What is the ability of a material to return to its previous shape after stress is released called?
The maximum frictional force which comes into play when a body just begins to slide over another surface is called
If rain is falling in the opposite direction of the movement of a pedestrian, he has to hold his umbrella
Stress in members of statically determinate simple frames, can be determined by
The unit of Young’s modulus is
When a rectangular beam is loaded transversely, the maximum compressive stress is developed on the
If a part is constrained to move and heated, it will develop
The co-efficient of friction depends upon
What does the term yield strength refer to?
When a rectangular beam is loaded transversely, the maximum compressive stress develops on
Pick up the incorrect statement
The algebraic sum of moments of the forces forming couple about any point in their plane is
What is Axial Strain?
The ratio of direct stress to volumetric strain in case of a body subjected to three mutually perpendicular stresses of equal intensity, is equal to
A beam overhangs its support, and point E is the free end of the overhang, with no load or moment applied at E. What is the bending moment at E?
A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is
A member which does not regain its original shape after removed of load producing deformation is said
Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose
The value of modulus of elasticity for mild steel is of the order of
A bending moment may be defined as:
When two main plates are kept in alignment butting each other and riveted with cover plate on both sides of the main plates with two rows of rivets in each main plate, the joint is known as __________ double cover butt joint.
Which of the following is not the unit of distance?
Forces are called concurrent when their lines of action meet in
The radius of gyration of a rectangular section is not proportional to
A cantilever truss is attached to a wall at A (top) and B (bottom), with B 3 m directly below A. It carries vertical loads of 10 tonnes at 3 m and 10 tonnes at 6 m from the wall. The support at B gives only a horizontal reaction. What is the horizontal component of the reaction at A?
The property of a material by which it can be drawn to a smaller section, due to tension, is called
What occurs when the design stress exceeds the material yield strength?
Which is the false statement about true stress-strain method
Flow stress corresponds to
A shaft turning 150 r.p.m. is subjected to a torque of 150 kgm. Horse power transmitted by the shaft is
Shear force for a cantilever carrying a uniformly distributed load over its length, is
When trying to turn a key into a lock, following is applied
Tangent of angle of friction is equal to
What is shear?
Which of the following is not the unit of work, energy and heat?
The ratio of the effective length of a column and minimum radius of gyration of its cross-sectional area, is known
Young’s modulus is defined as the ratio of
The stress necessary to initiate yielding, is considerably
Which of the following is the example of lever of first order
A beam of length L is pinned at both ends and is subjected to a concentrated bending couple of moment M at its centre. The maximum bending moment in the beam is
A projectile is fired at an angle 9 to the vertical. Its horizontal range will be maximum when 9 is
According to Hooke's law, within the elastic limit stress is ______ to strain.
A composite bar is made by bonding two materials, a and b, at 25°C. The coefficient of thermal expansion of a is greater than that of b. If the bar is heated to 45°C, then
The ultimate tensile stress of mild steel compared to ultimate compressive stress is
In a shaft shear stress intensity at a point is not
Struts are load carrying members of a frame structure which are subjected to
Modulus of rigidity is defined as the ratio of
In a tensile test on mild steel specimen, the breaking stress as compared to ultimate tensile stress is
If the rivets in adjacent rows are staggered and the outermost row has only one rivet, the arrangement of the rivets is called
It equal and opposite forces applied to a body tend to elongate it, the stress so produced is called
Teachers: using these Strength of Materials questions with a class? Tell us about your class.