Skip to content

Strength of Materials MCQ Questions

0
Answered
0
Correct
0%
Accuracy
Q301 Easy

Strain is defined as the ratio of the _____.

Static equilibrium
Deformation
Change in length per original length
Not applicable
Q302 Easy

A non-yielding support implies that the

Support is frictionless
Support can take any amount of reaction
Support holds member firmly
Slope of the beam at the support is zero
Q303 Easy

The neutral axis of the cross-section a beam is that axis at which the bending stress is

Maximum
Infinity
Minimum
Zero
Q304 Easy

Every material obeys the Hooke's law within its

Elastic limit
Plastic point
Limit of proportionality
None of these
Q305 Easy

What is the definition of toughness?

The ability of a metal to resist heat
The ability of a metal to resist electricity
The ability of a metal to resist corrosion
The ability of a metal to resist fracture
Q306 Easy

What does STRAIN represent?

The amount of force applied
The change in length per unit area
The ratio of the change in length per original length
The original length
Q307 Easy

The algebraic sum of the resolved parts of a number of forces in a given direction is equal to the resolved part of their resultant in the same direction. This is as per the principle of

Forces
Independence of forces
Dependence of forces
Resolution of forces
Q308 Easy

Which of the following is not the unit of pressure?

Kg/cm
Atm
Kg/cm²
Newton
Q309 Easy

The center of gravity of a triangle lies at the point of

Concurrence of the medians
Intersection of its altitudes
Intersection of bisector of angles
Intersection of diagonals
Q310 Easy

The phenomenon of slow growth of strain under a steady tensile stress, is called

Yielding
Creeping
Breaking
None of these
Q311 Easy

The thermal stress __________ upon the cross-sectional area of the bar.

Depends
Does not depend
Q312 Easy

If the depth of a simply supported beam carrying an isolated load at its centre, is doubled, the deflection of the beam at the centre will be changed by a factor of

2
1/2
8
1/8
Q313 Easy

The resultant of the following three couples 20 kg force, 0.5 m arm, +ve sense 30 kg force, 1 m arm, -ve sense 40 kg force, 0.25 m arm, +ve sense having arm of 0.5 m will be

20 kg, -ve sense
20 kg, +ve sense
10 kg, +ve sense
10 kg, -ve sense
Q314 Easy

The necessary condition for forces to be in equilibrium is that these should be

Coplanar
Meet at one point ;
Both and above
All be equal
Q315 Easy

A truss rests on a pin support at B. The vertical part of the reaction at B acts upward (north) and the horizontal part acts to the right (east). In which direction does the resultant reaction at B act?

East of North
West of North
East of South
West of South
Q316 Easy

A key is subjected to side pressure as well at shearing forces. These pressures are called

Bearing stresses
Fatigue stresses
Crushing stresses
Resultant stresses
Q317 Easy

Ties are load carrying members of a frame, which are subjected to

Transverse loads
Axial tension loads
Axial compressive loads
Torsional loads
Q318 Easy

The object of caulking in a riveted joint is to make the joint

Free from corrosion
Free from stresses
Stronger in tension
Leak-proof
Q319 Easy

What does it mean for a material to be stressed within the elastic region?

When the strain energy is greater than the elastic limit
When the working stress exceeds the elastic limit
When a permanent deformation occurs
When the working stress does not exceed the elastic limit
Q320 Easy

A material capable of absorbing large amount of energy before fracture is known as

Ductility
Toughness
Resilience
Shock proof
Q321 Easy

The energy absorbed in a body, when it is strained within the elastic limits, is known as

Strain energy
Resilience
Proof resilience
Modulus of resilience
Q322 Easy

In a beam, the neutral plane

May be its centre
Passes through the C.G. of the area of cross-section
Does not change during deformation
None of these
Q323 Easy

The equivalent length of a column fixed at one end and free at the other end, is

0.5 l
0.7 l
2 l
1.5 l
Q324 Easy

A beam encastered at both the ends is called

Cantilever beam
Simply supported beam
Fixed beam
Continuous beam
Q325 Easy

Dynamic friction as compared to static friction is

Same
More
Less
May be less of more depending on nature of surfaces and velocity
Q326 Easy

What is the bending moment at the free end A of a cantilever beam with no load or moment applied at A?

Zero
8 Tm
12 Tm
20 Tm
Q327 Easy

In a shaft rotated by a couple, the shear force varies

From zero at the centre to a maximum at the circumference
From minimum at the centre of maximum at the circumference
From maximum at the centre to zero at the circumference
Equally throughout the section
Q328 Easy

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is

Pd/2t
Pd/4t
Pd/t
2pd/t
Q329 Easy

A long vertical member, subjected to an axial compressive load, is called

A column
A strut
A tie
A stanchion
Q330 Easy

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is

Zero
Pr/TE
Pr/2TE
None of these
Q331 Easy

What is the highest stress that a material is capable of developing?

Compressive Stress
Yield Stress
Ultimate Stress
Tensile Stress
Q332 Easy

A ____ is an electronic circuit

Voltage limiter
Current limiter
Short circuit
Voltage regulator
Q333 Easy

If a three hinged parabolic arch carries a uniformly distributed load on its entire span, every

Section of the arch resists.
Compressive force
Tensile force
Shear force
Q334 Easy

A measure of the deformation of the material that is what is it?

Elasticity
Inch
Young's modulus
Dimensionless
Q335 Easy

The possible loading in various members of framed structures are

Compression or tension
Buckling or shear
Shear or tension
All of the above
Q336 Easy

While testing a cast iron beam (2.5 cm × 2.5 cm) in section and a metre long simply supported at the ends failed when a 100 kg weight is applied at the centre. The maximum stress induced is:

960 kg/cm2
980 kg/cm2
1000 kg/cm2
1200 kg/cm2
Q337 Easy

Reactions at the supports of a structure can be determined by equating the algebraic sum of

Horizontal forces to zero
Vertical forces to zero
Moment about any point to zero
All the above
Q338 Easy

A reinforced concrete beam is assumed to be made of

Homogeneous material
Heterogeneous material
Isotropic material
None of these
Q339 Easy

Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the unpunched plate in

Tension
Compression
Bearing
Any one of the above
Q340 Easy

The section modulus of a rectangular section is proportional to

Area of the section
Square of the area of the section
Product of the area and depth
Product of the area and width
Q341 Easy

When a rectangular beam is loaded longitudinally, shear develops on

Bottom fibre
Top fibre
Middle fibre
Every-horizontal plane
Q342 Easy

A simply supported beam carries equal and opposite couples of size M at its two ends, so it is in pure bending. What is the shape of its bending moment diagram?

A rectangle
A triangle
A trapezium
A parabola
Q343 Easy

What is the cross-sectional area of an element in tension?

Tension
Pressure
Elongation
Stress
Q344 Easy

The units of moment of inertia of mass are

Kg m²
M4
Kg/m²
Kg/m
Q345 Easy

According to principle of transmissibility of forces, the effect of a force upon a body is

Maximum when it acts at the center of gravity of a body
Different at different points in its line of action
The same at every point in its line of action
Minimum when it acts at the C.G. of the body
Q346 Easy

An arch with three hinges, is a structure

Statically determinate
Statically indeterminate
Geometrically unstable
Structurally sound but indeterminate
Q347 Easy

Which of the following has no unit

Kinematic viscosity
Surface tension
Bulk modulus
Strain
Q348 Easy

What is the result of direct shear stress?

One member is lifted while the other is compressed.
Members rotate relative to each other.
One member slides relative to another member.
Both members slide in the same direction.
Q349 Easy

During a tensile test on a specimen of 1 cm cross-section, maximum load observed was 8 tonnes and area of cross-section at neck was 0.5 cm2. Ultimate tensile strength of specimen is

4 tonnes/cm2
8 tonnes/cm2
16 tonnes/cm2
22 tonnes/cm2
Q350 Easy

For which material the Poisson’s ratio is more than unity

Steel
Copper
Aluminium
None of the above.
Showing 350 of 360 questions

Teachers: using these Strength of Materials questions with a class? Tell us about your class.

Report a mistake

What's wrong?