Skip to content

Strength of Materials MCQ Questions

0
Answered
0
Correct
0%
Accuracy
Q101 Easy

The unit of work or energy in S.I. units is

Newton
Pascal
Kilogram meter
Joule
Q102 Easy

Which one of the following statements is not correct?

The tangent of the angle of friction is equal to coefficient of friction
The angle of repose is equal to angle of friction
The tangent of the angle of repose is equal to coefficient of friction
The sine of the angle of repose is equal to coefficient to friction
Q103 Easy

Poisson’s ratio is defined as the ratio of

Longitudinal stress and longitudinal strain
Longitudinal stress and lateral stress
Lateral stress and longitudinal stress
Lateral stress and lateral strain
Q104 Easy

If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called

Chain riveting
Zig-zag riveting
Diamond riveting
None of these
Q105 Easy

The angle which an inclined plane makes with the horizontal when a body placed on it is about to move down is known as angle of

Friction
Limiting friction
Repose
Kinematic friction
Q106 Easy

If the length of a cantilever carrying an isolated load at its free end is doubled, the deflection of the free end will increase by

8
1/8
1/3
2
Q107 Easy

What is the term for the line or region of zero stress between the two surfaces?

Neutral axis
Interface
Interface line
Perpendicular
Q108 Easy

Hooke’s law holds good up to

Yield point
Limit of proportionality
Breaking point
Elastic limit
Q109 Easy

The G. of a plane lamina will not be at its geometrical centre in the case of a

Right angled triangle
Equilateral triangle
Square
Circle
Q110 Easy

The total strain energy stored in a body is termed as

Resilience
Proof resilience
Modulus of resilience
Toughness
Q111 Easy

The units of moment of inertia of an area are

Kg m²
M4
Kg/m²
M3
Q112 Easy

What type of force is needed to permanently deform the material after removing the load?

Chemical
Nuclear
Inertial
Elastic
Q113 Easy

The law which states, "Within elastic limits strain produced is proportional to the stress producing it", is known as

Bernoulli's law
Stress law
Hooke's law
Poisson's law
Q114 Easy

The bending moment is maximum on a section where shearing force

Is maximum
Is minimum
Is equal
Changes sign
Q115 Easy

The Young’s modulus of a wire is defined as the stress which will increase the length of wire compared to its original length

Half
Same amount
Double
One-fourth
Q116 Easy

If rain is falling in the opposite direction of the movement of a pedestrain, he has to hold his umbrella

More inclined when moving
Less inclined when moving
More inclined when standing
Less inclined when standing
Q117 Easy

The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to

R
1/r
R2
1/r²
Q118 Easy

At either end of a plane frame, maximum number of possible bending moments, are

Zero
One
Two
Three
Q119 Easy

If two forces acting at a joint are not along the straight line, then for the equilibrium of the joint

One of the forces must be zero
Each force must be zero
Forces must be equal and of the same sign
Forces must be equal in magnitude but opposite in sign
Q120 Easy

The rectangular beam 'A' has length l, width b and depth d. Another beam 'B' has the same length and depth but width is double that of 'A'. The elastic strength of beam 'B' will be __________ as compared to beam A.

Same
Double
Six times
Four times
Q121 Easy

If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is given by

(b + d)/b
(b - d)/b
(d - b)/d
(b - d)/d
Q122 Easy

What is the maximum stress to which a specimen may be subjected and still return to its original length upon release of the load?

Shear stress
Damage limit
Fracture
Elastic limit
Q123 Easy

A rectangular bar of width b and height h is being used as a cantilever. The loading is in a plane parallel to the side b. The section modulus is

Bh3
/12
Bh²/6
B²h/6
Q124 Easy

Which of the following is not a scalar quantity?

Time
Mass
Volume
Acceleration
Q125 Easy

Strain energy of any member may be defined as work done on it

To deform it
To resist elongation
To resist shortening
All the above
Q126 Easy

What is the formula for transverse strain?

Transverse Strain = Change in longitudinal dimension/Longitudinal dimension
Transverse Strain = Change in transverse dimension/Longitudinal dimension
Transverse Strain = Change in transverse dimension/Transverse dimension
Transverse Strain = Change in longitudinal dimension/Transverse dimension
Q127 Easy

Kinetic friction is the

Tangent of angle between normal reaction and the resultant of normal reaction and the limiting friction
Ratio of limiting friction and normal reaction
The friction force acting when the body is just about to move
The friction force acting when the body is in motion
Q128 Easy

The property of a material by which it can be beaten or rolled into thin plates, is called

Malleability
Ductility
Plasticity
Elasticity
Q129 Easy

The equivalent length of a column fixed at both ends, is

0.5 l
0.7 l
L
1.5 l
Q130 Easy

The forces, which meet at one point, but their lines of action do not lie in a plane, are called

Coplanar non-concurrent forces
Non-coplanar concurrent forces
Non-coplanar non-concurrent forces
Intersecting forces
Q131 Easy

The slenderness ratio of a vertical column of a square cross-section of 2.5 cm sides and 300 cm length, is

200
240
360
416
Q132 Easy

In a continuous bending moment curve the point where it changes sign, is called

Point of inflexion
Point of contraflexure
Point of virtual hinge
All the above
Q133 Easy

If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either

Meet in a point
Be all parallel
At least two of them must meet
All the above are correct
Q134 Easy

A force in tension will cause the member to ___________.

Remain the same length
Increase its length
Decrease its length
Reverse its length
Q135 Easy

What term is used to describe the point on a stress-strain curve at which it begins to deviate from the straight-line relationship between stress and strain?

Critical stress
Maximum stress
Hysteresis
Proportional limit
Q136 Easy

A number of forces acting at a point will be in equilibrium if

Their total sum is zero
Two resolved parts in two directions at right angles are equal
Sum of resolved parts in any two perpendicular directions are both zero
All of them are inclined equally
Q137 Easy

The stiffness factor for a prismatic beam of length L and moment of inertia I, is

IE/L
2EI/L
3EI/L
4EI/L
Q138 Easy

Limiting force of friction is the

Tangent of angle between normal-reaction and the resultant of normal reaction and limiting friction
Ratio of limiting friction and normal reaction
The friction force acting when the body is just about to move
The friction force acting when the body is in motion
Q139 Easy

A pair of smith’s tongs is an example of the lever of

Zeioth order
First order
Second order
Third order
Q140 Easy

The maximum twisting moment a shaft can resist, is the product of the permissible shear stress and

Moment of inertia
Polar moment of inertia
Polar modulus
Modulus of rigidly
Q141 Easy

A flywheel on a motor goes from rest to 1000 rpm in 6 sec. The number of revolutions made is nearly equal to

25
50
100
250
Q142 Easy

When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as

Lap joint
Butt joint
Single riveted single cover butt joint
Double riveted double cover butt joint
Q143 Easy

For a cantilever with a uniformly distributed load W over its entire length L, the maximum bending moment is

WL
½ WL
WL
½ WL2
Q144 Easy

The phenomenon of slow extension of materials having constant load, i.e. increasing with the time is called

Creeping
Yielding
Breaking
None of these
Q145 Easy

In a loaded beam, the point of contraflexure occurs at a section where

Bending moment is minimum
Bending moment is zero or changes sign
Bending moment is maximum
Shearing force is maximum
Q146 Easy

What does the term "neutral axis" mean?

Equal stress for all runs
Equal stress on all axes
Zero stress
Q147 Easy

What is Torsion?

The twisting of an object due to an applied force.
The twisting of an object due to an applied pressure.
The twisting of an object due to an applied torque.
The twisting of an object due to an applied weight.
Q148 Easy

On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be

Downwards at its upper end
Upwards at its upper end
Perpendicular to the wall at its upper end
Zero at its upper end
Q149 Easy

If the radius of wire stretched by a load is doubled, then its Young’s modulus will be

Doubled
Halved
Become four times
Remain unaffecte
Q150 Easy

A column that fails due to direct stress, is called

Short column
Medium column
Weak column
Long column
Showing 150 of 360 questions

Teachers: using these Strength of Materials questions with a class? Tell us about your class.

Report a mistake

What's wrong?