ceiling fan uses a 2.25 µF run capacitor.

X_C = 1 / (2π × 50 × 2.25 × 10⁻⁶) ≈ 1,415 Ω

With the auxiliary winding’s own resistance and reactance, this gives a current in the auxiliary winding leading the main winding current by close to 90°, producing a nearly uniform rotating field.

Common Faults

  • Fan hums but does not start, or runs slowly: a weak or failed capacitor is the most common cause; replace with the same µF and voltage rating (e.g. 2.25 µF or 2.5 µF, 440 V AC for ceiling fans).

  • Motor runs in reverse: auxiliary winding connections reversed.

  • Overheating: wrong capacitor value, bearing problems or low voltage.

Reversing

Reverse the connections of either the main or the auxiliary winding (not both).

43

What are stepper motors and servo motors?

A stepper motor rotates in fixed angular steps in response to digital pulses, so position is set by counting pulses, usually in open loop without feedback. A servo motor is a motor (DC, BLDC or AC synchronous) combined with a feedback device (encoder or resolver) and a controller, working in closed loop to reach and hold a commanded position, speed or torque precisely.

Read full answer

Applies toElectrical engineering (special machines and motion control)

Stepper Motor

  • Types: permanent magnet, variable reluctance, hybrid (most common; 1.8° or 0.9° per step).

  • Step angle = 360° / (steps per revolution).

  • Microstepping divides each step electronically for smoother motion.

  • Holding torque at standstill when energised.

  • Risk: missed steps under overload or too-fast acceleration (open loop does not detect them).

Servo Motor

  • Components: motor, encoder or resolver, servo drive (amplifier), controller.

  • Control loops: current (torque), velocity and position, typically using PID.

  • Corrects errors continuously, with high torque at high speed and fast response.

Worked Example: Stepper Resolution

Answer: 200 steps per revolution and 0.04 mm per full step (0.0025 mm with 1/16 microstepping). A 1.8° hybrid stepper drives a lead screw with 8 mm pitch.

  1. Steps per revolution = 360 / 1.8 = 200

  2. Linear movement per full step = 8 mm / 200 = 0.04 mm

  3. With 1/16 microstepping: 3,200 microsteps per rev → 8 / 3,200 = 0.0025 mm (actual accuracy is lower than the theoretical resolution because of load and motor nonlinearity)

  4. To move 100 mm: 100 / 0.04 = 2,500 full steps

Comparison

Aspect Stepper Servo
Control Open loop (usually) Closed loop
Feedback None (or optional encoder in closed-loop steppers) Encoder or resolver
Torque at high speed Falls sharply Maintained over a wide range
Accuracy Good at low load; steps can be lost High and self-correcting
Response Slower Fast, dynamic
Holding at rest Holding torque, may vibrate Holds position actively
Cost and complexity Low Higher
Tuning Little Needs gain tuning
Heat Draws current even at standstill Current depends on load

Applications

  • Stepper: 3D printers, small CNC routers, plotters, camera sliders, valves, office machines.

  • Servo: industrial robots, CNC machine tools, packaging machines, conveyors needing precise indexing, aircraft control surfaces, RC servos for hobby models.

44

What is a BLDC motor?

A BLDC (brushless DC) motor is a motor with permanent magnets on the rotor and windings on the stator, in which commutation is done electronically by a controller instead of by brushes and a commutator. The controller uses rotor position (from Hall sensors or back-EMF sensing) to switch current through the stator windings in sequence, so the rotor follows the switching. BLDC motors are efficient, compact, quiet and need little maintenance.

Read full answer

Applies toElectrical engineering (special machines and drives)

Working

  1. Rotor magnets set up a field.

  2. The controller energises stator phase pairs (typically six-step / trapezoidal switching, or sinusoidal/FOC control).

  3. The magnetic attraction between stator field and rotor magnets produces torque.

  4. Hall sensors (or sensorless back-EMF detection) tell the controller when to switch to the next step.

  5. Speed is controlled by PWM (voltage) applied to the windings.

Advantages

  • High efficiency (often about 85–90% or more) since there are no rotor copper losses and no brush friction.

  • No brush wear, sparking or commutator maintenance; long life.

  • High torque-to-weight ratio and fast response.

  • Quiet operation and less electrical noise.

  • Precise speed control.

Disadvantages

  • Needs an electronic controller (adds cost and a point of failure).

  • Permanent magnets (rare-earth) add cost and can demagnetise at high temperature.

  • Torque ripple with simple six-step control.

Worked Example: BLDC Ceiling Fan Savings

Answer: about 175 kWh and about ₹1,400 saved per fan per year. A BLDC ceiling fan uses about 32 W compared with about 72 W for a conventional induction fan, and it runs 12 hours a day at ₹8 per unit.

  1. Power saved = 72 − 32 = 40 W

  2. Daily energy saved = 40 × 12 = 480 Wh = 0.48 kWh

  3. Annual saving = 0.48 × 365 ≈ 175 kWh

  4. Money saved ≈ 175 × 8 ≈ ₹1,400 per year

BLDC vs Brushed DC vs Induction

Aspect BLDC Brushed DC Induction
Commutation Electronic Mechanical (brushes) None needed (induced rotor currents)
Efficiency Highest Moderate Good (lower at small sizes)
Maintenance Very low Brush replacement Very low
Controller Required Simple or none VFD needed for speed control

Applications

Ceiling fans (BEE 5-star models), electric two-wheelers and e-rickshaws, drones, computer cooling fans and hard disks, washing machines, air conditioner compressors (inverter AC), pumps, and power tools.

45

What are the main parts of a power system?

A power system is the network that generates electricity and delivers it to consumers. Its main parts are generation (power plants), transmission (high-voltage lines carrying bulk power over long distances), sub-transmission and substations (stepping voltage down), distribution (feeders and transformers supplying consumers) and utilisation (the loads). Protection, control, communication and system operation (load dispatch centres) tie it together.

Read full answer

Applies toElectrical engineering (power systems)

Stages and Typical Indian Voltages

Stage Equipment Typical voltage
Generation Thermal, hydro, nuclear, gas, solar, wind plants; generator transformers 11–25 kV at generator terminals (solar inverter outputs lower)
Transmission Step-up transformers, EHV lines, HVDC links, grid substations 765, 400, 220 kV AC; ±500, ±800 kV HVDC
Sub-transmission Lines and substations 132, 110, 66 kV
Primary distribution 33/11 kV substations, feeders 33 kV, 11 kV (22 kV in some areas)
Secondary distribution Distribution transformers, LT lines, service cables 415 V three-phase, 230–240 V single-phase
Utilisation Homes, industries, commercial loads 230 V / 415 V; large industries at 11–220 kV

Supporting Systems

  • Protection: relays, circuit breakers, CTs, PTs, earthing, lightning arresters.

  • Control and monitoring: SCADA, EMS/DMS, smart meters.

  • System operation: Grid-India (formerly POSOCO) runs the national and regional load dispatch centres, with state load dispatch centres (SLDCs) handling state grids.

  • Communication: PLCC, OPGW fibre, and other links.

Worked Example: Energy Reaching Consumers

Answer: about 80.75 units reach consumers out of 100 generated. A plant generates 100 units; auxiliary consumption is 5%, and transmission and distribution losses are 15% of the energy sent out.

  1. Sent out = 100 × (1 − 0.05) = 95 units

  2. Delivered = 95 × (1 − 0.15) = 80.75 units

So nearly a fifth of the generated energy does not reach consumers, showing why reducing losses is a major focus.

Indian Power Sector Structure

  • Generation: central (NTPC, NHPC, NPCIL), state utilities, private producers, renewable developers.

  • Transmission: POWERGRID (interstate), state transmission utilities, private transmission companies.

  • Distribution: state discoms and private distribution licensees.

  • Regulation and planning: CEA (technical standards and planning), CERC and SERCs (tariffs and regulation).

Interview Tip

Describe the chain from generator to consumer with voltage levels, then mention protection and grid operation; this shows you understand the system as a whole.

46

What are the different types of power plants?

Power plants convert a primary energy source into electricity. The main types are thermal (coal), gas, hydroelectric, nuclear, solar, wind, biomass, geothermal and diesel plants, plus storage such as pumped hydro and battery storage. They differ in fuel, efficiency, cost, flexibility, emissions and whether they serve base load or peak load.

Read full answer

Applies toElectrical engineering (power generation)

Main Types

Type Energy conversion Typical efficiency Role
Coal thermal (Rankine cycle) Coal → heat → steam → turbine → generator About 33–40% (supercritical higher) Base load (largest share in India)
Gas (combined cycle) Gas turbine + heat recovery steam turbine About 50–60% Base/peaking, flexible
Hydroelectric Potential energy of water → turbine About 85–90% Peaking and base, very flexible
Pumped storage Stores energy by pumping water uphill About 70–80% round trip Storage, balancing renewables
Nuclear Fission heat → steam → turbine About 30–35% Base load
Solar PV Sunlight → DC (photovoltaic) → inverter About 18–23% module efficiency Daytime, variable
Wind Kinetic energy → turbine → generator Capacity factor about 25–40% Variable
Biomass Burning biomass → steam About 20–30% Base load, rural
Diesel Internal combustion engine About 35–40% Backup, remote areas

Worked Example 1: Hydro Power

Answer: about 44.1 MW. A hydro plant has flow Q = 50 m³/s, net head H = 100 m and overall efficiency 90%.

P = ρ·g·Q·H·η = 1,000 × 9.81 × 50 × 100 × 0.9 ≈ 44.1 × 10⁶ W = 44.1 MW

Worked Example 2: Thermal Plant Efficiency

Answer: about 35.8% efficiency and 0.6 kg of coal per kWh. A coal plant has a heat rate of 2,400 kcal/kWh and coal with GCV 4,000 kcal/kg.

  1. Efficiency = 860 / 2,400 ≈ 35.8% (1 kWh = 860 kcal)

  2. Coal per kWh = 2,400 / 4,000 = 0.6 kg/kWh

Key Terms

  • Capacity factor = actual energy generated / (rated capacity × hours). A 100 MW solar plant producing 175 GWh in a year has CF = 175,000 / (100 × 8,760) ≈ 20%.

  • Plant load factor (PLF): similar measure used for thermal plants in India.

  • Base load vs peak load plants: base load plants run continuously; peaking plants (hydro, gas, storage) start quickly to meet peaks.

India Context

India’s installed capacity has a growing share of renewables (solar and wind), alongside a large coal fleet. The national target is 500 GW of non-fossil capacity by 2030, which increases the need for storage, flexible generation and grid balancing.

47

Why is power transmitted at high voltage?

Power is transmitted at high voltage because, for the same power, a higher voltage needs a lower current, and line losses depend on the square of current (P_loss = I²R). Raising the voltage by a factor k cuts current by k and losses by k². High voltage also reduces voltage drop and allows smaller conductors, which lowers the cost of transmitting bulk power over long distances.

Read full answer

Applies toElectrical engineering (power systems)

The Physics

For three-phase transmission:

  • I = P / (√3·V·cos φ)

  • P_loss = 3·I²·R = P²·R / (V²·cos²φ)

  • So losses ∝ 1/V² and % voltage drop ∝ 1/V² (for fixed power and line)

Worked Example

Answer: losses fall from about 4.08 MW (40.8%) at 11 kV to about 113 kW (1.13%) at 66 kV, a 36-fold reduction. Send 10 MW at PF 0.9 over a 20 km line with resistance 0.2 Ω/km per phase (4 Ω per phase).

At 11 kV: - I = 10 × 10⁶ / (1.732 × 11,000 × 0.9) ≈ 583.2 A - Loss = 3 × 583.2² × 4 ≈ 4.08 MW (40.8% of the power sent, clearly unworkable)

At 66 kV: - I = 10 × 10⁶ / (1.732 × 66,000 × 0.9) ≈ 97.2 A - Loss = 3 × 97.2² × 4 ≈ 113 kW (1.13%)

Ratio = (66 / 11)² = 36.

Other Benefits

  • Less conductor material for the same losses: conductor volume ∝ 1/V².

  • Better voltage regulation.

  • Higher power transfer capability (surge impedance loading ∝ V²).

  • Fewer parallel lines needed for bulk transfer, saving land (right of way).

Limits on Raising Voltage

  • Insulation: larger insulator strings, taller towers, larger clearances.

  • Corona loss and radio interference: need bundled conductors at EHV.

  • Cost of transformers, switchgear and substations rises.

  • Safety clearances and right of way.

  • So the economic voltage depends on distance and power; very long, high-power links use 765 kV AC or ±800 kV HVDC.

Economic Voltage Rule of Thumb

An empirical formula sometimes quoted: V (kV) ≈ 5.5 × √(L/1.6 + P/(0.8·PF·N)), where L is line length in km and P is power per circuit in kW (used for rough first estimates only).

48

What are the standard transmission and distribution voltages in India?

In India, power is generated at about 11–25 kV, transmitted at 765 kV, 400 kV and 220 kV AC (plus ±500 kV and ±800 kV HVDC), sub-transmitted at 132 kV, 110 kV and 66 kV, distributed at 33 kV and 11 kV (22 kV in some states), and finally supplied to consumers at 415 V three-phase / 240 V single-phase (IS 12360 standardises 400/230 V; distribution transformers are rated 433/250 V on no load). The supply frequency is 50 Hz.

Read full answer

Applies toElectrical engineering (power systems, Indian standards)

Voltage Levels

Level Voltages Use
Generation 11, 13.8, 15.75, 21, 22, 24 kV Generator terminals
Ultra/extra high voltage AC 765 kV, 400 kV National grid, interregional bulk transfer
EHV AC 220 kV State and regional transmission
HVDC ±500 kV, ±800 kV Long-distance bulk transfer (e.g. Raigarh–Pugalur, Champa–Kurukshetra, Biswanath Chariali–Agra)
Sub-transmission 132 kV, 110 kV (some southern states), 66 kV Grid substations to distribution substations
Primary distribution 33 kV, 22 kV, 11 kV Distribution substations, feeders, large consumers
Secondary distribution (LT) 415 V three-phase, 240 V single-phase (nominal 400/230 V) Homes, shops, small industries
Railway traction 25 kV, 50 Hz single-phase AC Overhead equipment

Worked Example: Permissible Voltage Range

Answer: about 216 V to 244 V. Supply regulations have long allowed about ±6% on low-voltage supply. For a nominal 230 V supply:

  • Lower limit = 230 × 0.94 = 216.2 V

  • Upper limit = 230 × 1.06 = 243.8 V

For high voltage (e.g. 11 kV), the traditional limits are +6% / −9%: 10.01 kV to 11.66 kV. (Check the current CEA regulations and state supply code for the applicable limits.)

Why Different Voltage Levels

  • Higher voltages for long distances and bulk power (low losses).

  • Lower voltages closer to consumers for safety and lower equipment cost.

  • Each step uses transformers in substations.

Consumer Supply Categories (Typical)

  • Domestic and small commercial: single-phase 230 V (up to about 5–7 kW in many states), three-phase 415 V for larger loads.

  • Industries: LT up to about 50–100 kVA (varies by state), then HT at 11 kV or 33 kV, and EHT at 66–220 kV for very large loads.

Interview Tip

List the ladder from 765 kV down to 415/230 V with 50 Hz, and mention HVDC and the 25 kV railway system; interviewers check for awareness of current Indian practice.

49

What is the Ferranti effect?

The Ferranti effect is the rise in voltage at the receiving end of a long transmission line (or cable) above the sending-end voltage when the line is lightly loaded or open at the far end. It happens because the line’s shunt capacitance draws a charging current, which flows through the line’s series inductance and produces a voltage rise rather than a drop.

Read full answer

Applies toElectrical engineering (power systems)

Cause

  • Long lines have significant distributed capacitance between conductors and to earth.

  • At light load, the charging (capacitive, leading) current dominates.

  • This leading current flowing through the series inductive reactance produces a voltage across the inductance that adds in phase with the receiving-end voltage, so V_R > V_S.

  • The effect grows with line length, voltage level and frequency, and is stronger in cables (higher capacitance).

Formula (Lossless Line, Open at the Far End)

V_R = V_S / cos(βl)

where β = ω√(LC) ≈ 2πf / v, with v ≈ 3 × 10⁵ km/s for overhead lines. At 50 Hz, β ≈ 0.001047 rad/km (about 0.06° per km).

Approximation for moderate lengths: ΔV / V ≈ (βl)² / 2 = ω²LC·l² / 2.

Worked Example

Answer: about 9.5% rise, so about 438 kV at the open end of a 400 km, 400 kV line.

  1. βl = 0.001047 × 400 ≈ 0.4189 rad

  2. cos(0.4189) ≈ 0.9135

  3. V_R / V_S = 1 / 0.9135 ≈ 1.095

  4. V_R ≈ 400 × 1.095 ≈ 438 kV

(The approximation (βl)²/2 ≈ 8.8% gives a slightly lower estimate.)

Problems Caused

  • Overvoltage stress on insulation and equipment.

  • Difficulty energising long lines from one end.

  • Possible maloperation of protection.

  • Risk to equipment at the receiving end during light load (night-time) periods.

Remedies

  • Shunt reactors at line ends (fixed or switchable) to absorb the capacitive reactive power; standard on 400 kV and 765 kV lines in India.

  • SVC and STATCOM for dynamic reactive power control.

  • Switching off lightly loaded lines or adjusting generator excitation (under-excitation).

  • Tap changers on transformers.

Interview Tip

Explain it as “charging current through line inductance causes a voltage rise,” and give shunt reactors as the main remedy.

50

What is corona discharge in transmission lines?

Corona discharge is the partial ionisation of the air surrounding a high-voltage conductor when the electric field at the conductor surface exceeds the breakdown strength of air (about 30 kV/cm peak, or 21.1 kV/cm rms, at standard conditions). It appears as a faint violet glow, a hissing sound and a smell of ozone, and causes power loss, radio and TV interference and corrosion.

Read full answer

Applies toElectrical engineering (power systems, high-voltage engineering)

Factors Affecting Corona

  • Voltage: corona starts above the critical disruptive voltage.

  • Conductor size: smaller radius → higher surface gradient → more corona.

  • Spacing between conductors: larger spacing reduces the gradient.

  • Surface condition: dirt, scratches and water droplets increase corona (rain and fog make it worse).

  • Atmosphere: lower air density (high altitude, high temperature) reduces breakdown strength.

Critical Disruptive Voltage

V_c = m₀ · g₀ · δ · r · ln(D / r) (kV rms, per phase)

  • m₀ = surface irregularity factor (1 for polished, about 0.8–0.9 for stranded)

  • g₀ = 21.1 kV/cm rms

  • δ = air density factor (1 at 25 °C and 76 cm Hg)

  • r = conductor radius (cm), D = spacing between conductors (cm)

Worked Example

Answer: about 107 kV per phase (about 186 kV line), so a single 2 cm conductor would suffer corona on a 220 kV line. Conductor radius 1 cm, spacing 4 m (400 cm), m₀ = 0.85, δ = 1.

  1. ln(400 / 1) ≈ 5.991

  2. V_c = 0.85 × 21.1 × 1 × 1 × 5.991 ≈ 107.5 kV per phase

  3. Line voltage = √3 × 107.5 ≈ 186 kV

Since 220 kV > 186 kV, corona would occur. Engineers use larger-diameter conductors or bundled conductors.

Effects

Advantages Disadvantages
Reduces steep-fronted surge voltages (acts like a safety valve) Power loss (larger in bad weather)
Effectively increases conductor diameter slightly, reducing gradient Radio, TV and PLCC interference
Ozone production causes conductor corrosion
Audible noise near lines
Non-sinusoidal (harmonic) corona current

Methods to Reduce Corona

  • Bundled conductors (2, 4 or 6 sub-conductors per phase on 220–765 kV lines): increase effective radius and reduce gradient.

  • Larger-diameter conductors (e.g. ACSR, AAAC).

  • Larger phase spacing.

  • Smooth conductor surfaces, corona rings (grading rings) on insulators and fittings.

Interview Tip

Name the threshold (about 30 kV/cm peak), the visible and audible signs, and bundled conductors as the main remedy.

51

What is skin effect?

Skin effect is the tendency of alternating current to flow mainly near the outer surface of a conductor rather than uniformly through its cross-section. Current density is highest at the surface and falls exponentially towards the centre. This reduces the effective cross-sectional area, so the AC resistance is higher than the DC resistance. The effect increases with frequency, conductor diameter, conductivity and magnetic permeability.

Read full answer

Applies toElectrical engineering (power systems and electromagnetics)

Cause

  • Alternating current produces alternating magnetic flux inside the conductor.

  • Flux linkage is greater for the central filaments, so they have higher inductance.

  • Higher inductance opposes current more, pushing current towards the surface.

Skin Depth

δ = √(ρ / (π·f·µ))

  • ρ = resistivity (Ω·m), f = frequency (Hz), µ = µ₀·µ_r (H/m)

  • At depth δ, current density falls to about 37% (1/e) of its surface value.

Worked Example

Answer: about 9.3 mm for copper and about 12 mm for aluminium at 50 Hz. Using ρ_Cu = 1.72 × 10⁻⁸ Ω·m, ρ_Al = 2.82 × 10⁻⁸ Ω·m and µ = 4π × 10⁻⁷ H/m:

  1. π·f·µ = 3.1416 × 50 × 1.2566 × 10⁻⁶ ≈ 1.974 × 10⁻⁴

  2. Copper: δ = √(1.72 × 10⁻⁸ / 1.974 × 10⁻⁴) = √(8.71 × 10⁻⁵) ≈ 9.3 mm

  3. Aluminium: δ = √(2.82 × 10⁻⁸ / 1.974 × 10⁻⁴) ≈ 12 mm

  4. Copper at 1 kHz: δ ≈ 9.3 / √20 ≈ 2.1 mm; at 100 kHz, about 0.21 mm

So skin effect is small for ordinary building wires at 50 Hz but significant for large busbars and conductors, and dominant in high-frequency circuits.

Effects

  • Higher AC resistance → more I²R loss and heating.

  • Less effective use of conductor material in large conductors.

  • In SMPS transformers and RF circuits, the effect is very pronounced.

Remedies and Design Practices

  • Stranded conductors (ACSR, AAAC) for overhead lines.

  • Hollow or tubular conductors and busbars in substations.

  • Flat busbars in parallel strips rather than one thick bar.

  • Litz wire (individually insulated, twisted strands) for high-frequency coils.

  • In ACSR, the steel core carries little current; mostly mechanical strength.

Related: Proximity Effect

Current distribution is also distorted by the magnetic field of nearby conductors carrying current (proximity effect), increasing resistance further in cables and windings.

52

What is a substation, and what equipment does it have?

A substation is a part of the power system where voltage is transformed (stepped up or down), power is switched and routed between lines, and the system is protected, measured and controlled. Main equipment includes power transformers, circuit breakers, isolators, busbars, current and potential transformers, lightning arresters, protective relays, earthing switches, capacitor banks or reactors, and control and communication systems.

Read full answer

Applies toElectrical engineering (power systems)

Types of Substations

Classification Types
Function Step-up (at power plants), step-down (grid, distribution), switching, converter (HVDC), traction
Voltage EHV (765/400/220 kV), HV (132/66 kV), distribution (33/11 kV)
Construction Outdoor (air-insulated, AIS), indoor, gas-insulated (GIS, compact, for cities), pole-mounted

Main Equipment

Equipment Function
Power transformer Changes voltage level
Circuit breaker (SF6, vacuum) Switches circuits and interrupts fault current
Isolator (disconnector) Off-load isolation for maintenance (operated only after the breaker opens)
Earth switch Earths the isolated section for safety
Busbar Common connection point; arrangements like single bus, double bus, one-and-a-half breaker
Current transformer (CT) Steps down current for meters and relays
Potential/voltage transformer (PT/CVT) Steps down voltage for meters and relays; CVT also used for PLCC coupling
Lightning arrester (surge arrester) Diverts lightning and switching surges to earth
Wave trap Blocks PLCC carrier signals from entering the substation
Protective relays Detect faults and trip breakers
Capacitor banks / shunt reactors Reactive power and voltage control
Station transformer and batteries Auxiliary AC and DC supply for control and tripping
Earthing mat (grid) Limits step and touch voltages during faults
SCADA and control panels Monitoring and remote control

Worked Example: Current Ratings

Answer: about 525 A on the 11 kV side and 175 A on the 33 kV side for a 10 MVA 33/11 kV transformer.

  • 11 kV: I = 10 × 10⁶ / (1.732 × 11,000) ≈ 524.9 A

  • 33 kV: I = 10 × 10⁶ / (1.732 × 33,000) ≈ 175 A

These set the CT ratios (e.g. 600/1 A on 11 kV, 200/1 A on 33 kV) and breaker ratings. With two 10 MVA transformers, the firm capacity (N−1) is 10 MVA, so the substation can carry about 9 MW at PF 0.9 if one transformer fails.

Safety Sequence for Isolation

Open breaker → open isolators → close earth switch → test and tag; reverse the order when restoring. Interlocks enforce this sequence.

53

What is the difference between a circuit breaker and a fuse?

A fuse is a simple, one-time protective device: a metal element that melts and breaks the circuit when excess current flows, and must then be replaced. A circuit breaker is a mechanical switching device that opens its contacts automatically on overload or short circuit (and can also be operated manually), and can be reset and reused. Breakers often provide additional protection functions and remote operation.

Read full answer

Applies toElectrical engineering (protection and switchgear)

Comparison

Aspect Fuse Circuit breaker
Operation Element melts (thermal) Contacts open (thermal, magnetic, electronic or relay-controlled)
After operation Replace or rewire Reset and reuse
Speed on short circuit Very fast (HRC fuses can limit current within the first half cycle) Fast (MCB a few ms; HV breakers 2–5 cycles)
Switching function No (protection only) Yes (on/off switching)
Indication Visual on some types Clear on/off indication
Breaking capacity HRC fuses very high (e.g. 80–120 kA) Depends on type (MCB 6–10 kA, ACB 50–100 kA)
Adjustable settings No Yes (MCCB, ACB, relays)
Remote control No Yes (with shunt trip, motor operators)
Cost Low Higher
Earth fault and other protection No Yes (RCBO, relays, electronic trip units)

Worked Example: Rating Selection

Answer: use a 10 A device for a 2 kW heater. A 2 kW heater runs on 230 V.

  • I = 2,000 / 230 ≈ 8.7 A

  • Choose the next standard rating above the load current but within the cable rating: 10 A (fuse or MCB), provided the cable is rated above 10 A (e.g. 1.5 mm² copper, depending on installation method).

The rule: load current ≤ device rating ≤ cable capacity.

Types of Fuses

  • Rewirable (kit-kat): cheap, unreliable rating if wrong wire used.

  • Cartridge / HRC fuses: high rupturing capacity, current-limiting; used for motors, transformers and backup protection.

  • Drop-out (DO) fuses: on 11 kV distribution transformers.

  • Semiconductor fuses: very fast, protect power electronics.

Where Each Is Used

  • Fuses: backup protection, protection of semiconductors, HV distribution transformers (DO fuses), low-cost circuits.

  • Circuit breakers: homes and buildings (MCB, RCCB/RCBO), industrial panels (MCCB, ACB), substations (VCB, SF6).

Interview Tip

Mention that fuses are faster and cheaper with very high breaking capacity, while breakers are reusable and offer switching and adjustable protection, so they are often used together (fuse as backup).

54

What are the types of circuit breakers (MCB, MCCB, ACB, VCB, SF6)?

Circuit breakers are classified mainly by voltage level, current rating and arc-quenching medium. Low-voltage types are the MCB (miniature, up to about 125 A), MCCB (moulded case, up to about 1,600–2,500 A) and ACB (air circuit breaker, up to about 6,300 A). Medium and high-voltage types include the VCB (vacuum, mainly 3.3–33 kV) and the SF6 breaker (66 kV to 765 kV and above, also in GIS).

Read full answer

Applies toElectrical engineering (switchgear and protection)

Comparison

Type Voltage Current range Breaking capacity (typical) Arc quenching Typical use
MCB LV (230/415 V) 0.5–125 A 6–10 kA (up to 25 kA) Arc chute in air Homes, offices, final circuits
MCCB LV 16–1,600 A (up to about 2,500 A) 25–100 kA Air with arc chutes Industrial feeders, distribution panels, motor feeders
ACB LV 630–6,300 A 50–100 kA or more Air, arc chutes Main incomers from transformers, PCCs
VCB 3.3–33 kV (some up to 72.5 kV) 630–4,000 A 25–50 kA Vacuum interrupter Distribution substations, industrial HT panels
SF6 33–800 kV 1,250–4,000 A or more 25–63 kA SF6 gas Transmission substations, GIS
Oil (bulk/minimum oil) 11–220 kV Various Various Oil Older installations, largely replaced

MCB Trip Curves

Curve Instantaneous trip Use
B 3–5 × In Lighting, resistive loads, long cables
C 5–10 × In General, small motors, mixed loads
D 10–20 × In Motors, transformers, high inrush

Worked Example: Selecting an ACB

Answer: a 1,600 A ACB with breaking capacity of at least about 30 kA (50 kA standard). A 1,000 kVA, 11 kV/433 V transformer with 5% impedance feeds the main LT panel.

  1. Full-load current = 1,000,000 / (1.732 × 433) ≈ 1,333 A → choose a 1,600 A ACB

  2. Maximum fault current (infinite source) ≈ 1,333 / 0.05 ≈ 26.7 kA

  3. Choose a breaking capacity above this with margin, e.g. 50 kA (common standard rating)

Key Features

  • MCCB/ACB: adjustable thermal-magnetic or microprocessor trip units (long time, short time, instantaneous, earth fault: LSIG).

  • VCB: compact, long life, little maintenance, suitable for frequent switching.

  • SF6: excellent insulation and arc quenching, but SF6 is a very strong greenhouse gas, so leak monitoring is essential and SF6-free alternatives are emerging.

Interview Tip

Group them by voltage: MCB/MCCB/ACB for LV, VCB for MV, SF6 for HV/EHV, and explain the arc-quenching medium for each.

55

What is the difference between MCB, RCCB and ELCB?

An MCB (miniature circuit breaker) protects cables and equipment against overload and short circuit. An RCCB (residual current circuit breaker) protects people against electric shock and earth-leakage fires by detecting imbalance between phase and neutral currents; it does not protect against overload. An ELCB (earth leakage circuit breaker) is the older term; the original voltage-operated ELCB detected voltage on the earth wire, while today “ELCB” is often loosely used for current-operated RCCBs.

Read full answer

Applies toElectrical engineering (LV protection and building wiring)

Comparison

Aspect MCB RCCB ELCB (voltage-operated, older type)
Protects against Overload, short circuit Earth leakage, electric shock Earth leakage (only through the monitored earth wire)
Sensing Thermal (bimetal) + magnetic (coil) Core-balance transformer measures phase − neutral Coil between equipment earth and a separate reference earth
Ratings 0.5–125 A; B/C/D curves Rated current (25–100 A) + sensitivity (10, 30, 100, 300 mA) —
Protects people? No Yes (30 mA type) Partly; unreliable
Protects cables from overload? Yes No No
Current use Standard Standard (required in many installations) Obsolete

An RCBO combines MCB and RCCB functions in one device.

How an RCCB Works

  1. Phase and neutral pass through a toroidal core.

  2. Normally the currents are equal and opposite, so net flux is zero.

  3. If current leaks to earth (e.g. through a person or faulty insulation), the imbalance induces a current in a sensing coil.

  4. When imbalance exceeds the rated sensitivity (I_Δn), the RCCB trips.

Worked Example

Answer: the 30 mA RCCB trips within about 40 ms. A person touches a live 230 V conductor with a body-to-earth path resistance of about 1,000 Ω.

  • Leakage current = 230 / 1,000 = 230 mA

  • This exceeds 5 × I_Δn = 150 mA, so a general-type RCCB (IEC 61008) must trip within 40 ms

  • An MCB would not trip at all, because 0.23 A is far below its rating

Sensitivity Selection

I_Δn Purpose
10 mA Special locations (bathrooms in some practices, medical)
30 mA Personal protection (sockets, bathrooms, outdoor)
100 mA Equipment protection, discrimination
300 mA Fire protection, upstream main protection

Types of RCCB

  • AC type: sinusoidal leakage only.

  • A type: also pulsating DC (for appliances with electronics, washing machines, inverters).

  • B type: smooth DC too (EV chargers, solar inverters, VFDs).

Interview Tip

The MCB protects the wiring; the RCCB protects the person. Use both (or an RCBO) in every installation.

56

What are relays, and how do overcurrent, differential and distance relays differ?

A relay is a device that senses an abnormal condition (such as overcurrent, earth fault, or abnormal impedance) through CTs and PTs, and sends a trip signal to a circuit breaker. Overcurrent relays trip when current exceeds a set value, with a time delay that usually falls as current rises. Differential relays compare the currents entering and leaving a protected zone and trip if they differ, giving fast protection for transformers, generators and busbars. Distance relays measure impedance (V/I) to the fault and trip when it falls below a set reach, protecting transmission lines.

Read full answer

Applies toElectrical engineering (power system protection)

Comparison

Aspect Overcurrent Differential Distance (impedance)
Measures Current magnitude Difference of currents into and out of a zone Impedance (V/I) to the fault
Principle Trips when I > pickup (with time grading) Kirchhoff: in = out for healthy zone Fault impedance ∝ distance to fault
Selectivity By time and current grading Absolute (only its zone) By zones (Zone 1, 2, 3)
Speed Inverse-time delay Very fast (tens of ms) Zone 1 instantaneous
Typical use Feeders, motors, backup Transformers, generators, busbars, cables Transmission lines (66 kV and above)

Overcurrent Relay (IDMT)

IEC standard inverse: t = TMS × 0.14 / (PSM^0.02 − 1)

PSM = plug setting multiplier = fault current / pickup current.

Worked Example: IDMT Operating Time

Answer: about 0.59 seconds. A relay has pickup 400 A (CT 400/1, plug setting 100%), TMS = 0.2, and the fault current is 4,000 A.

  1. PSM = 4,000 / 400 = 10

  2. 10^0.02 ≈ 1.0471

  3. t = 0.2 × 0.14 / (1.0471 − 1) = 0.2 × 0.14 / 0.0471 ≈ 0.2 × 2.97 ≈ 0.594 s

The upstream relay is graded with a margin (about 0.3–0.4 s) so the nearest relay trips first.

Differential Relay

  • Percentage (biased) differential relays allow for CT errors and tap changes.

  • For transformers: compensate for vector group and ratio; block or restrain during magnetising inrush (second harmonic restraint).

Distance Relay Zones (Typical)

  • Zone 1: about 80% of the line, instantaneous.

  • Zone 2: 100% of the line plus about 20–50% of the next line, time delay about 0.3–0.4 s.

  • Zone 3: backup for adjacent lines, about 0.8–1.0 s.

Modern numerical relays combine many functions (overcurrent, earth fault, differential, distance, breaker failure, disturbance recording) in one IED, with IEC 61850 communication.

57

What is earthing, and why is it important?

Earthing (grounding) is connecting the non-current-carrying metal parts of electrical equipment, or the neutral of a supply system, to the general mass of the earth through a low-resistance path. It protects people from electric shock by keeping exposed metal parts near earth potential and providing a path for fault current, so that fuses, MCBs or RCCBs operate quickly. It also stabilises system voltages and safely discharges lightning and static.

Read full answer

Applies toElectrical engineering (safety and installations; IS 3043 and the CEA Safety Regulations)

Two Kinds of Earthing

  • System (neutral) earthing: neutral of transformers and generators connected to earth; stabilises voltage and allows earth fault protection.

  • Equipment (protective) earthing: metal frames, enclosures and conduits connected to earth through protective conductors.

Why It Is Important

  1. Safety: limits touch voltage on equipment frames during faults.

  2. Fault clearing: low-impedance path → large fault current → protective devices trip fast.

  3. Voltage stability: prevents the neutral from floating to dangerous levels.

  4. Lightning and surge protection: diverts surge currents to earth.

  5. Static discharge: in fuel stations, plants and hospitals.

  6. Equipment protection: reduces damage and fire risk.

Worked Example: Why Earthing Alone May Not Clear a Fault

Answer: the fault current is about 21 A and the frame rises to about 209 V, so an RCCB is needed. In a TT installation, the consumer’s earth electrode has 10 Ω resistance and the supply neutral earth has 1 Ω. A live wire touches an appliance’s metal body.

  1. Fault current = 230 / (10 + 1) ≈ 20.9 A

  2. A 32 A MCB will not trip (and even a 16 A C-curve MCB will not trip instantly at this current)

  3. Frame voltage to earth ≈ 20.9 × 10 ≈ 209 V, which is dangerous

With a 30 mA RCCB, the RCCB trips at once. The condition R_A × I_Δn ≤ 50 V (10 × 0.03 = 0.3 V) is easily met, so the installation is safe.

Good Earthing Practice

  • Earth resistance as low as practicable. Commonly quoted targets are 1 Ω or less for large substations, 2–5 Ω for industrial installations and up to about 5–8 Ω for domestic installations, but the protective device coordination and IS 3043 calculations govern.

  • At least two separate earth electrodes for important installations, interconnected.

  • Proper earth continuity conductor sizes (IS 732/IS 3043).

  • Regular testing with an earth tester (three-point method), especially in the dry season.

  • Never use the neutral as earth or connect the earth to the neutral within the consumer premises, except where the system design (TN-C-S) specifies it.

58

What are the types of earthing?

Earthing types can be grouped in two ways: by electrode type (how the connection to earth is made: pipe, plate, rod, strip, chemical/maintenance-free earthing and earth mats) and by system earthing arrangement (how the supply neutral and equipment frames are earthed: TN-S, TN-C, TN-C-S, TT and IT systems). Both are covered in IS 3043.

Read full answer

Applies toElectrical engineering (installations and safety)

Electrode Types

Type Description Typical use
Pipe earthing GI pipe (about 40 mm diameter, about 2.5–3 m long) with charcoal and salt layers, watering funnel Common in Indian buildings (older practice)
Plate earthing Copper or GI plate (about 600 × 600 mm) buried at about 1.5–3 m Substations, transformers, older installations
Rod earthing Copper-bonded steel rods driven vertically Buildings, lightning protection, where soil allows driving
Strip/wire earthing Copper or GI strips laid horizontally in trenches Rocky areas, interconnecting electrodes
Chemical (maintenance-free) earthing Electrode in conductive backfill compound Modern buildings, telecom, data centres
Earth mat/grid Mesh of conductors with rods Substations (controls step and touch voltage)

System Earthing Arrangements

System Neutral Exposed metal parts Notes
TN-S Earthed at source Separate protective earth conductor from source Good safety, common in industry
TN-C Earthed at source Combined PEN conductor Not allowed for final circuits in many codes
TN-C-S (PME) Earthed at source Combined PEN in supply network, separated at consumer Common in urban supply
TT Earthed at source Consumer’s own earth electrode Needs RCDs; common in Indian domestic supply
IT Isolated or high-impedance earthed Earthed locally Continuity of supply (hospitals, mines, some industries)

Worked Example: Rod Electrode Resistance

Answer: about 30 Ω, so one rod is not enough. A single rod 3 m long and 16 mm in diameter is driven into soil with resistivity 100 Ω·m. Using R = (ρ / 2πL) × [ln(4L/d) − 1]:

  1. ρ / 2πL = 100 / (2π × 3) ≈ 5.31

  2. 4L/d = 12 / 0.016 = 750 → ln(750) ≈ 6.62 → 6.62 − 1 = 5.62

  3. R ≈ 5.31 × 5.62 ≈ 29.8 Ω

To reduce it: use several rods in parallel (spaced at least about twice the rod length apart), longer rods, chemical backfill, or treat the surrounding soil.

Choosing an Earthing System

Depends on soil resistivity, fault level, installation type (home, industry, substation, telecom), space, and maintenance capability. Measure soil resistivity (Wenner four-electrode method) before design.

Maintenance

  • Test earth resistance regularly, preferably in the dry season.

  • Keep connections tight and corrosion-free.

  • Water pipe or plate pits as needed (not needed for maintenance-free types).

59

What are short-circuit faults, and what are symmetrical and unsymmetrical faults?

A short-circuit fault is an abnormal low-impedance connection between phases, or between phase(s) and earth, that causes very high currents. Symmetrical faults affect all three phases equally (a three-phase fault, with or without earth), so the system stays balanced and can be analysed per phase. Unsymmetrical faults affect phases unequally (single line-to-ground, line-to-line, double line-to-ground) and need symmetrical components for analysis.

Read full answer

Applies toElectrical engineering (power system analysis and protection)

Types and Frequency of Occurrence (Typical for Overhead Lines)

Fault type Symbol Approximate share Severity
Single line-to-ground LG About 70–80% Usually least severe
Line-to-line LL About 10–15% Moderate
Double line-to-ground LLG About 10% Severe
Three-phase (with or without earth) LLL / LLLG About 2–5% Usually most severe; used for breaker rating

Causes

Insulation failure, lightning, tree contact, birds and animals, conductor breakage, human error, equipment failure, flashover due to pollution.

Effects

  • Very high currents → overheating and mechanical forces on conductors and windings.

  • Voltage dips across the system.

  • Loss of stability and possible blackouts.

  • Fire and arc flash hazards.

Worked Example: Three-Phase Fault Current

Answer: about 13.3 kA. A 500 kVA, 11 kV/433 V transformer with 5% impedance (infinite source assumed).

  1. Full-load current = 500,000 / (1.732 × 433) ≈ 666.7 A

  2. Fault current = 666.7 / 0.05 ≈ 13.3 kA

With source impedance and cable impedance included, the actual value is somewhat lower; breakers on this panel need a breaking capacity above 13.3 kA (e.g. 25 kA or more).

Symmetrical Components

Any unbalanced set of three-phase phasors can be resolved into: - Positive sequence (balanced, normal rotation) - Negative sequence (balanced, reverse rotation) - Zero sequence (three equal phasors in phase)

For an LG fault: I_f = 3E / (Z₁ + Z₂ + Z₀ + 3Z_f). LG fault current can exceed the three-phase value close to solidly earthed generators or transformers with low zero-sequence impedance.

Protection

Overcurrent and earth fault relays, distance relays, differential relays, fuses and breakers rated for the maximum fault level.

60

What is the per-unit system?

The per-unit (pu) system expresses electrical quantities (voltage, current, power, impedance) as fractions of chosen base values: quantity in pu = actual value / base value. It is used in power system analysis because it removes the need to refer impedances across transformers, makes equipment parameters fall in narrow, comparable ranges, and simplifies hand and computer calculations.

Read full answer

Applies toElectrical engineering (power system analysis)

Choosing Base Values

  • Choose a base MVA (common to the whole system, e.g. 100 MVA).

  • Choose a base kV in one zone; other zones’ base kV follow the transformer ratios.

  • Derived bases:

  • Z_base = (kV_base)² / MVA_base (Ω)

  • I_base = MVA_base / (√3 × kV_base) (kA)

Change of Base

Z_pu(new) = Z_pu(old) × (MVA_new / MVA_old) × (kV_old / kV_new)²

Worked Example

Answer: generator reactance becomes 0.4 pu, and a 30 Ω line on 132 kV is about 0.172 pu (100 MVA base).

  1. A generator rated 50 MVA, 11 kV has X = 0.2 pu on its own rating. On a 100 MVA, 11 kV base: X = 0.2 × (100 / 50) = 0.4 pu

  2. For the 132 kV zone: Z_base = 132² / 100 = 174.24 Ω; a line of 30 Ω → 30 / 174.24 ≈ 0.172 pu

  3. Base current at 132 kV: I_base = 100 / (1.732 × 132) ≈ 0.437 kA = 437 A

For a three-phase fault at a bus fed through a total of 0.572 pu (0.4 + 0.172, ignoring the transformer for simplicity): I_f = 1 / 0.572 ≈ 1.75 pu = 1.75 × 437 ≈ 765 A at 132 kV.

Advantages

  • Transformers disappear: with properly chosen bases, the per-unit impedance of a transformer is the same from either side.

  • Typical ranges make errors easy to spot: transformer impedance about 0.04–0.15 pu, generator subtransient reactance about 0.1–0.3 pu.

  • Simpler three-phase calculations: √3 factors largely cancel.

  • Easy comparison of machines of different ratings.

  • Standard input format for load flow and fault study software.

Typical Nameplate Values

  • Distribution transformer impedance: about 4–6%.

  • Power transformer: about 10–15%.

  • Generator X″d: about 0.12–0.25 pu.

61

What is load flow analysis?

Load flow (power flow) analysis is the steady-state calculation of voltage magnitude and phase angle at every bus in a power network, for given generation and load. From these, it gives real and reactive power flows in every line and transformer, and the system losses. It is the most widely used power system study, needed for planning, operation, contingency analysis and as the starting point for fault and stability studies.

Read full answer

Applies toElectrical engineering (power system analysis)

Bus Types

Bus type Known (specified) Unknown (calculated)
Slack (swing / reference) bus V and δ (usually 1.0 pu, 0°) P and Q (balances losses)
PV (generator) bus P and voltage magnitude Q and δ
PQ (load) bus P and Q Voltage magnitude and δ

Power Flow Equations

For bus i: P_i − jQ_i = V_i* × Σ (Y_ik × V_k), using the bus admittance matrix (Y-bus). These equations are non-linear, so they are solved iteratively.

Solution Methods

Method Features
Gauss-Seidel Simple, low memory, slow convergence, many iterations
Newton-Raphson Fast (quadratic) convergence, few iterations, standard for large systems
Fast decoupled Uses P–δ and Q–V decoupling; very fast, good for repeated studies
DC load flow Linear approximation (only P and δ); quick contingency screening

Worked Example (Two-Bus, Simplified)

Answer: an angle difference of about 11.5°. Two buses at 1.0 pu are linked by a lossless line of reactance 0.2 pu, and 1.0 pu power (100 MW on a 100 MVA base) flows between them.

P = (V₁·V₂ / X) × sin δ → 1.0 = (1 × 1 / 0.2) × sin δ → sin δ = 0.2 → δ ≈ 11.5°

The maximum (steady-state stability limit) for this line is V₁V₂/X = 5 pu (500 MW), reached at δ = 90°.

Outputs

  • Bus voltages (check they are within limits, e.g. 0.95–1.05 pu).

  • Line loadings (check thermal limits).

  • Real and reactive power losses.

  • Reactive power needs (where to add capacitors or reactors).

Applications

  • Planning new lines, substations and generation.

  • Contingency analysis (N−1): checking what happens when a line or generator trips.

  • Optimal power flow and economic dispatch.

  • Integration studies for renewable plants.

  • Software: PSS/E, ETAP, PowerWorld, DIgSILENT PowerFactory, MiPower.

62

What is a power grid, and what is grid frequency?

A power grid is the interconnected network of power plants, transmission lines, substations and distribution systems that delivers electricity from generators to consumers. Grid frequency is the frequency of the AC voltage across the synchronised grid (50 Hz in India). All synchronous generators in the grid rotate in step at a speed matching this frequency, so it acts as a real-time indicator of the balance between generation and load.

Read full answer

Applies toElectrical engineering (power systems and grid operation)

Indian Grid

  • India operates one synchronous national grid (“One Nation, One Grid, One Frequency”), formed by linking the five regional grids (Northern, Eastern, Western, North-Eastern, Southern), with the Southern grid synchronised in 2013.

  • Operated by Grid Controller of India (Grid-India) through the National, Regional and State Load Dispatch Centres.

  • The Indian Electricity Grid Code (IEGC) sets the normal frequency band, currently 49.90–50.05 Hz.

Frequency and Balance

  • Generation > load → excess energy speeds up generators → frequency rises.

  • Load > generation → generators slow down → frequency falls.

  • Generator speed: N = 120f / P (e.g. 3,000 rpm for a 2-pole machine at 50 Hz).

Frequency Control Layers

Layer Timescale Mechanism
Inertia Instant Stored kinetic energy in rotating machines slows the fall
Primary control Seconds Governor droop response (typically about 3–6% droop)
Secondary control (AGC) Tens of seconds to minutes Automatic generation control restores frequency and schedules
Tertiary control Minutes to hours Re-dispatch, reserves, market actions

Under-frequency load shedding relays disconnect loads in stages if frequency falls too far, preventing collapse.

Worked Example

Answer: frequency settles about 0.2 Hz lower, at about 49.8 Hz. A 1,000 MW generator trips; assume the grid’s combined frequency response characteristic is 5,000 MW/Hz (an illustrative figure).

Δf = ΔP / β = 1,000 / 5,000 = 0.2 Hz → steady frequency ≈ 49.8 Hz (after primary response, before secondary control restores 50 Hz)

Why Frequency Must Be Stable

  • Motor speeds and clocks depend on it.

  • Turbine blades can resonate at off-nominal frequencies.

  • Large deviations trip generators and can cause cascading blackouts (e.g. the July 2012 Indian grid disturbances).

  • Growing solar and wind (inverter-based, low inertia) make frequency control harder, increasing the need for storage and fast reserves.

63

What is a rectifier, and how do half-wave and full-wave rectifiers differ?

A rectifier is a circuit that converts AC into DC using diodes (or thyristors for controlled rectifiers). A half-wave rectifier passes only one half of each AC cycle, giving a low, highly pulsating output. A full-wave rectifier (centre-tapped or bridge) uses both halves, giving twice the average output voltage, half the ripple, and better transformer use.

Read full answer

Applies toElectrical engineering (power electronics)

Comparison

Aspect Half-wave Full-wave (centre-tap) Full-wave (bridge)
Diodes 1 2 4
Average output V_dc V_m / π ≈ 0.318V_m 2V_m / π ≈ 0.637V_m 2V_m / π ≈ 0.637V_m
RMS output V_m / 2 V_m / √2 V_m / √2
Ripple frequency (50 Hz input) 50 Hz 100 Hz 100 Hz
Ripple factor 1.21 0.48 0.48
Efficiency (max, resistive load) 40.6% 81.2% 81.2%
PIV per diode V_m 2V_m V_m
Transformer Simple, poor use (DC saturation) Centre-tapped needed No centre tap needed

Worked Example

Answer: about 5.4 V (half-wave) versus about 9.9 V (bridge, with diode drops). A 230/12 V transformer feeds a rectifier with a resistive load.

  1. V_m = 12 × √2 ≈ 16.97 V

  2. Half-wave (ideal): V_dc = 16.97 / π ≈ 5.40 V

  3. Bridge (ideal): V_dc = 2 × 16.97 / π ≈ 10.8 V

  4. Bridge with two diode drops (2 × 0.7 V): V_m’ = 15.57 V → V_dc ≈ 2 × 15.57 / π ≈ 9.91 V

Filter Capacitor

Adding a capacitor across the load keeps the voltage near peak. Peak-to-peak ripple ≈ I / (f_r × C): - For a 1 A load, a full-wave rectifier (f_r = 100 Hz) and 4,700 µF: ΔV ≈ 1 / (100 × 0.0047) ≈ 2.13 V - A half-wave rectifier (50 Hz) would need twice the capacitance for the same ripple.

Applications

  • Half-wave: very low-power, low-cost circuits, signal detection.

  • Full-wave bridge: power supplies, battery chargers, SMPS front ends, DC motor drives.

  • Three-phase bridges (6-pulse, 12-pulse): VFDs, HVDC, electroplating, large DC supplies.

64

What is an inverter?

An inverter is a power-electronic device that converts DC into AC at a desired voltage and frequency. It uses semiconductor switches (MOSFETs or IGBTs) switched on and off rapidly, often with PWM (pulse-width modulation), followed by filtering, to create an AC waveform. Inverters are used for home power backup, solar PV systems, motor drives (VFDs), UPS systems and electric vehicles.

Read full answer

Applies toElectrical engineering (power electronics)

Types by Output Waveform

Type Output Notes
Square wave Square wave Cheap; high harmonics; unsuitable for many loads
Modified (quasi) sine wave Stepped waveform Works for many loads; motors and some electronics run hot or noisy
Pure sine wave Low-distortion sine (THD often below 3–5%) Suitable for all loads, including motors and sensitive electronics

Types by Application

  • Home inverters (battery backup): charge batteries from the mains and supply AC during outages.

  • Solar inverters: string, central, micro-inverters; on-grid (grid-tied), off-grid and hybrid.

  • VFD inverters: variable frequency and voltage for motor speed control.

  • Traction inverters: in EVs and trains.

Basic Circuit

  • Single-phase full bridge (H-bridge): four switches; pairs switch alternately to apply +V and −V across the load.

  • Three-phase bridge: six switches (used in VFDs and solar central inverters).

  • PWM: switching at several kHz to tens of kHz, with the duty cycle varied sinusoidally, then filtered by LC filters to produce a clean sine wave.

Worked Example: Home Inverter Backup Time

Answer: about 3 hours, with about 39 A drawn from the battery. A 12 V, 150 Ah battery supplies a 400 W load through an inverter with 85% efficiency, using 80% of the battery capacity.

  1. Battery energy = 12 × 150 = 1,800 Wh

  2. Usable = 1,800 × 0.8 = 1,440 Wh

  3. Delivered to load = 1,440 × 0.85 = 1,224 Wh

  4. Backup time = 1,224 / 400 ≈ 3.06 hours

  5. Battery current = 400 / (12 × 0.85) ≈ 39.2 A

(In practice, high discharge rates reduce lead-acid battery capacity, so actual backup is usually less.)

Key Specifications

VA/W rating, input DC voltage, output waveform and THD, efficiency, surge capacity, charging current, transfer time, protections (overload, short circuit, low battery, overtemperature).

65

What is a thyristor (SCR), and how is it triggered?

A thyristor or SCR (silicon-controlled rectifier) is a four-layer (P-N-P-N), three-terminal semiconductor switch with anode, cathode and gate. It blocks current in both directions until a small gate pulse is applied while it is forward biased; it then turns on and keeps conducting (latches) even after the gate signal is removed, until the anode current falls below the holding current. It is used to control large AC and DC power.

Read full answer

Applies toElectrical engineering (power electronics)

Operating Modes

Mode Condition State
Reverse blocking Anode negative Off (small leakage)
Forward blocking Anode positive, no gate pulse Off (until breakover)
Forward conduction Anode positive, triggered On (low voltage drop, about 1–2 V)

Key currents: - Latching current: minimum anode current needed immediately after triggering to keep the SCR on. - Holding current: minimum anode current to stay on; below this the SCR turns off. Latching current is higher than holding current.

Triggering (Turn-On) Methods

  1. Gate triggering (normal method): a positive gate pulse relative to the cathode.

  2. Forward voltage triggering: exceeding the forward breakover voltage (not used deliberately; can damage the device).

  3. dv/dt triggering: a fast-rising anode voltage causes capacitive current that turns it on (unwanted; prevented by snubbers).

  4. Temperature triggering: high temperature increases leakage (unwanted).

  5. Light triggering: in light-activated SCRs (LASCR), used in HVDC valves.

Gate circuits: R, RC, UJT relaxation oscillators, and microcontroller or dedicated ICs with pulse transformers or opto-isolation.

Turn-Off (Commutation)

  • Natural (line) commutation: in AC circuits the current falls to zero each half cycle.

  • Forced commutation: in DC circuits, an auxiliary circuit forces the current to zero (largely replaced by IGBTs today).

Worked Example: Phase Control

Answer: about 155 V DC at a 60° firing angle. A single-phase full-wave controlled rectifier with a resistive load is fed from 230 V, 50 Hz.

  1. V_m = 230 × √2 ≈ 325.3 V

  2. V_dc = (V_m / π)(1 + cos α) = (325.3 / π)(1 + 0.5) ≈ 103.55 × 1.5 ≈ 155.3 V

  3. At α = 0°: 207 V; at α = 90°: 103.5 V; at α = 180°: 0 V

Applications

Controlled rectifiers, AC voltage controllers (dimmers, heater controls), soft starters, HVDC converters, static switches, crowbar protection, and large DC drives.

66

What is the difference between an SCR, a TRIAC, a MOSFET and an IGBT?

SCRs, TRIACs, MOSFETs and IGBTs are power semiconductor switches with different control and performance features. An SCR conducts in one direction and can only be turned on by the gate (it turns off when current falls to zero). A TRIAC is like two SCRs in anti-parallel, conducting in both directions for AC control. A MOSFET is a voltage-controlled, fully controllable switch that is very fast and efficient at low to medium voltage. An IGBT combines MOSFET-like gate control with bipolar conduction, suiting medium to high voltage and power at moderate switching frequencies.

Read full answer

Applies toElectrical engineering (power electronics)

Comparison

Aspect SCR TRIAC MOSFET IGBT
Terminals Anode, cathode, gate MT1, MT2, gate Drain, source, gate Collector, emitter, gate
Conduction Unidirectional Bidirectional Unidirectional (body diode in reverse) Unidirectional
Control Current pulse, turn-on only Current pulse, turn-on only Voltage-controlled on and off Voltage-controlled on and off
Switching speed Slow (line frequency) Slow Very fast (100 kHz to MHz) Medium (a few kHz to about 50 kHz)
Voltage range Very high (up to about 8–12 kV per device) Low to medium (up to about 1 kV) Low to medium (up to about 1 kV; SiC higher) Medium to high (600 V to about 6.5 kV)
Current range Very high (kA) Low to medium Medium High
On-state behaviour About 1–2 V drop About 1–2 V drop Resistive (R_DS(on)) About 1.5–3 V (V_CE(sat))
Typical uses HVDC, controlled rectifiers, soft starters Light dimmers, fan regulators, small AC controls SMPS, DC-DC converters, chargers, low-voltage motor drives VFDs, inverters, EV traction, welding, UPS

Worked Example: Conduction Loss

Answer: the MOSFET loses about 4 W and the IGBT about 36 W at 20 A. A MOSFET with R_DS(on) = 10 mΩ and an IGBT with V_CE(sat) = 1.8 V each carry 20 A continuously.

  • MOSFET: P = I² × R = 20² × 0.01 = 4 W

  • IGBT: P = V × I = 1.8 × 20 = 36 W

At low voltage and moderate current, MOSFETs are more efficient. At high voltage, a MOSFET’s R_DS(on) rises steeply, so IGBTs win (wide-bandgap SiC MOSFETs are changing this boundary).

Choosing a Device

  • Line-frequency, very high power: SCR.

  • Simple AC phase control at low power: TRIAC.

  • High-frequency, low-voltage: MOSFET (GaN for very high frequency).

  • Medium/high voltage, kW to MW drives: IGBT (SiC MOSFETs increasingly in EVs and solar).

67

What is a chopper (DC-DC converter)?

A chopper is a DC-DC converter that changes one DC voltage level into another by switching a semiconductor device (MOSFET or IGBT) on and off rapidly and controlling the duty cycle (D = T_on / T). Inductors and capacitors smooth the output. The main types are the buck (step-down), boost (step-up) and buck-boost converters, used in power supplies, battery chargers, EVs, solar MPPT and DC motor drives.

Read full answer

Applies toElectrical engineering (power electronics)

Main Types (Ideal, Continuous Conduction)

Type Output voltage Function
Buck (step-down) V_o = D · V_in Lower output voltage
Boost (step-up) V_o = V_in / (1 − D) Higher output voltage
Buck-boost V_o = −D · V_in / (1 − D) Higher or lower, inverted polarity
Ćuk, SEPIC Similar ratios with different features Non-inverting or low ripple variants
Isolated (flyback, forward, full-bridge) Includes transformer turns ratio Isolation in SMPS

Control

  • PWM (constant frequency, varying duty cycle) is the usual method.

  • Frequency modulation or current-limit control are alternatives.

  • Feedback regulates output voltage despite load and input changes.

Worked Example

Answer: D = 0.25 for 48 V → 12 V (buck), D = 0.75 for 12 V → 48 V (boost), and an inductor ripple of about 1.9 A.

  1. Buck from 48 V to 12 V: D = 12 / 48 = 0.25

  2. Boost from 12 V to 48 V: 48 = 12 / (1 − D) → 1 − D = 0.25 → D = 0.75

  3. Inductor ripple in the buck converter at 100 kHz with L = 47 µH: ΔI = (V_in − V_o) × D / (f × L) = (48 − 12) × 0.25 / (100,000 × 47 × 10⁻⁶) = 9 / 4.7 ≈ 1.91 A

Chopper Classes for DC Motors

  • Class A: one-quadrant (motoring only).

  • Class B: regenerative braking.

  • Class C, D, E: two- and four-quadrant operation (forward/reverse, motoring/braking).

Applications

  • Laptop and phone chargers (isolated converters), point-of-load converters on circuit boards.

  • Solar MPPT charge controllers.

  • EV DC-DC converters (high-voltage battery to 12 V auxiliary).

  • Battery-operated vehicles and e-rickshaws.

  • LED drivers and DC motor speed control.

68

What is a UPS, and how is it different from an inverter?

A UPS (uninterruptible power supply) provides continuous, conditioned power to critical loads such as computers, servers and medical equipment, switching to battery with zero or a few milliseconds of transfer time when the mains fails. A home inverter also supplies AC from batteries during outages, but it is designed for longer backup of household loads and typically has a longer changeover time (often about 10–20 ms or more) and less power conditioning.

Read full answer

Applies toElectrical engineering (power electronics and power quality)

Types of UPS

Type Operation Transfer time Use
Offline (standby) Load on mains; switches to inverter on failure About 5–12 ms Single PCs, small loads
Line-interactive Mains with automatic voltage regulation (AVR); inverter on failure About 2–6 ms Small offices, networking
Online (double conversion) Mains → rectifier → DC bus → inverter → load continuously Zero Servers, data centres, hospitals, industry

UPS vs Inverter

Aspect UPS Home inverter
Purpose Protect critical equipment, ride through outages Backup for household loads
Transfer time Zero (online) to a few ms About 10–20 ms or more
Power conditioning Voltage regulation, surge and noise filtering (especially online) Limited
Backup time Usually minutes (to shut down safely or wait for a generator) Hours
Battery Smaller (often sealed VRLA or lithium) Larger tubular lead-acid
Output waveform Pure sine (online and good line-interactive) Pure or modified sine
Cost per VA Higher Lower

Worked Example: Sizing a UPS

Answer: a 5 kVA online UPS, needing about 1.6 kWh of usable battery for 30 minutes. The loads are 10 computers at 150 W and 2 servers at 400 W, with PF 0.8 and 25% margin.

  1. Load = 10 × 150 + 2 × 400 = 2,300 W

  2. VA = 2,300 / 0.8 = 2,875 VA; with 25% margin ≈ 3,594 VA → choose 5 kVA (next standard size)

  3. Battery energy for 30 minutes at 90% inverter efficiency = 2,300 × 0.5 / 0.9 ≈ 1,278 Wh

  4. At 80% usable capacity → about 1,600 Wh of battery (e.g. 8 × 12 V batteries of about 17 Ah or more; choose higher Ah because capacity falls at high discharge rates)

Choosing

  • Servers, network equipment, medical and lab instruments: online UPS.

  • Desktop PC: offline or line-interactive.

  • Fans, lights, TV for long power cuts: home inverter.

69

What is a control system? How do open-loop and closed-loop systems differ?

A control system is an arrangement of components that manages, commands or regulates the behaviour of other devices or processes to achieve a desired output. In an open-loop system, the control action does not depend on the output (there is no feedback), so it cannot correct errors. In a closed-loop (feedback) system, the output is measured and compared with the desired value (setpoint), and the error is used to adjust the control action automatically.

Read full answer

Applies toElectrical engineering (control systems)

Comparison

Aspect Open-loop Closed-loop
Feedback None Yes (sensor measures output)
Accuracy Depends on calibration High; corrects disturbances
Response to disturbances Cannot correct Corrects automatically
Stability Generally stable Can become unstable if poorly designed
Complexity and cost Simple, cheap More complex, costlier
Sensitivity to parameter changes High Low
Examples Washing machine timer, traffic lights on fixed timing, toaster, electric kettle without thermostat Air conditioner with thermostat, cruise control, voltage regulators (AVR), autopilot, DC motor speed control

Block Diagram (Closed Loop)

Setpoint → comparator (error = setpoint − feedback) → controller → actuator → plant (process) → output → sensor → back to comparator.

Closed-loop transfer function (negative feedback): T(s) = G(s) / (1 + G(s)·H(s))

Worked Example: Effect of Feedback

Answer: the closed-loop output changes only about 0.11% for a 10% gain change. A unity-feedback system has forward gain K = 99.

  1. Closed-loop gain = 99 / (1 + 99) = 0.99; steady-state error = 1 / (1 + 99) = 1%

  2. If K drops by 10% to 89.1: closed-loop gain = 89.1 / 90.1 ≈ 0.9889

  3. Change = (0.99 − 0.9889) / 0.99 ≈ 0.11%

An open-loop system with the same 10% gain drop would see a 10% change in output.

Advantages of Feedback

  • Reduces sensitivity to parameter variations and disturbances.

  • Improves accuracy and speed of response.

  • Can stabilise naturally unstable processes.

Drawbacks

  • Needs sensors and more components.

  • Excessive gain causes oscillation or instability; design uses stability tools (Routh-Hurwitz, root locus, Bode and Nyquist plots).

70

What is a transfer function?

A transfer function is the ratio of the Laplace transform of the output of a linear time-invariant (LTI) system to the Laplace transform of its input, assuming all initial conditions are zero: G(s) = Y(s) / X(s). It describes how a system responds to inputs and is the basis for analysing stability, transient response and frequency response in control systems.

Read full answer

Applies toElectrical engineering (control systems)

Key Terms

  • Poles: values of s that make the denominator zero; they decide stability and the natural response.

  • Zeros: values of s that make the numerator zero.

  • Order: highest power of s in the denominator.

  • Characteristic equation: denominator = 0.

  • Stability: all poles must lie in the left half of the s-plane (negative real parts).

Worked Example 1: RC Low-Pass Filter

Answer: G(s) = 1 / (1 + 0.001s), with a pole at s = −1,000 and a cut-off of about 159 Hz. R = 1 kΩ, C = 1 µF, input across R and C in series, output across C.

  1. G(s) = (1/sC) / (R + 1/sC) = 1 / (1 + sRC)

  2. RC = 1,000 × 1 × 10⁻⁶ = 0.001 s (τ = 1 ms)

  3. Pole at s = −1 / RC = −1,000 rad/s

  4. Cut-off frequency f_c = 1 / (2πRC) ≈ 159 Hz

  5. Step response: output reaches 63.2% of final value in 1 ms and about 99% in 5 ms

Worked Example 2: Second-Order System

Answer: ω_n = 10 rad/s, ζ = 0.5 and overshoot ≈ 16.3%. G(s) = 100 / (s² + 10s + 100).

  1. Compare with ω_n² / (s² + 2ζω_n·s + ω_n²): ω_n² = 100 → ω_n = 10 rad/s

  2. 2ζω_n = 10 → ζ = 0.5 (underdamped)

  3. Maximum overshoot = e^(−πζ/√(1−ζ²)) = e^(−1.814) ≈ 16.3%

  4. Settling time (2% criterion) ≈ 4 / (ζω_n) = 4 / 5 = 0.8 s

Uses

  • Block diagram reduction (series multiply, parallel add, feedback formula).

  • Stability analysis (Routh-Hurwitz, root locus).

  • Frequency response (substitute s = jω for Bode and Nyquist plots).

  • Controller design (PID tuning, compensators).

Limitations

Applies only to linear time-invariant systems with zero initial conditions; non-linear systems (saturation, friction) need linearisation or state-space and non-linear methods.

71

What is a PID controller?

A PID controller is a feedback controller that calculates its output from three terms based on the error (e = setpoint − measured value): Proportional (P), which reacts to the present error; Integral (I), which acts on the accumulated past error to remove steady-state error; and Derivative (D), which reacts to the rate of change of error to anticipate the future and damp overshoot. It is the most widely used controller in industry.

Read full answer

Applies toElectrical engineering (control systems and automation)

Equation

u(t) = K_p·e(t) + K_i·∫e(t)dt + K_d·de(t)/dt

or in Laplace form: C(s) = K_p + K_i/s + K_d·s, with K_i = K_p / T_i and K_d = K_p·T_d.

Effect of Each Term

Term Effect Too much
P Faster response, reduces (but does not remove) steady-state error Oscillation, overshoot
I Removes steady-state error Overshoot, slow oscillation, integral windup
D Reduces overshoot, improves stability Amplifies noise

Worked Example 1: Controller Output

Answer: output = 29.8%. A temperature controller has K_p = 2, K_i = 0.5 s⁻¹ and K_d = 0.1 s. The current error is 10 °C, accumulated error is 20 °C·s, and the error is falling at 2 °C/s.

  • P term = 2 × 10 = 20

  • I term = 0.5 × 20 = 10

  • D term = 0.1 × (−2) = −0.2

  • Output = 20 + 10 − 0.2 = 29.8% (e.g. heater power)

Worked Example 2: Ziegler–Nichols Tuning

Answer: K_p = 6, K_i = 3 s⁻¹, K_d = 3 s. In a closed-loop test, the ultimate gain K_u = 10 and the oscillation period T_u = 4 s.

  • K_p = 0.6 × 10 = 6

  • T_i = T_u / 2 = 2 s → K_i = 6 / 2 = 3 s⁻¹

  • T_d = T_u / 8 = 0.5 s → K_d = 6 × 0.5 = 3 s

These are starting values; fine-tune on the real process.

Practical Issues

  • Integral windup: when the actuator saturates, the integral keeps growing; anti-windup clamps it.

  • Derivative kick: use derivative on the measurement rather than the error.

  • Filtering: low-pass filter on the D term to limit noise.

  • Many loops use only PI (flow, pressure) or P (level, where offset is acceptable).

Applications

Temperature control (ovens, HVAC), motor speed and position control, pressure and flow loops in process plants, voltage regulators, drones and robotics. PID blocks are built into PLCs, DCS, VFDs and temperature controllers.

72

What is the difference between a PLC and a microcontroller?

A PLC (programmable logic controller) is a rugged industrial computer built to control machines and processes reliably in harsh environments. It has standard industrial I/O (24 V DC, 230 V AC, 4–20 mA), is programmed in IEC 61131-3 languages such as ladder logic, and can be maintained by electricians and technicians. A microcontroller is a single chip containing a CPU, memory and peripherals, embedded inside a product (appliances, devices, vehicles). It is programmed in C/C++ or assembly by electronics engineers and needs a custom circuit board around it.

Read full answer

Applies toElectrical engineering (automation and embedded systems)

Comparison

Aspect PLC Microcontroller
Form Complete unit (CPU, power supply, I/O modules) Single IC on a custom PCB
Environment Industrial: noise, vibration, temperature, surges Depends on product design
I/O Standard industrial levels, isolated, modular Logic levels (3.3/5 V), needs interface circuits
Programming Ladder, FBD, ST, SFC, IL (IEC 61131-3) C, C++, assembly, MicroPython
Who programs Automation engineers, technicians Embedded/electronics engineers
Modification Easy online edits, monitoring Re-flash firmware
Communication Profinet, EtherNet/IP, Modbus, Profibus UART, SPI, I2C, CAN, custom
Cost High per unit Very low per unit at volume
Reliability and support Long-term vendor support, certified Depends on design
Typical use Factory automation, packaging lines, water plants, conveyors Washing machines, remotes, IoT devices, automotive ECUs

PLC Scan Cycle

  1. Read inputs (input image).

  2. Execute program.

  3. Update outputs.

  4. Housekeeping and communication.

Worked Example: Scan Time and Fast Signals

Answer: the pulse may be missed; use a high-speed counter or interrupt input. A PLC has a scan time of 10 ms, and a sensor produces 5 ms pulses.

  • A pulse shorter than the scan time can start and end between two input reads, so ordinary inputs may miss it.

  • Rule of thumb: a signal should last at least about two scan times (here 20 ms) to be read reliably on a normal input.

  • Fix: use a high-speed counter module, interrupt inputs, or a faster PLC or task.

Example: Motor Start/Stop in Ladder Logic

A start push button (NO) in series with a stop push button (wired NC) drives the motor coil; a holding (seal-in) contact of the motor output is placed in parallel with the start button, so the motor keeps running after the start button is released, until stop is pressed or the overload trips.

Choosing

  • PLC: industrial machines, low-volume custom automation, safety-critical processes needing maintainability.

  • Microcontroller: mass-produced products where cost and size matter.

73

What is a multimeter, and what can it measure?

A multimeter is a test instrument that combines several measurement functions in one device. A typical digital multimeter (DMM) measures AC and DC voltage, AC and DC current, resistance, continuity and diode forward voltage, and many models also measure capacitance, frequency, temperature and duty cycle. It is the most basic tool for testing, installing and troubleshooting electrical and electronic circuits.

Read full answer

Applies toElectrical engineering (measurements and instrumentation)

Functions and How to Measure

Quantity How to connect Notes
Voltage (V) In parallel across the component or supply High input impedance (about 10 MΩ)
Current (A) In series, breaking the circuit; move the lead to the A or mA jack Fused; never put an ammeter across a supply
Resistance (Ω) Across the component, with power off Disconnect one end for accurate in-circuit readings
Continuity Across the conductor, power off Beeps for low resistance
Diode test Across the diode Shows forward voltage (about 0.5–0.7 V for silicon)
Capacitance Across a discharged capacitor Discharge first
Frequency In parallel Useful for VFD output, signals

Clamp meters measure current without breaking the circuit, using a clamp around one conductor.

Worked Example: Reading Accuracy

Answer: the true voltage lies within about 227.4–232.6 V. A 6,000-count meter on its 600 V AC range reads 230.0 V, with a specified accuracy of ±(1.0% of reading + 3 counts).

  • Resolution on this range = 0.1 V, so 3 counts = 0.3 V

  • Error = 1.0% × 230.0 + 0.3 = 2.3 + 0.3 = ±2.6 V

  • Range = 227.4 V to 232.6 V

True RMS

Average-responding meters read correctly only for pure sine waves. For distorted waveforms (VFD outputs, SMPS, LED drivers), use a True RMS meter.

Safety Ratings (IEC 61010)

Category Where
CAT II Plug-in appliances, socket outlets
CAT III Distribution boards, building wiring, fixed equipment
CAT IV Supply origin: service entrance, meters, overhead lines

Choose a meter rated for the highest category and voltage you will measure (e.g. CAT III 600 V or CAT IV 600 V for panel work).

Safe Use

  • Check the meter on a known live source before and after testing (prove-test-prove).

  • Set the function and range before connecting; never measure voltage with leads in the current jack.

  • Use leads with shrouded probes and finger guards; replace damaged leads.

74

What is a megger, and what is insulation resistance testing?

A megger (insulation resistance tester) is an instrument that applies a high DC test voltage (typically 500 V, 1 kV, 2.5 kV or 5 kV) to measure the insulation resistance between conductors, or between conductors and earth, in megaohms (MΩ) or gigaohms (GΩ). Insulation resistance testing checks the condition of cables, motors, transformers and wiring, detecting moisture, contamination, ageing and damage before they cause faults.

Read full answer

Applies toElectrical engineering (testing and maintenance)

Typical Test Voltages

Equipment rated voltage Test voltage
Up to 250 V (domestic wiring) 250–500 V DC
415 V systems, LV motors and cables 500 V or 1,000 V DC
3.3–6.6 kV equipment 2.5 kV DC
11 kV and above 5 kV (or 10 kV) DC

How to Test

  1. Isolate the equipment, lock out and prove it dead.

  2. Disconnect sensitive electronics (VFDs, surge protectors, meters).

  3. Discharge capacitive equipment and cables.

  4. Connect the megger: line terminal to the conductor, earth terminal to the frame or earth (guard terminal to reduce surface leakage on high-value tests).

  5. Apply voltage for the set time (often 1 minute) and record the reading and temperature.

  6. Discharge the equipment after the test.

Acceptance Values (Guidelines)

  • Common rule of thumb: at least 1 MΩ per kV of rating + 1 MΩ (older guideline).

  • IEEE 43: at least 5 MΩ for random-wound machines below 1 kV and 100 MΩ for most form-wound machines, at 40 °C.

  • LV installations (IEC 60364-6): at least 1 MΩ at 500 V test voltage for circuits up to 500 V.

  • Readings should be compared with past records; a falling trend matters more than one value.

Worked Example: Polarisation Index

Answer: PI = 3.0, which indicates good, dry insulation. A 415 V motor reads 150 MΩ after 1 minute and 450 MΩ after 10 minutes at 1 kV.

PI = R₁₀ / R₁ = 450 / 150 = 3.0

PI Insulation condition
Below 1.0 Dangerous
1.0–2.0 Questionable (moisture, dirt)
2.0–4.0 Good
Above 4.0 Excellent

DAR (dielectric absorption ratio) = R₆₀ₛ / R₃₀ₛ; above about 1.25–1.6 is generally acceptable.

Factors Affecting Readings

  • Temperature: IR roughly halves for every 10 °C rise, so correct readings to a reference temperature (e.g. 40 °C).

  • Humidity and surface dirt: reduce readings.

  • Cable length: longer cables give lower IR.

75

What are a CT and a PT?

A CT (current transformer) and a PT (potential transformer, also called VT, voltage transformer) are instrument transformers that step down high currents and voltages to standard, safe levels (typically 1 A or 5 A for CTs and 110 V for PTs) for meters, relays and control equipment. They also isolate instruments from the high-voltage system.

Read full answer

Applies toElectrical engineering (measurements and protection)

Comparison

Aspect CT PT (VT)
Measures Current Voltage
Connection Primary in series with the line Primary in parallel (across the line or phase to earth)
Secondary rating 1 A or 5 A 110 V (or 110/√3 V)
Primary Few turns (often a single bar) Many turns
Load (burden) Low impedance (ammeters, current coils) High impedance (voltmeters, voltage coils)
Safety rule Never open-circuit the secondary while primary carries current Never short-circuit the secondary
Accuracy classes Metering: 0.2, 0.5, 0.2S, 0.5S; protection: 5P10, 5P20, PS Metering: 0.2, 0.5, 1.0; protection: 3P, 6P

Why a CT Secondary Must Never Be Open

The primary current is fixed by the line. With the secondary open, there are no opposing ampere-turns, so all primary current magnetises the core: the core saturates, dangerously high voltages (kV) appear at the secondary terminals, and the core overheats. Always short the secondary (using shorting links) before removing a meter or relay.

Worked Example

Answer: primary current 256 A, voltage 10.8 kV, and meter multiplying factor 8,000. An ammeter on a 400/5 A CT reads 3.2 A, and a voltmeter on an 11,000/110 V PT reads 108 V.

  1. CT ratio = 400 / 5 = 80 → primary current = 3.2 × 80 = 256 A

  2. PT ratio = 11,000 / 110 = 100 → primary voltage = 108 × 100 = 10,800 V (10.8 kV)

  3. Energy meter multiplying factor (MF) = CT ratio × PT ratio = 80 × 100 = 8,000, so a meter advance of 2.5 units means 2.5 × 8,000 = 20,000 kWh

Key Terms

  • Burden: load on the secondary in VA (e.g. 15 VA), including leads.

  • Knee-point voltage: for protection CTs (class PS), where the core starts to saturate.

  • 5P20: 5% composite error at 20 times rated current.

  • CVT (capacitive voltage transformer): used at 132 kV and above; also couples PLCC signals.

76

How is electrical energy measured, and what is a unit (kWh)?

Electrical energy is measured by an energy meter, which continuously multiplies voltage, current and power factor and adds up the result over time. The billing unit is the kilowatt-hour (kWh), called one “unit” in India: the energy used by a 1 kW load running for 1 hour. 1 kWh = 1,000 W × 3,600 s = 3.6 MJ.

Read full answer

Applies toElectrical engineering (measurements and utilisation)

Formula

Energy (kWh) = Power (kW) × Time (hours)

For several appliances: total units = Σ (power in kW × hours used).

Worked Example: Monthly Household Consumption

Answer: about 283.5 units per month.

Appliance Power Hours/day kWh/day
5 LED bulbs 10 W each (50 W) 6 0.30
Ceiling fan 75 W 10 0.75
Refrigerator (rated about 1.2 kWh/day) 24 (cycling) 1.20
Air conditioner 1.2 kW average 6 7.20
Total 9.45

Monthly = 9.45 × 30 = 283.5 units. The AC alone accounts for about 76% of this.

Types of Energy Meters

Type Features
Electromechanical (induction disc) Rotating aluminium disc; older, being replaced
Static (electronic) Digital measurement, LED pulses, higher accuracy, tamper detection
Smart meter Two-way communication, remote reading, time-of-day tariffs, prepaid options (being rolled out across India under RDSS)
Net meter Records import and export for rooftop solar consumers

Meter Constant

Electronic meters blink an LED at a rate set by the meter constant (e.g. 3,200 impulses/kWh). A 1 kW load gives 3,200 pulses per hour ≈ 53.3 pulses per minute. Counting pulses against a known load checks meter accuracy.

Related Quantities

  • kVAh: apparent energy (some tariffs bill in kVAh, which includes the effect of power factor).

  • kVARh: reactive energy.

  • Maximum demand (kW or kVA): highest average demand over a set interval (usually 15 or 30 minutes), billed for commercial and industrial consumers.

Saving Energy

Use BEE star-rated appliances, LED lighting, BLDC fans, inverter ACs set at 24–26 °C, and switch off standby loads.

77

What is the monthly bill for a 2 kW heater used 3 h daily?

Answer: the heater consumes 180 units (kWh), and the bill is ₹1,260 (energy charge only, at ₹7 per unit).

Read full answer

Applies toElectrical engineering (energy calculation)

Step-by-Step Calculation

  1. Daily energy = power × hours = 2 kW × 3 h = 6 kWh

  2. Monthly energy = 6 kWh × 30 days = 180 kWh = 180 units

  3. Bill = 180 units × ₹7 per unit = ₹1,260

Supporting Values

  • Current drawn on 230 V: I = 2,000 / 230 ≈ 8.7 A, so a 10 A or 16 A circuit with suitable cable is needed (a 16 A socket is normal for heaters).

  • Resistance of the element: R = V² / P = 230² / 2,000 ≈ 26.5 Ω (hot).

  • Energy in joules: 180 kWh × 3.6 MJ = 648 MJ.

Real Bill Considerations

Actual electricity bills in India usually include: - Slab (telescopic) tariffs: rates rise with consumption, so the marginal rate may differ from ₹7. - Fixed or demand charges per kW of sanctioned load. - Electricity duty and other state charges. - Fuel and power purchase cost adjustment charges.

So ₹1,260 is the energy charge for this appliance, not necessarily the total bill increase.

Ways to Reduce This Cost

  • Use a thermostat so the heater cycles instead of running continuously; if it runs only 60% of the time, consumption falls to 108 units (₹756).

  • Use an oil-filled radiator with thermostat or insulate the room.

  • For water heating, a heat pump water heater or solar water heater uses far less electricity than a resistance heater (heat pumps typically need about one-third of the energy).

Interview Tip

Write the formula, show units at each step (kW × h = kWh), and state the result clearly. Mentioning slab tariffs and fixed charges shows awareness of real billing.

78

What is a solar PV system? What are on-grid and off-grid systems?

A solar PV (photovoltaic) system converts sunlight directly into DC electricity using solar panels, and an inverter converts it to AC for use. An on-grid (grid-tied) system works together with the utility grid: it supplies the building and exports surplus power through a net or gross meter, but it shuts down during a grid outage (anti-islanding). An off-grid system is independent of the grid and stores energy in batteries for use at night and on cloudy days. Hybrid systems combine grid connection with battery backup.

Read full answer

Applies toElectrical engineering (renewable energy)

Components

  • Solar modules (mono PERC, TOPCon or bifacial panels, typically 400–600 Wp each).

  • Inverter: string or micro-inverter (on-grid), off-grid inverter with charge controller, or hybrid inverter.

  • Mounting structure, DC and AC cables, DC and AC distribution boxes with SPDs and fuses.

  • Batteries (off-grid and hybrid): lead-acid or lithium (LFP).

  • Net meter (on-grid).

  • Earthing and lightning protection.

Comparison

Aspect On-grid Off-grid Hybrid
Grid connection Yes No Yes
Batteries No Yes Yes
Works during power cuts No (anti-islanding) Yes Yes (backed-up loads)
Cost Lowest Highest High
Excess energy Exported to grid (net metering) Wasted when batteries are full Stored, then exported
Best for Cities with reliable grid Remote areas without grid Areas with frequent outages

Worked Example: Rooftop System

Answer: about 360 units a month, saving about ₹2,520 a month. A 3 kWp on-grid rooftop system (6 panels of 540 Wp ≈ 3.24 kWp) in a location with a specific yield of about 4 kWh per kWp per day, with electricity at ₹7 per unit.

  1. Daily generation ≈ 3 × 4 = 12 kWh

  2. Monthly ≈ 12 × 30 = 360 units

  3. Savings ≈ 360 × 7 = ₹2,520 per month (about ₹30,000 a year)

  4. Roof area needed ≈ about 6–8 m² per kWp → about 20–25 m²

Under the PM Surya Ghar Muft Bijli Yojana, residential consumers have been eligible for central financial assistance (around ₹30,000 per kW for the first 2 kW and ₹18,000 for the third kW, capped at ₹78,000); check the current scheme rules.

Performance Factors

Orientation (south-facing in India), tilt (roughly equal to latitude), shading, dust (regular cleaning), temperature (output falls about 0.3–0.4% per °C above 25 °C), and inverter efficiency.

79

What safety precautions should you take when working on electrical equipment?

When working on electrical equipment, the core rule is to treat every conductor as live until you have proved it dead. Key precautions are: isolate the supply, lock out and tag out (LOTO), test for absence of voltage, earth where needed, use proper PPE and insulated tools, keep safe clearances, and follow a permit-to-work system, as required by the CEA (Measures relating to Safety and Electric Supply) Regulations and good practice.

Read full answer

Applies toElectrical engineering (electrical safety)

Before Starting Work

  1. Plan the job: identify hazards, get a permit to work for HV or critical equipment.

  2. Isolate all sources (including backup supplies, DG sets, UPS, solar, capacitors).

  3. Lock out and tag out the isolating devices so they cannot be switched on.

  4. Prove dead: test with an approved voltage detector, checking it on a known live source before and after (prove-test-prove).

  5. Discharge and earth: discharge capacitors and cables; apply portable earths on HV equipment.

  6. Barricade the area and display warning signs.

During Work

  • Use PPE: insulated gloves (rated for the voltage), safety shoes, arc-rated clothing and face shield where arc flash risk exists, safety helmet, goggles.

  • Use insulated tools (1,000 V rated) and rubber mats.

  • Keep one hand away from earthed parts where possible; remove rings, watches and metal objects.

  • Never work alone on live or HV systems; have a trained person nearby.

  • Do not bypass interlocks, fuses or protective devices.

Worked Example: Why Small Currents Kill

Answer: about 230 mA flows through wet skin, which can be fatal, versus about 2.3 mA through dry skin. A person touches 230 V with body resistance of about 1,000 Ω (wet skin) or about 100 kΩ (dry skin).

  • Wet: I = 230 / 1,000 = 230 mA

  • Dry: I = 230 / 100,000 = 2.3 mA

Current (50 Hz, hand to hand/foot) Typical effect
About 1 mA Threshold of feeling
About 10 mA Pain, may be unable to let go
About 30 mA Breathing difficulty; RCD protection level
50–100 mA and above Ventricular fibrillation possible, often fatal

After Work

  • Remove tools, earths and locks only after everyone is clear; restore supply in a controlled way.

  • Return the permit and record the work.

Emergency Response

  • Do not touch a person in contact with a live conductor; switch off the supply or separate them with dry insulating material.

  • Call for medical help, give CPR if trained, and treat burns.

  • Report every incident and near miss.

80

What is the difference between a neutral wire and an earth wire?

The neutral wire is a current-carrying conductor that completes the circuit: it carries the return current from the load back to the source (the transformer’s star point) during normal operation. The earth (protective earth) wire normally carries no current; it connects the metal bodies of appliances to earth and only carries current during a fault, so that protective devices trip and people are protected from shock.

Read full answer

Applies toElectrical engineering (building wiring and safety)

Comparison

Aspect Neutral Earth (protective conductor)
Purpose Return path for normal load current Safety path for fault current
Current in normal operation Yes (equal to phase current in single-phase circuits) No (only small leakage)
Connected to Transformer star point (earthed at the source) Earth electrode and metal parts of equipment
Colour (IS 732 / IEC) Black (older practice) or blue Green or green-yellow
Switching Not fused separately; double-pole switches isolate both phase and neutral Never switched or fused
Voltage to earth Close to zero (a few volts due to drop and unbalance) Zero

Phase (line) wires are commonly red, yellow and blue (older), or brown, black and grey (harmonised colours).

Neutral-to-Earth Voltage

A small voltage between neutral and earth (typically under about 2–5 V) is normal because of current flowing in the neutral. Higher values point to loose neutral connections, overloaded neutrals or poor earthing, and can disturb sensitive electronics.

Worked Example: Danger of a Broken Neutral

Answer: the 1 kW load sees about 300 V and the 3 kW load only about 100 V. In a three-phase, four-wire supply, the common neutral breaks. Phase A supplies a 1 kW load and phase B a 3 kW load (both 230 V rated), and phase C is off. The two loads end up in series across the 400 V line voltage.

  1. R_A = 230² / 1,000 ≈ 52.9 Ω; R_B = 230² / 3,000 ≈ 17.6 Ω

  2. Current = 400 / (52.9 + 17.6) ≈ 5.67 A

  3. V_A = 5.67 × 52.9 ≈ 300 V (overvoltage, damages appliances); V_B = 5.67 × 17.6 ≈ 100 V

This is why neutral connections must be sound, and why voltage-sensitive equipment may be protected by over-voltage relays.

Why Earth and Neutral Must Not Be Swapped or Combined at the Consumer End

  • Using the earth as a return path makes the earth conductor and appliance bodies carry current, which can make them live.

  • RCCBs would trip (phase and neutral currents unequal) or be bypassed.

  • Neutral and earth are bonded only at the source (or as specified in TN-C-S systems), never randomly in the installation.

Sign in to keep reading

You've opened 2 full answers. Sign in to read all 80 Electrical Engineering answers, mark what you know and pick up where you left off.

Report a mistake

What's wrong?

All Core Engineering subjects